Download
slide1 n.
Skip this Video
Loading SlideShow in 5 Seconds..
PRESENT PowerPoint Presentation

PRESENT

122 Views Download Presentation
Download Presentation

PRESENT

- - - - - - - - - - - - - - - - - - - - - - - - - - - E N D - - - - - - - - - - - - - - - - - - - - - - - - - - -
Presentation Transcript

  1. PRESENT

  2. DECORATIVE SINGLE COAT PLASTER FOR MARBLE CHIPS CLADDING SYSTEM ( PEBBLEDASH )

  3. WATER PROOF COLORED CEMENT BASED MORTAR WITH GOOD ADHESION, FOR THE PROTECTION AND DECORATION OF FAÇADES

  4. WATER REPELLENT WHILE AT THE SAME TIME ALLOWING THE STRUCTURE TO BREATHE

  5. EXCELLENT DIRT PICK-UP RESISTANCE AND IS EXTREMELY STABLE AGAINST ULTRA VIOLET LIGHT EVEN IN SEVERE CLIMATIC CONDITIONS

  6. APPLIED MANUALLY AND AVAILABLE IN A RANGE OF 12 COLORS

  7. PROPERTIES

  8. FORMULATED USING A MIXTURE OF PRECISELY GRADED FILLERS, CEMENT, PRELATE, SILICA SAND, PIGMENTS AND ADDITIVES

  9. FINISHED BY SPRAYING A LAYER OF MARBLE CHIPS OVER THE SURFACE AND WORKING THEM INTO THE SURFACE WITH A STEEL TROWEL.

  10. ADVANTAGES

  11. LONG LIFE

  12. 2. DIRT PICK-UP RESISTANCE

  13. 3. EXCELLENT UV STABILITY

  14. 4. WATER REPELLENT

  15. 5. PLASTERING / FINISHING IN ONE OPERATION

  16. 6. GOOD MECHANICAL STRENGTH

  17. AREA OF USE

  18. EXTERIOR WALL FOR DIRECT APPLICATION ON CLAY BRICK, CONCRETE BLOCK, AAC BLOCK, PRECAST/IN-SITU CONCRETE AND STONE.

  19. PREPARATION OF SURFACE

  20. 1. ENSURE ALL DUST, DIRT AND FOREIGN MATTER ARE BRUSHED AND SCRAPED AWAY.

  21. 2. ENSURE SURFACE IS SOLID, FREE FROM SALTS, OIL, GREASE AND RIDGES.

  22. 3. PROTECT ALL ADJACENT SURFACES NOT TO BE COATED.

  23. 4. APPLY A COAT OF PENETRATING PRIMER TO ABSORBENT SURFACES SUCH AS AAC BLOCKS.

  24. 5. A KEY COAT IS REQUIRED ON VERY SMOOTH SURFACES SUCH AS PRECAST OR IN-SITU CONCRETE (1PT MAR-FIX, 0.4 PTS. WATER, 0.08 PTS. BOND)

  25. MIXING

  26. 1. MIX 20 KG OF MAR-FIX WITH 5–6 LITERS OF CLEAN WATER FOR 3 MINUTES.

  27. 2. Ensure that mixing time and ratio of powder/ water are constant to ensure color consistency.

  28. 3. ALLOW THE MORTAR TO STAND FOR 5 MINUTES, REMIX AND USE. PREPARED MATERIAL SHOULD BE USED WITHIN ONE HOURS.

  29. 3. ALLOW THE MORTAR TO STAND FOR 5 MINUTES, REMIX AND USE. PREPARED MATERIAL SHOULD BE USED WITHIN ONE HOURS.

  30. APPLICATION AND CLEANING OF TOOLS

  31. 1. SATURATE THE SUBSTRATE WITH WATER TO REDUCE SUCTION OF WATER FROM THE PRODUCT THE DAY BEFORE APPLICATION AND AGAIN ONE HOUR BEFORE APPLICATION.

  32. 2. SPREAD THE MORTAR OVER THE SUBSTRATE IN A 4-6 MM LAYER.

  33. 3. TROWEL TO A SMOOTH LEVEL SURFACE.

  34. 4. AFTER A PERIOD OF APPROX. 10 MINUTES SPRAY THE MARBLE CHIPS OVER THE MORTAR.

  35. 5. TAMP THE SURFACE WITH A TROWEL TO EMBED THE CHIPS INTO THE MORTAR.

  36. 6. CLEAN EQUIPMENT WITH CLEAN WATER IMMEDIATELY AFTER USE.

  37. PRECAUTIONS

  38. 1. DO NOT APPLY BELOW 8 DEGREE CELSIUS AS THERE IS RISK OF EFFLORESCENCE.

  39. 2. DO NOT APPLY ON HORIZONTAL OR SLOPING SURFACES.

  40. 3. DO NOT APPLY ON GYPSUM-BASED SUBSTRATES.

  41. 4. DO NOT USE AT GROUND LEVEL TO AVOID STAINING.

  42. 5. WHEN APPLYING AT HIGH TEMPERATURES, ENSURE THAT SURFACE IS CURED FOR AT LEAST 72 HOURS AFTER APPLICATION.

  43. HEALTH & SAFETY

  44. 1. AVOID PROLONGED CONTACT WITH EYES AND SKIN.

  45. 2. AVOID BREATHING DUST. FOR DETAILED INFORMATION REFER TO THE RELEVANT MATERIAL SAFETY DATA SHEET.

  46. PACKAGING & STORAGE

  47. 1. PACKED IN A POLYPROPYLENE SACKS OF 20 KG NET WEIGHT ON WOODEN PALLETS.

  48. 2. SHOULD BE STORED IN A CLEAN, SHADED, AND DRY AREA AS SUPPLIED.

  49. 3. UNOPENED BAGS CAN BE STORED FOR 6 MONTHS.