1 / 20

Ground Control

Ground Control. Jordan Hodge Jordan Lyford Wilson Schreiber. Contents. Background Problem Statement Solution Mechanical Azimuth Elevation Static and Dynamics of System Software SatPC32 Interpolation Programming Electrical/Controls RS232 Controller Timeline Responsibilities.

rhona
Download Presentation

Ground Control

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Ground Control Jordan Hodge Jordan Lyford Wilson Schreiber

  2. Contents • Background • Problem Statement • Solution • Mechanical • Azimuth • Elevation • Static and Dynamics of System • Software • SatPC32 • Interpolation • Programming • Electrical/Controls • RS232 • Controller • Timeline • Responsibilities

  3. Background • VTC developing CubeSat, transmits data • Continuing where previous groups have left off • Have to follow CubeSat to receive data • Existing 3-meter parabolic dish antenna • Low orbit satellite revolves around earth in minutes, seen for short time per orbit • Existing solutions • EGIS Bi-axial antenna positioning system

  4. Problem • Track a low orbit satellite such as a CubeSat from horizon to horizon in as little as 30 seconds 180°/30 seconds=6°/sec • Move a 3 meter satellite dish • 360° Azimuth (left/right) • 180° Elevation (up/down) • Interface to PC running SatPC32

  5. Solution • Gears and motors, motor controllers • FreescaleColdfire 32-bit Microcontroller • Serial interface with SatPC32 simulating the functions of EGIS controls • Magnetic Encoders sense rotor/dish position • Use/Modify existing designs for elevation and azimuth control

  6. Available Solution • EGIS- Current market solution • Cost: • Software $400 • Data Interface $1,100 • Hardware $2,700 (EL-40°, AZ-180°) • Extension $2,200 (EL-90°, AZ-360°) • Rotor Hardware Mount $400 • Satellite Dish Mount $400 • Total $7,200

  7. Mechanical Design • Probable Azimuth/ Elevation Configurations: • Fork Mount • Same simple left-right/up/down characteristics • Allows the dish to go over backwards if it needs to.

  8. Mechanical Design • Equatorial Mount: • The movement of the Azimuth (here the Declination Axis) makes an arc in the sky. • The Elevation (a) is set parallel to the earths axis of rotation. This system is much more accurate than the Fork and needs a much less complicated control system.

  9. Mechanical Concepts • Azimuth • A left to right angle measurement from a fixed point (north in navigation) • Worm Gears • Speed (Gear Ratio) • Torque • Modify existing designs

  10. Mechanical Design Choosing a Solution: • Knowing the Satellite path ultimately determines what setup is best. • If the Satellite orbit is not a polar orbit, then the Equatorial Mount might be the best choice.

  11. Mechanical Design Choosing a Solution: • If there is a polar orbit, or strange orbit all together: • The Dish with the Fork configuration may be the best choice.

  12. Mechanical Design Statics and Dynamics: Key Points of Interest: • Dynamic Torque- The torque encountered by a system that is not only in motion, but accelerating. • Static Torque- The torque produced at constant velocity (rest or running). • Center of Mass- The mean location of all system masses. • Moment of Inertia- A measure of an object's resistance to changes to its rotation. It is the inertia of a rotating body with respect to its rotation.

  13. Mechanical Design PhysicalDimensions:

  14. Mechanical Design Torque Calculations: • TStarting=KrunningTrunningKrunning= Running Torque Multiplier • To= [ 5250 x HP ] / N To= Operating or running Torque ( ft-lbs ) | • HP = Horsepower delivered by electric motor **Note: Values switch from N = Rotational velocity ( rpm)| metric to English Units 5250 = Constant converting horsepower to ft-lbs/minute and work/revolution to torque • T = [ N x WR2 ] / [ Ta x 308 ] T  = Time ( seconds )|N = Velocity at load (rpm ) Ta = Average Torque During start ( ft-lbs) WR2 =  Rotating Inertia (lbs-ft3)|W =Weight (lbs) R = Radius of Gyration (ft2)| 308 = Constant derived converting minutes to seconds, mass from weight, and radius to circumference

  15. Mechanical Design Alternatives to Predict Key Points of Interest: • SolidWorks- Flow Works • Scaling system down and measure accordingly

  16. SatPC32 • A free software available online for tracking satellites. Updates on screen and controls rotor to point to position satellite • Uses orbit of satellite and observer position • Many types of rotors to select for output • Uses Serial port or Parallel port on PC

  17. Software- SatPC32 WinListen predicts path Screen Shot of SatPC32 in use

  18. System Diagram SatPC32 EL - Motor Controller RS232 AZ - Motor Controller Micro- controller Position Encoders Limit Switches

  19. Programming • Read new position from serial port • Stores values when they come in • Read actual position from encoders • Measure periodically • Decide where to turn, how fast • Always checking limit switches • If ever activated, stop motors New Serial? Read Serial Check Encoders? Read Encoders Controller (Set Outputs)

  20. Questions?

More Related