1 / 9

Chapter 14 Single-Transistors Amplifiers

Chapter 14 Single-Transistors Amplifiers. Microelectronic Circuit Design Richard C. Jaeger Travis N. Blalock. Chap 14 - 1. Noninverting Amplifiers: Common-Base and Common-Gate Circuits. AC equivalent for C-E Amplifier. AC equivalent for C-S Amplifier. Chap 14 - 2.

jkavanaugh
Download Presentation

Chapter 14 Single-Transistors Amplifiers

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Chapter 14Single-Transistors Amplifiers Microelectronic Circuit Design Richard C. Jaeger Travis N. Blalock Microelectronic Circuit Design, 3E McGraw-Hill Chap 14 - 1

  2. Noninverting Amplifiers: Common-Base and Common-Gate Circuits AC equivalent for C-E Amplifier AC equivalent for C-S Amplifier Microelectronic Circuit Design, 3E McGraw-Hill Chap 14 - 2

  3. C-B and C-G Amplifiers: Terminal Voltage Gain and Input Resistance For C-S Amplifier, take limit of voltage gain of C-E amplifier as Polarities of vbe and dependent current source gmvbe are both reversed, signal source is transformed to its Norton equivalent ro is neglected. Microelectronic Circuit Design, 3E McGraw-Hill Chap 14 - 3

  4. C-B and C-G Amplifiers: Overall Voltage Gain Overall voltage gain is For C-S Amplifier, For RI >> R6, For , This is the upper bound on gain. For , ro can be neglected as gain<< mf Microelectronic Circuit Design, 3E McGraw-Hill Chap 14 - 4

  5. C-B and C-G Amplifiers: Input Signal Range For small-signal operation, In case of FET, Relative size of gm and RI determine signal-handling limits. …for RI >> R4. Microelectronic Circuit Design, 3E McGraw-Hill Chap 14 - 5

  6. C-B and C-G Amplifiers: Voltage Gain Calculations (Example) • Problem: Find overall voltage gain. • Given data: Q-point values and values for R1, R2, R3, R7 ,for both BJT and FET, RI =2 kW, R4 =12 kW. • Assumptions: Small-signal operating conditions. • Analysis: For C-E Amplifier, For C-S Amplifier, Microelectronic Circuit Design, 3E McGraw-Hill Chap 14 - 6

  7. C-B and C-G Amplifiers: Output Resistance Desired resistance is that looking into collector with base grounded and resistor Rth in emitter. The redrawn equivalent circuit is same as that for C-E amplifier except resistance in base is zero and resistance in emitter is relabeled as Rth. And for the FET C-G amp Microelectronic Circuit Design, 3E McGraw-Hill Chap 14 - 7

  8. Noninverting Amplifiers: Current Gain • Terminal current gain is the ratio of the current delivered to the load resistor to the current being supplied to the base terminal. Microelectronic Circuit Design, 3E McGraw-Hill Chap 14 - 8

  9. C-B and C-G Amplifiers: Summary • C-B and C-G amplifiers have similar voltage and current gains. Numerical differences occur due to difference in parameter values of BJT and FET at similar operating points. • C-B amplifier can achieve high output resistance due to higher amplification factor of BJT. • C-B amplifier can more easily reach low levels of input resistance due to higher transconductance of BJT for a given operating current. • Input signal range of C-G amplifier is inherently larger than that of C-B amplifier. Microelectronic Circuit Design, 3E McGraw-Hill Chap 14 - 9

More Related