1 / 18

VLSI Testing Lecture 2: Yield & Quality

VLSI Testing Lecture 2: Yield & Quality. Yield and manufacturing cost Clustered defect yield formula Defect level Test data analysis Example: SEMATECH chip Summary Problems to solve. VLSI Chip Yield.

fayre
Download Presentation

VLSI Testing Lecture 2: Yield & Quality

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. VLSI Testing Lecture 2: Yield & Quality • Yield and manufacturing cost • Clustered defect yield formula • Defect level • Test data analysis • Example: SEMATECH chip • Summary • Problems to solve Lecture 2 Yield & Quality

  2. VLSI Chip Yield • A manufacturing defect is a finite chip area with electrically malfunctioning circuitry caused by errors in the fabrication process. • A chip with no manufacturing defect is called a good chip. • Fraction (or percentage) of good chips produced in a manufacturing process is called the yield. Yield is denoted by symbol Y. • Cost of a chip: Cost of fabricating and testing a wafer ———————————————————————Yield x Number of chip sites on the wafer Lecture 2 Yield & Quality

  3. Clustered VLSI Defects Good chips Faulty chips Defects Wafer Clustered defects (VLSI) Wafer yield = 17/22 = 0.77 Unclustered defects Wafer yield = 12/22 = 0.55 Lecture 2 Yield & Quality

  4. Yield Parameters • Defect density (d) = Average number of defects per unit of chip area • Chip area (A) • Clustering parameter (α) • Negative binomial distribution of defects,p(x ) = Prob (number of defects on a chip = x ) G(a+x ) (Ad /a) x = ─────── . ────────── x ! G (a) (1+Ad /a) a+x where Γ is the gamma function a = 0, p (x ) is a delta function (maximum clustering) a =∞ , p (x ) is Poisson distribution (no clustering) Lecture 2 Yield & Quality

  5. Yield Equation Y = Prob ( zero defect on a chip ) = p (0) Y = ( 1 + Ad / a ) - a Example: Ad = 1.0, α = 0.5, Y = 0.58 Y = e - Ad Unclustered defects: α = ∞, Example: Ad = 1.0, α = ∞,Y = 0.37 too pessimistic ! Lecture 2 Yield & Quality

  6. Defect Level or Reject Ratio • Defect level (DL) is the ratio of faulty chips among the chips that pass tests. • DL is measured as parts per million (ppm). • DL is a measure of the effectiveness of tests. • DL is a quantitative measure of the manufactured product quality. For commercial VLSI chips a DL greater than 500 ppm is considered unacceptable. Lecture 2 Yield & Quality

  7. Determination of DL • From field return data: Chips failing in the field are returned to the manufacturer. The number of returned chips normalized to one million chips shipped is the DL. • From test data: Fault coverage of tests and chip fallout rate are analyzed. A modified yield model is fitted to the fallout data to estimate the DL. Lecture 2 Yield & Quality

  8. Modified Yield Equation • Three parameters: • Fault density, f = average number of stuck-at faults per unit chip area • Fault clustering parameter, β • Stuck-at fault coverage, T • The modified yield equation: Y (T ) = (1 + TAf / b) - b Assuming that tests with 100% fault coverage (T =1.0) remove all faulty chips, Y = Y (1) = (1 + Af / b) - b Lecture 2 Yield & Quality

  9. Defect Level Y (T ) - Y (1) DL (T ) = ——————— Y (T ) ( b + TAf ) b = 1 – —————— ( b + Af ) b Where T is the fault coverage of tests, Af is the average number of faults on the chip of area A, β is the fault clustering parameter. Afand β are determined by test data analysis. Lecture 2 Yield & Quality

  10. Example: SEMATECH Chip • Bus interface controller ASIC fabricated and tested at IBM, Burlington, Vermont • 116,000 equivalent (2-input NAND) gates • 304-pin package, 249 I/O • Clock: 40MHz, some parts 50MHz • 0.8m CMOS, 3.3V, 9.4mm x 8.8mm area • Full scan, 99.79% fault coverage • Advantest 3381 ATE, 18,466 chips tested at 2.5MHz test clock • Data obtained courtesy of Phil Nigh (IBM) Lecture 2 Yield & Quality

  11. Test Coverage from Fault Simulator Stuck-at fault coverage Vector number Lecture 2 Yield & Quality

  12. Measured Chip Fallout Measured chip fallout Vector number Lecture 2 Yield & Quality

  13. Model Fitting Chip fallout vs. fault coverage Y (1) = 0.7623 Chip fallout and computed 1 -Y (T ) Measured chip fallout Y (T ) for Af = 2.1 and b = 0.083 Stuck-at fault coverage, T Lecture 2 Yield & Quality

  14. Computed DL 237,700 ppm (Y = 76.23%) Defect level in ppm Stuck-at fault coverage (%) Lecture 2 Yield & Quality

  15. Summary • VLSI yield depends on two process parameters, defect density (d ) and clustering parameter (α). • Yield drops as chip area increases; low yield means high cost. • Fault coverage measures the test quality. • Defect level (DL) or reject ratio is a measure of chip quality. • DL can be determined by an analysis of test data. • For high quality: DL < 500 ppm, fault coverage ~ 99% Lecture 2 Yield & Quality

  16. Problems to Solve • Using the expression for defect level on Slide 9, derive test coverage (T) as a function of fault clustering parameter (β), defect level (DL), and average number of faults (Af) on a chip. • Find the defect level for: • Fault density, f = 1.45 faults/sq. cm • Fault clustering parameter, β = 0.11 • Chip area = 1 cm2 • Fault Coverage, T = 95% Lecture 2 Yield & Quality

  17. Solution of Problem 1 Defect level, DL, is given on Slide 9, as follows: DL = 1 – [(β + Taf)/(β + Af)]β where T is the fault coverage, Af is the average number of faults on a chip of area A, and β is a fault clustering parameter. Further manipulation of this equation leads to the following result: (1 – DL)1/β = (β + Taf)/(β + Af) or T = [{(β + Af)(1 – DL)1/β– β}/(Af)] × 100 percent Lecture 2 Yield & Quality

  18. Solution of Problem 2 Defect level, DL, as given on Slide 9, is: DL(T) = 1 – [(β + Taf)/(β + Af)]β Substituting, • Fault density, f = 1.45 faults/sq. cm • Fault clustering parameter, β = 0.11 • Chip area = 1 cm2 • Fault Coverage, T = 95% • We get, • DL(T) = 0.00522 or 5,220 parts per million Lecture 2 Yield & Quality

More Related