Physics & Astronomy HEP Electronics

1. Physics & AstronomyHEP Electronics TIM Interfaces to ROD Crate Components ATLAS SCT TIM FDR/PRR 28 June 2004 Matthew Warren John Lane, Martin Postranecky Interfaces to ROD Crate Components - Matt Warren

2. Overview • TIM located in center of ROD crate (slot 13) for optimal signal paths. • Sends Clock and Control signals over a custom J3 backplane. • Receives TTC Signals into front-panel via optical fibre. ROD Crate TIM! RCC ROD/ BOC 1-8 ROD/ BOC 9-16 Interfaces to ROD Crate Components - Matt Warren

3. TIM Connections Overview ROD (Read-Out Driver) RCC ROD Crate Controller ROD (Read-Out Driver) ROD (Read-Out Driver) ROD (Read-Out Driver) ROD (Read-Out Driver) ROD (Read-Out Driver) ROD (Read-Out Driver) ROD VME ROD (Read-Out Driver) ROD (Read-Out Driver) ROD (Read-Out Driver) ROD (Read-Out Driver) ROD (Read-Out Driver) ROD ROD (Read-Out Driver) ROD Read-Out Driver TIM-OK BOC BOC BOC BOC TIM TTC Interface Module Signals Busses BOC FP/PO Resets BOC BOC TTC (optical) BOC BOC BOC BOC BOC Front-End Modules Clock & Control (optical) BOC BOC BOC BOC Back Of Crate ROD Crate Busy ROD Busys NIM/ ECL Signals (48/BOC) Clocks Fanout MRMW v1.0 17-06-04 Interfaces to ROD Crate Components - Matt Warren

4. ROD-Crate-Controller Interface • Standard VME Slave • A24/A32 • D16 • D32 (top word unused) • Preset or Geographical base-address RCC ROD Crate Controller TIM TTC Interface Module Interfaces to ROD Crate Components - Matt Warren

5. Back-Of-Crate Interface • TIM distributes the BC clock to the BOC • BOC feeds clock to ROD in same slot • To minimise Skew/Jitter: • point-to-point same length lines • differential signalling (PECL) BOC BOC BOC BOC BOC BOC BOC BOC BOC BOC BOC BOC BOC BOC BOC BOC Back Of Crate TIM Interfaces to ROD Crate Components - Matt Warren

6. Read-Out Driver Interface • TIM distributes 8 Control Signals to RODs • As TIM is in the middle of crate, there are 2 busses - left and right - terminated at ends. • TIM is can adjust phase of the signals to satisfy ROD’s setup and hold times. • Signal assignment is flexible • can be re-mapped in firmware ROD (Read-Out Driver) ROD (Read-Out Driver) ROD (Read-Out Driver) ROD (Read-Out Driver) ROD (Read-Out Driver) ROD (Read-Out Driver) ROD (Read-Out Driver) ROD ROD (Read-Out Driver) ROD (Read-Out Driver) ROD (Read-Out Driver) ROD (Read-Out Driver) ROD (Read-Out Driver) ROD ROD (Read-Out Driver) ROD FP/PO Resets TIM • Signals active for one clock period. • TIM introduces dead-time after its stand-alone signals to compensate for longer FE signals from the ROD. Interfaces to ROD Crate Components - Matt Warren

7. Control Signals Description • L1A – Level-1 Trigger Accept • ECR – Reset Event Counter (L1ID) • First L1A after ECR is zero • BCR – Reset Bunch Counter (BCID)- once per LHC orbit • BCID value is in the range 0 – 3563 with LHC orbit BCRs. • If no BCR occurs, BCID is 0 – 4095. • CAL – Calibration pulse command for front-end amplifiers • SID – Serialised Trigger ID - 24 L1ID + 12 BCID bits • STT – Serialised Trigger Type - 8 TType + 2 reserved bits • ID's have a single start bit, no stop bit • SID, STT values are independently queued before TX • FER – Reserved - could be a separate periodic reset signal • SPR – Spare Interfaces to ROD Crate Components - Matt Warren

8. ROD Busy/TIM-OK • ROD-Busy • Received by TIM from RODs. • point-to-point signal. • Active low, pulled high on TIM • So empty slots are not indicated busy. • TIM-OK • Bussed to all slots in crate. • Pulled down. • Asserted when selected TIM clock is good. ROD (Read-Out Driver) ROD (Read-Out Driver) ROD (Read-Out Driver) ROD (Read-Out Driver) ROD (Read-Out Driver) ROD (Read-Out Driver) ROD (Read-Out Driver) ROD ROD (Read-Out Driver) ROD (Read-Out Driver) ROD (Read-Out Driver) ROD (Read-Out Driver) ROD (Read-Out Driver) ROD ROD (Read-Out Driver) ROD Read-Out Driver TIM FP/PO Resets Interfaces to ROD Crate Components - Matt Warren