1 / 17

Cause and Effect Analysis

Sigma Quality Management. -6. -4. -2. 0. 2. 4. 6. Cause and Effect Analysis. Cause & Effect in Business Processes. Y = F(X). Input (X). Process (X). Output (Y). Methods Materials Machines Personnel Environment. Roadmap for Analyzing Causes. From Measure Step.

Download Presentation

Cause and Effect Analysis

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Sigma Quality Management -6 -4 -2 0 2 4 6 Cause and Effect Analysis

  2. Cause & Effect in Business Processes Y = F(X) Input (X) Process (X) Output (Y) • Methods • Materials • Machines • Personnel • Environment

  3. Roadmap for Analyzing Causes From Measure Step Examine the Process, Address Assignable/ Special Causes of Variation Check Process and Make Quick and Easy Improvements Stratify Data to Identify Specific Problems Develop Cause and Effect Diagrams for the Specific Problems Verify Root Causes To Improve & Execute Steps

  4. Simple Cause & Effect • Examining the Process • Common Sense • Process Documentation • Actual vs. Documented Process • Training • Data Analysis • Quick and Easy Improvements • Eliminate redundancies • Clarify unclear steps • Re-order steps • Eliminate unnecessary steps • Decrease the amount of transportation or delays

  5. Simple Cause & Effect • Stratifying the Data – Pareto • Involving the Right People

  6. Cause & Effect (Ishikawa) Diagram Kaoru Ishikawa – Our Hero!

  7. Steps 1. State the problem as the Effect. A good "Effect" statement: • states what is wrong, not why it is wrong, • focuses on the gap between what is and what should be, and • is measurable and specific. 2. Identify possible causes of the Effect. Brainstorm a list of causes based on knowledge of the production process. • "Ask Why Five Times" • Avoid: • Solutions • "Lack of" Statements • "Fuzzy" causes

  8. Steps (continued) 3. Define the major categories to be used on the Cause and Effect diagram. “Default" categories - Person, Machine, Material, Method, Information, and Environment. 4. Draw the diagram. Refine the causes where necessary and continue asking: • What causes this? • Why does this condition exist? 5. Walk through the logic in both directions: • proceed from the effect to the causes, and • proceed from the causes to the effect.

  9. Variation/Problem Analysis Type

  10. Production Process - Focused

  11. Others • Comparative Cause & Effect • Planning Cause & Effect

  12. Cause & Effect Verification CAUSE AND EFFECT DIAGRAM Environment Person Machine Root Effect Cause G Root Cause A Material Method G Spec E D A B C

  13. Verification Methods - Absence/Presence

  14. Verification Methods - Absence/Presence Causes of Defects 127 125 100 75 50 25 0 100 75 50 25 0 Frequency % of defects A B

  15. Verification Methods - Absence/Presence Performance With Factor Absent Frequency Value Performance With Factor Present Frequency Value

  16. Automobile Gas Mileage 26 Gas Mileage (MPG) 20 Driving Speed (MPH) 35 75 Verification Methods – Variable Level

  17. Verification Matrix Tests/Verifications Problem Potential Causes Mat'l Test Oil Sample Weibull An'l. Fracture An'l. Dimensioning Mat'ls Tested Batch of Sleeves with poor OK material properties Mixing of Lubricating Oils Not a Problem for Journal Box Lubr. Case Hardened vs. Through Other Roads Hardened steel use Case, ours Inner Sleeve uses Through Cracking Replacement interval too long B - 10 Life is 38 Mo., we repl. on 60 Mo. Contamination in Lube Oil High Sand levels found in J.B. Oil Excessive Stress on Sleeves Fracture Rpt. indicates High Stress on Axle Inadequate Interference Fit - 1% Chance of Combination Sleeve too Large too small inter. and Axle too Small (specs) fit (30 data) Axle Upset due to Wheel Pulling Axles meas'd. no taper or out Stresses of round

More Related