1 / 12

Silicon microchannels studies for the ITS upgrade

Silicon microchannels studies for the ITS upgrade. Francescon ITS-MFT mini-week 12.03.14. Silicon micro-channels for electronics cooling. CMOSAIC collaboration 3D Stacked Architectures with Interlayer Cooling (CMOSAIC). Agostini et al. (2008) High heat flux flow boiling

bin
Download Presentation

Silicon microchannels studies for the ITS upgrade

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Silicon microchannels studies for the ITS upgrade Francescon ITS-MFT mini-week 12.03.14

  2. Silicon micro-channels for electronics cooling CMOSAIC collaboration 3D Stacked Architectures with Interlayer Cooling (CMOSAIC) Agostini et al. (2008) High heat flux flow boiling in silicon microchannels • High heat transfer rate • Uniform temperature (if flow boiling) • Low mass flow rate operation • Reduced dimensions

  3. Silicon microchannels for tracking detectors • When addressing the thermal management of the on-detector electronics fro HEP tracking detectors, the design is complicated by different constraints: • Minimization of the material budget • Cooling of large active areas • Strict geometrical and integration constraints

  4. Silicon microchannels for tracking detectors • When designing cooling system for the tracking detectors, the design is complicated by different constraints: • Minimization of the material budget • Cooling of large active areas • Strict geometrical and integration constraints Special frame design

  5. First prototype of silicon frame with embedded microchannels 60x15 mm2 Silicon dummy chip 100 μm thick

  6. Results at qchip=0.3 W/cm2 The test was performed at the nominal power dissipation expected for the pixel chip. G=300 [kg·m-2·s-1] Tin=21°C Tsat=22.5°C G=750 [kg·m-2·s-1] Tin=19.5°C Tsat=21°C Dummy chip top surface with two electrodes and seven thermocouples At the nominal power dissipation expected for the pixel chip the system is able to maintain the detector surface within the thermal constraints.

  7. Silicon microchannels for tracking detectors • When designing cooling system for the tracking detectors, the design is complicated by different constraints: • Minimization of the material budget • Cooling of large active areas • Strict geometrical and integration constraints The ˝micro-bridge˝

  8. Interconnected silicon microchannel devices Silicon microchannel devices are limited in dimensions by the diameter of the silicon wafer used as substrate for the microfabrication. At this stage of the development, 4” wafers are used but tests on 6” wafers are on-going. However, even using 8” wafers still it would not be possible to reach the length of the ITS inner layers stave. Using larger wafers would lead to a device very hard to handle during the following integration steps. For this reason, the interconnection of several silicon microchannel devices is mandatory. In order to guarantee the interconnection of silicon microchannel devices, we developed the concept of the ˝micro-bridge˝.

  9. Silicon microchannels for tracking detectors • When designing cooling system for the tracking detectors, the design is complicated by different constraints: • Minimization of the material budget • Cooling of large active areas • Strict geometrical and integration constraints Special fluidic design The requirement of having all the services on one side for the extraction of the ITS barrel for maintenance, forced us to develop a special fluidic path for the prototype. Inlet distribution line Micro-bridge Return line

  10. Fabrication of the prototype The devices are fabricated in the EPFL Center of MicroNanotechology (CMi) class 100 clean room using standard microfabrication techniques.

  11. Preliminary thermal tests: single-phase flow Test at 0.1 W/cm2 uniform power dissipation ṁ=0.4 g/s Tin=16 ᵒC

  12. Future plans In collaboration with the Thai MicroEectronic Center (TMEC) in Bangkok, we are developing ultra-thin full silicon frames with embedded microchannels on 6˝ wafers. This will require only 2 frames for the cooling of a full IB stave. 160 μm! Before bonding 410 μm

More Related