220 likes | 713 Views
COMPACT HIGH POWER LASER DAZZLER™ (CHPLD). INITIAL TRAINING PRESENTATION. TOPICS. Introduction 3-7 Warnings/Safety 8-9 Specifications 10 Nomenclature 11 Battery Replacement 12 On-Off Push Button 13 Intermittent Button Switch 13 Remote Switch Tail Module 14 Make Safe When Not In Use 15
E N D
COMPACT HIGH POWERLASER DAZZLER™(CHPLD) INITIALTRAINING PRESENTATION
TOPICS • Introduction 3-7 • Warnings/Safety 8-9 • Specifications 10 • Nomenclature 11 • Battery Replacement 12 • On-Off Push Button 13 • Intermittent Button Switch 13 • Remote Switch Tail Module 14 • Make Safe When Not In Use 15 • Delrin Fixture 16 • Diffuser 17 • Cleaning 18-19 • Tips 20 • Questions 21
CHP LASER DAZZLER™ A Portable, Non-Lethal, Eye-Safe, Multi-Purpose Device Effective Both Day and Night
CHP LASER DAZZLER™ • It is the most rugged/powerful/compact laser device available that is suitable for this purpose • The CHPLD engages the target in a wall of green laser (532nm) light, which disorients and distracts the subject • This is accomplished by overloading the optic nerve rendering the subject nearly sightless for a short period of time – there is no doubt the individual will see the CHPLD, even in bright sunlight at 200 meters
CHP LASER DAZZLER™ • Specifically designed for applications where gaining the instant attention of individuals in varying light conditions including clear, bright sunny days is critical • IDEAL FOR CONVOY AND ENTRY CONTROL OPERATIONS • Immediate recognition by approaching vehicles or pedestrians which avoids the use of lethal force due to confusion or unseen /unrecognized hand signals
Drivers approaching a convoy or checkpoint may not see hand signals or realize they are entering a restricted/danger zone CHPLD at 100 yards – bright daylight They cannot fail to see the CHPLD even if distracted by traffic, sunlight, pedestrians, or other activities
OTHER USES • Mark your position and identify friendly units at long distances • Distraction & disruption of hostile groups • Counter sniper • Block line of sight when approaching target • Counter surveillance Mounted on Tripod Front view showing 4 lasers
WARNINGS/SAFETY • Laser Dazzlers™ are non-lethal devices, HOWEVER, with the potential for permanent eye damage if used improperly the CHPLD should always be TREATED LIKE A LOADED WEAPON • DO NOT point this device at any person unless it is operationally required • The user is solely responsible for the safe operation of the CHPLD and for adhering to the instructions and warnings provided • DO NOT look at the CHPLD thru optical devices such as binoculars or telescopes • This device has sufficient energy densities to cause irreversible eye damage and or permanent blindness if used on a subject at close distances or reflected onto a subject’s eyes from a highly reflective surface
WARNINGS/SAFETY • DO NOT use on subjects at distances closer than 20 meters or reflect back on subjects at distances equivalent to 20 meters or closer without the holographic diffuser installed • DO NOT use on subjects at distances closer than 3 meters or reflect back on subjects at distances equivalent to 3 meters or closer with the with the holographic diffuser installed • The CHPLD is powered by lithium sulfur dioxide primary batteries and are therefore NOT RECHARGEABLE • DO NOT attempt to charge the battery pack. Any attempt to do so is dangerous
SPECIFICATIONS • 500 Milliwatt, 532nm (green) flashing laser • Overall length - 11 inches • Maximum diameter - 2.5 inches • Powered by lithium sulfur dioxide primary batteries • BATTERIES ARE NOT RECHARGABLE • Safe Ranges • Minimum eye safe range – 20 meters (Without holographic diffuser) • Minimum eye safe range – 3 meters (With holographic diffuser) • Maximum effective range: • 200 meters – bright sunlight • 2 kilometers – night • Construction: • Anodized aluminum • Weight – 2.0 lbs. • Weight as shown – 2.6 lbs. • All parts produced in the USA • Operating Conditions: • All-weather, general purpose and water tight
NOMENCLATURE Aiming Device DELRIN FIXTURE CHPLD
BATTERY REPLACEMENT • Unscrew tail module • Install battery positive end first • Rotate battery for best fit when installing • Check to confirm O-Ring (3) is still in place • DO NOT over tighten switch module
ON-OFF PUSH BUTTON • Push and release to turn on • Push and release again to turn off • Operate laser by push and release of intermittent button switch INTERMITTENT BUTTON SWITCH
REMOTE SWITCH TAIL MODULE • This module contains an electronic switch circuit powered by a capacitor which is charged by the battery pack when the laser is OFF • INITIAL CHARGE REQUIRES 4 MINUTES • The laser can be operated for 45 minutes continuously from the initial charge • When the laser is turned off the capacitor is fully charged • The cable connectors for this module are male/female pin type • Mate each connector • Secure by gently rotating the locking collar until it engages the mating part • Rotate clockwise approximately 1/8 of a turn to lock in place
MAKE SAFE WHEN NOT IN USE • Integral On-Off Push Button Switch Module • Unscrew ¼ to ½ turn • Press button to ensure laser does not fire • If necessary unscrew additional ¼ turn increments until laser will not fire • Remote Switch TailModule • Disconnect cable connectors • DO NOT unscrew module since the capacitor charge may dissipate and the initial charge time (4 minutes) would be required to operate the laser • Press button switch to ensure laser does not fire • Long Period of Non-use • Remove battery pack • Reinstall Tail Switch Module to prevent dirt and moisture from entering the device
DELRIN FIXTURE • The laser is provided in the Delrin Fixture and sighted to the red dot reticule scope. • An intermittent on/off button is built into the fixture and is armed by connecting the cable on the Tail Module to the mating connector on the Delrin Fixture • Secure by gently rotating the locking collar until it engages the mating part • Rotate clockwise approximately 1/8 of a turn to lock in place
DIFFUSER • Adding the provided Holographic Diffuser reduces the minimum eye safety distance from 20 meters to only 3 meters • Unscrew window module • Remove white washer • Place diffuser on window • Reinstall white nylon washer • Reinstall module on device
CLEANING • Remove the laser from the Delrin Fixture • Disconnect cable • Remove the Tail Module • Loosen the 6-32 set screws • Slide the laser forward • Make sure not to lose the O-Ring (3) • It is not necessary to remove the set screws • To reinstall just reverse the process
CLEANING • Window • With device front facing down unscrew window module • Remove white nylon washer • Turn module over and clean surface underneath • The window & O-Ring will drop out • Clean window with appropriate cleaner such as Windex® sprayed onto a cloth • Reinstall in reverse order • Make sure O-Ring (1) is in the groove • Make sure O-Ring (2) is still on the laser body • CHPLD • Wipe with damp cloth and or a cleaner such as Windex® sprayed onto the cloth • DO NOT immerse in water or cleaning fluids • NO OTHER FIELD DISASSEMBLY OF THE LASER OTHER THAN AS DESCRIBED ABOVE IS PERMITTED. DOING SO WILL DAMAGE THE DEVICE AND VOID THE WARRANTY
TIPS • TIPS FOR EFFECTIVE USE • Individuals or groups: Aim at the center of the chest then raise the beam to eye level for a very short period of time – repeat as necessary • Vehicles: Aim at the center of the windshield then move to the drivers side for a very short period of time – repeat as necessary
QUESTIONS ? Easily seen at 1 mile in bright sunlight