1 / 40

SIPROTEC 4 Distance Protection 7SA522 and 7SA6

SIPROTEC 4 Distance Protection 7SA522 and 7SA6. Productmanager Distance Protection Michael Claus EV S V 13 Nürnberg H Phone: +49 911 433 8261 Fax: +49 911 433 8301 Email: Michael.Claus@ev.siemens.de. SIPROTEC 4 is a family of numerical Protection, Control and Automation Devices

fallon
Download Presentation

SIPROTEC 4 Distance Protection 7SA522 and 7SA6

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. SIPROTEC 4Distance Protection 7SA522 and 7SA6 Productmanager Distance Protection Michael Claus EV S V 13 Nürnberg H Phone: +49 911 433 8261 Fax: +49 911 433 8301 Email: Michael.Claus@ev.siemens.de

  2. SIPROTEC 4 is a family of numerical Protection, Control and Automation Devices from SIPROTEC 4 -What it means

  3. 7SA510 SIPROTEC 4 Software System 7SA511 7SA513 System Experience Requirements 7SA522 7SA6 Variability SIPROTEC 4Hardware Platform Distance protection: Past and Present

  4. 7SA522 + 7SA6 One family of distance protection for all voltage applications SIPROTEC 4Distance Protection 7SA522 and 7SA6

  5. 7SA610 7SA612 + 7SA522 7SA611 + 7SA522 7SA631 7SA632 7SA641 7SA642 All core functions are available in all the housing versions SIPROTEC 4 Distance protection 7SA61 +7SA522 Protection 4-line display MV, HV and EHV 7SA63 Protection + local control integrated graphic display mainly MV 7SA64 Protection + local control detached control panel mainly MV

  6. ANSI-No. • 21, 21N • 68 • FL SIPROTEC 4 Distance Protection, Scope of functions (1) • Distance Protection • full scheme measurement with sophisticated loop selection • fast three phase and single phase tripping • with/without parallel line compensation • special filtering for CVT transients • special algorithm for detection and compensation of CT saturation  Low demand on CT specification • Power swing blocking/out-of-step tripping • Fault Locator with/without parallel line compensation 17.10.97 en513all7

  7. ANSI-No. • 85-21 • 50N, 51N, 67N • 85-67N • WI • 50, 5150N-2, 51N-2 SIPROTEC 4 Distance Protection, Scope of functions (2) • Universal teleprotection interface (PUTT, POTT, Blocking, Unblocking, DTT...) • High resistance earth fault protection for earthed systems • Teleprotection interface for earth fault protection (Directional comparison, Blocking, Unblocking) • Weak infeed protection(Echo and Trip) • Overcurrent protection DMTL/IDMTL as parallel or emergency function 17.10.97 en513all8

  8. ANSI-No. • 59, 27 1) • 50HS • 50-STUB • 79 • 25 • 50BF • 49 2) SIPROTEC 4 Distance Protection, Scope of functions (3) • Voltage protection 1) • Fast tripping with switch-onto-fault condition (12 ms) • STUB Bus Overcurrent protection • Single and three pole multishot automatic reclosure • Synchro-check • Circuit-breaker failure protection • Thermal overload protection 2) • Earth fault detection in compensated/isolated systems 2) 1) 7SA522: Overvoltage, 7SA6: Over- and Undervoltage 2) available only in 7SA6

  9. SIPROTEC 4 Distance Protection, Scope of functions (4) ANSI-No. 74TC 86 FR 47 • Trip Circuit Supervision • Lock Out • Oscillographic Fault Recording (total length 15 s) • Voltage Phase Sequence • Interfaces • Time synchronization (IRIG-B, DCF77) • User interface#1 (on the front for DIGSI 4) • User-(Service-)interface #2 (on the rear, DIGSI 4/Modem) • System interface (IEC60870-5-103/Profibus FMS/others) • Remote relay interfaces #1 (planned for teleprotection*) • 1) Remote relay interfaces #2 (planned for teleprotection*) * available approx. 1st Q/01 1) available only in 7SA522

  10. Operating system monitoring Auxiliary voltage failure Measured value detection Buffer battery Hardware–Watchdog Software–Watchdog Working memory Program memory Parameter memory Sampling frequency 1/5 A–setting Calibration data Earth current transformer sensitive/normal Modules (I/O Boards) ! SIPROTEC 4 Distance Protection, Monitoring Plausibility monitoring • Current sum • Current symmetry • Open conductor • Fuse Failure • 1- / 2-pole failures • 3-pole failures • Voltage sum • Voltage symmetry • Voltage phase rotation new

  11. SIPROTEC 4 Distance Protection Quadrilateral Characteristic 5 Zones (time delayed) optionally: - Forward- Reverse- Non-directional Dependant Zone Z1b for Teleprotection andAuto-recloser Prevention of load encroachment

  12. SIPROTEC 4Distance Protection: Overall Trip Time Curves at SIR = 30

  13. SIPROTEC 4 Distance Protection, Data window position, Adaptive Measuring Algorithm

  14. SIPROTEC 4 Distance Protection Function: Difference 7SA522 - 7SA6 • 7SA522 • for solid earthed systems • quadrilateral and/or MHO characteristic(MHO circle for specific markets, quadrilateral is preferred) • full market introduction: 1999 • primary market outside continental Europe • 7SA6 • for systems with solid grounding or reactance (compensated) / isolated treatment of system starpoint • fault detection selectable as either I>, Z<, U/I and U/I/ • Market introduction: Summer 2000 • Primary market continental Europe

