1 / 35

ECGD 4121 – Transportation Engineering I Lecture 8

Faculty of Applied Engineering and Urban Planning. Civil Engineering Department. 2 nd Semester 2008/2009. ECGD 4121 – Transportation Engineering I Lecture 8. Intersections Design & Control. Content. Intersections Interchanges Grade-separated intersections At-grade intersections

hayes-bauer
Download Presentation

ECGD 4121 – Transportation Engineering I Lecture 8

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Faculty of Applied Engineering and Urban Planning Civil Engineering Department 2nd Semester 2008/2009 ECGD 4121 – Transportation Engineering I Lecture 8

  2. Intersections Design & Control

  3. Content • Intersections • Interchanges • Grade-separated intersections • At-grade intersections • Channelization • Clearly defined travel paths for vehicles

  4. Interchanges • Ramps at different levels connecting two or more freeways

  5. Grade-separated Intersections • Two intersecting highways connected at different elevations

  6. At-grade Intersections • Two intersecting roads connected at the same elevation

  7. At-grade Intersections • Two intersecting roads connected at the same elevation

  8. Objectives of Traffic Channelization • To establish clear definition of vehicle paths • To control movement of traffic • To provide safe refuge for pedestrians • To separate traffic conflicts • To provide safe merging/diverging of traffic

  9. Channelized Intersections

  10. Intersections Control • Objective: to reduce the conflict points at an intersection • Method of control depends on: • Type of intersection (4-way, T-Intersection, etc.) • Traffic volume in each conflicting stream • Guidelines provided in Manual on Uniform Traffic Control Devices (MUTCD) • Guidelines presented in the form of warrants (i.e. conditions that call for intersection control)

  11. Intersection Control Using Yield Signs • Eliminates crossing conflicts • Used at major road-minor road intersections • Warrants: • Approach speed on minor road > 10 mph • When there is a separate channelized lane without adequate acceleration lane

  12. Intersection Control Using Stop Signs • Eliminates crossing & merging conflicts • Inconvenient to motorists • Used where approaching vehicle has to stop before the intersection • Warrants: • Minor road intersects with major road • Presence of hazardous conditions such as high approach speed, restricted view, and history of accidents

  13. Intersection Control Using Multi-Way Stop Signs • Used when traffic volumes on all approaches are approximately equal • For too high traffic volumes, use signals • Warrants: (satisfy all) • Total int. approach volume > 500 vph for any 8 hours of average day • Combined vehicle + pedestrian volume for minor approach > 200 units per hour for same 8-hr. period • Avg. vehicle delay on minor street > 30 sec/veh for max. hr • If 85th percentile approach speed on major approach is > 40 mph

  14. Intersection Control Using Traffic Signals • When minor road traffic suffers excessive delays • Minimum pedestrian volume: • Ped. Volume crossing major street > 100 for any 4 hrs • Ped. Volume crossing major street > 190 for any 1 hr • Traffic leaves less than 60 gaps accepted by pedestrians per hour • Nearest traffic signal > 300 ft. away • Use traffic actuated signal, push button operation for pedestrians

  15. Intersection Control Using Traffic Signals • School crossings • Used when traffic gaps are inadequate for safe crossing • When no. of accepted gaps < minutes in period • No parking within 100 ft. before and 20 ft. after crossing • Progressive movement • Exception to other warrants when it helps to maintain grouping of vehicles to regulate the group speed • Accident experience (when signal is suitable) • 5 or more injury in 12 months

  16. Intersection Control Using Traffic Signals • Peak hour delay: delay and volume in any 4 consec. 15-min periods when controlled by stop sign is: • > 4 veh-hrs & 100 vph for 2-lane minor street approach • > 5 veh-hrs & 150 vph for 2-lane minor street approach

  17. Signal Timing - Terminology • Controller - fixed or variable timing • Cycle (one complete color sequence) • Phase-part of cycle allocated to a stream of traffic • Interval - part of cycle when indications do not change • Offset - time lapse between green @ successive intersections • Change & clearance interval - Total time in seconds for yellow & all-red signal indications • All-red interval - when display is red for all directions

  18. Two-Phase Signal • Phase (A) • East-West Through Movement has Right-of-Way • Phase (B) • North-South Through Movement has Right-of-Way

  19. Two-Phase Signal: Phase (A)

  20. Two-Phase Signal: Phase (B)

  21. Four-Phase Signal • Phase A • East-West Left Turn Movement has Right-of-Way • Phase B • East-West Through Movement has Right-of-Way • Phase C • North-South Left Turn Movement has Right-of-Way • Phase D • North-South Through Movement has Right-of-Way

  22. Four-Phase Signal: Phase (A)

  23. Four-Phase Signal: Phase (B)

  24. Four-Phase Signal: Phase (C)

  25. Four-Phase Signal: Phase (D)

  26. Reduction in ConflictsDue to Traffic Signal No Signal2-Phase4-Phase Crossing Conflicts 16 4 0 Merge Conflicts 8 8 8 Diverging Conflicts 8 8 4

  27. Example 1 A section of a major highway has a speed-flow relationship of the form: q = au2 + bu It is known that the capacity is 2925 veh/hr and the corresponding space-mean speed of traffic is 30 mph. Determine the speed when the flow is 1400 veh/hr and the free-flow speed. 

  28. Example 1 - Solution @ qm = 2925 veh/hr, um = 30 mph @ qm, dq/du = 0 dq/du = 2aum + b = 0 (2)(a)(30) + b = 0 ……………... [1] qm = aum2 + bu 2925 = (a)(30)2 + (b)(30) …….. [2]

  29. Example 1 - Solution Solving for a & b  a = -3.25 & b = 195.00  q = -3.25u2 + 195u @ q = 1400 veh/hr, 1400 = -3.25u2 + 195u Solving for u  u1 = 8 veh/hr & u2 = 52

  30. Example 1 - Solution @ uf, q = 0  0 = -3.25uf2 + 195uf Solving for uf uf = 60 veh/hr OR uf = 2um = (2)(30) = 60 veh/hr

  31. Example 2 A section of a major highway has the following flow-density relationship: q = 42k-0.56k2 What is the capacity of the highway section, and the speed when the highway is at one quarter of its capacity.

  32. Example 2- Solution @ Capacity, q = qm , k = km, and u = um @ qm, dq/du = 0 dq/du = 42 - 1.12km = 0  km = 42/1.12 = 37.50 veh./mile Capacity = qm = 42km – 0.56km2  Capacity = qm = 787.5 veh./hr.

  33. Example 2- Solution @ One-quarter of capacity, q = qm /4 = 196.875 veh./hr. q = 196.875 = 42k – 0.56k2 0.56k2 - 42k + 196.875 = 0 Solving for k values,  k1 = 5 veh./mile OR k2 = 70 veh./mile

  34. Example 2- Solution @ q = 196.875 veh./hr. & k1 = 5 veh./mile, Speed = u1 = q/k1 = 39.375 mph OR @ q = 196.875 veh./hr. & k2 = 70 veh./mile, Speed = u2 = q/k2 = 2.8125 mph

  35. Quiz # 6 • Discuss briefly all the cases of traffic delay • Discuss briefly all the types of traffic volume counts

More Related