  15. SIPROTEC 4 Distance Protection 7SA522 Mho Characteristic 5 Zones optionally: - Forward- Reverse Dependant Zone Z1b for Teleprotection andAuto-recloser Prevention of load encroachment

  16. SIPROTEC 4, Distance ProtectionParallel-line compensation: connection and setting

  17. Patented power swing detection provides secure operation with swing frequencies of up to 6 Hz Example: 400 kV 400 km fPS 2 Hz 3-pole fault

  18. SIPROTEC 4 Distance Protection:Fault locator

  19. SIPROTEC 4 Distance Protection: Phase segregated Teleprotection 2 2 L2-E Z1 Z1B L1-E 1 1 B A Z1B Z1 • A1 trips single-phase in L1 with a phase-segregated L1-receive-signal • Maximum of Selectivity Note: 3 binary channels for both directions are requested or (in preparation) one serial link

  20. SIPROTEC 4 Distance Protection: Teleprotection with three-terminal lines Software provides teleprotection of three-terminal lines without additional logic

  21. SIPROTEC 4 Distance Protection: High Resistance Earth Fault Protection • Earth (zero sequence) current protection, 4 stages • 3 definite-time stages • 1 inverse-time stage: IEC, logarithmic inverse or ANSI characteristicthis stage can also be used as a 4th definite-time stage • Directional determination with 3V0 and/or Ipol of an earthed power transformer • Directional determination with V2 and I2 (negative sequence) • Sensitive 3I0-measurement with a dynamic from 0.003 A to 100 x In • Elimination of higher harmonics with special digital filters • Inrush-stabilisation with I0/100Hz • Teleprotection: Directional comparison, Blocking or Unblocking • Operation with weak infeed trip and echo • Instantaneous trip after switch-onto-fault

  22. SIPROTEC 4 Distance Protection: High Resistance Earth Fault Protection Definite-time characteristic

  23. SIPROTEC 4 Distance Protection: High Resistance Earth Fault Protection Tripping characteristic Logarithmic Inverse t T3I0pmax (P3145) T3I0p (P3144) 3I0p(P3140) Example: t = 5.8 - 1.35 ln(3I0 / 3I0p) T3I0min (P3141) 3I0 / 3I0p 3I0p Startpoint(P3154)

  24. SIPROTEC 4 Distance Protection: High Resistance Earth Fault Protection

  25. SIPROTEC 4 Distance Protection: High Resistance Earth Fault Protection Inverse-time characteristic: IEC

  26. SIPROTEC 4 Distance Protection: High Resistance Earth Fault Protection Filter characteristic for stages 3I0>>> and 3I0>>

  27. SIPROTEC 4 Distance Protection: High Resistance Earth Fault Protection Filter characteristic for stages 3I0> and Inverse time stage

  28. SIPROTEC 4 Distance Protection: High Resistance Earth Fault Protection

  29. SIPROTEC 4 Distance Protection: Permissive overreach transfer trip (POTT) TS

  30. SIPROTEC 4 Distance ProtectionSTUB protection for 11/2-circuit breaker arrangement Release of STUB-stage with open line isolator:

  31. TRIP 1-pole 3-pole RE- CLOSE * TRIP RE- CLOSE final TRIP ON 2nd dead time OFF 1st dead time tzone-delay T1-act T2-act SIPROTEC 4Distance Protection: Auto-reclosure Auto-reclosure (AR) * ADT = Reclosure, when AR at the remote end was successful DLC = Reclosure only on dead line RDT = Reduced dead time, if trip had occurred with zone extension

  32. Synchronism-check application examplesfunctions (separately settable for AR and - combination with internal or manual closing) external AR - program selection via parameters: - activation also for manual closing synchro-check / U1 > U2 < / (settable) U1 < U2 > / U1 < U2 < / overrule - asynchronous switching (settable) - all programs separately settable via binary inputs - synchronous monitoring time, after which the closing will be blocked (settable) parametersmeasurement - voltages U<, U>, U - evaluation of the fundamental wave - f synchronous switching (0.01 ... 0.03 Hz) - insensitive against harmonics - f asynchronous switching (0.03 ... 1 Hz) - for dead line check all three phases are controlled -  (1° ... 60°) 16.10.97 engersyn1

  33. SIPROTEC 4 Distance Protection: Breaker failure protection • 2 stages • Internal initiation and via binary inputs • Extremely short reset time: approx. 10ms • End-fault protection • Pole discrepancy supervision

  34. SIPROTEC 4Distance Protection 7SA522 with light or electrical • exchangeable • upgradeable

  35. User friendly Operation SIPROTEC 4 -Distance Protection Safe operation, reduced training requirements Fits all applications • Flexible Functionality and • Open Communication System concept SIPROTEC and SICAM One Family

  36. Full Logic Functionality F1 Log. IN 1 Log.OUT1 >1 F2 Log. IN 2 CFC Log.IN3 Logic outputs to the configuration matrix Logic inputs from the matrix to CFC Distance Protection 7SA522What makes these devices so attractive ? Additional logic Interlocking Measured values processing

  37. Comprehensive measured value processing L1 402.1A Max450.1A L2 401.2A Max421.2A L3 401.0A Max431.4A E 00.0A % IL UL-E UL-L L1 100.0 100.4 100.1 L2 100.4 100.3 100.0 L3 100.1 100.1 100.4 Distance Protection 7SA522What makes these devices so attractive ? I1 :400.9A f:50.0Hz U1:12.22kV P :+8.03MW cos Q :+2.64MVar

  38. The easy handling with DIGSI 4 Distance Protection 7SA522What makes these devices so attractive ?

More Related