1 / 15

Chapter 7 ( thompson ) Lines and interconnections

Chapter 7 ( thompson ) Lines and interconnections. How do we send signal? . We need “Transducers” Analog vs. Digital Connections What’s the difference? What should we consider when transferring data? The ________distance from one point to the next is usually the best.

theta
Download Presentation

Chapter 7 ( thompson ) Lines and interconnections

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Chapter 7 (thompson)Lines and interconnections

  2. How do we send signal? • We need “Transducers” • Analog vs. Digital Connections • What’s the difference? What should we consider when transferring data? • The ________distance from one point to the next is usually the best. • Meaning: Length of cable, conversion, processing through gear

  3. TRANSFORMERS

  4. TRANSFORMERS • Transforms electrical energy from one circuit to another • A transformer has COILS which create a varying magnetic flux. The windings determine the “RATIO” • Transformers are useful in audio because they can change the impedance of a signal. i.e. A microphone going to a mixer

  5. More on TURNS RATIO • There is a PRIMARY and SECONDARY wiring in every transformer • A transformer can step UP or DOWN depending on the ratio. • Voltage and current is directly related to the ratio Thompson p. 156-157

  6. Unbalanced Lines • What are some unbalanced connections? • What’s the biggest issue with them? • Multiple pieces of gear connected together can cause “Earth Loops” or “ground loop hum” at 50Hz

  7. Balanced Lines • What kinds of connections are balanced? • They reject interference better • Known as CMR or “Common Mode Rejection” • Think of it as one + and one – canceling each other out with transformers on each end. • Accepts “Differential” signal but rejects “Common Mode”

  8. XLR Review • Hot (+) Cold (-) and Ground • Pin 1 = Ground (Screen) • Pin 2 = + Hot • Pin 3 = - Cold • Balanced to unbalanced can still avoid a “Earth (Ground) loop” but cannot reject interference. • TRS has the same connections (You can convert between the two) Thompson p. 164

  9. CABLES • CONDUCTOR: Sends signal • INSULATOR: Separates signals, prevents crosstalk • SHIELD: Eliminates noise & Interference

  10. Multicore Cables (ex. Snake) • Ability to send multiple analog inputs and outputs over the same cable • Twisted cables help reject interference • Try to avoid “Crosstalk”: When signals interfere with each other • How can digital cables be advantageous in situations where multiple channels are needed in one connector?

  11. DI Boxes • Direct Injection Boxes • Converts Unbalanced inputs to a Balanced output • Another way to look at it: Converts hi-impedance to low-impedance • Can be active or passive • See figure 12.14 • Generally used on instrument cables

  12. Splitter Boxes • Splits one signal into two • Required to maintain a suitable impedance for the microphone • There is ONE primary winding and TWO secondary windings • This creates a ratio that loses 3dB of signal • BUT it also halves the impedance, so there is not difference unless the impedance gets too low.

  13. PATCHBAYS • Also known as “Jackfields” • Easy way to ROUTE equipment without having to access the specific piece • Usually 24 sockets in a row • “TT” Tiny-Telephone connections • Balanced, so they maintain signal integrity • They usually are NORMALLED to a certain piece of gear

  14. 4 Connection Types • Top row is OUTPUT, bottom row is INPUTS • Open: Never makes a connection between the top and bottom unless plugged in • Half-Normalled: Keeps the signal but allows you to plug into the OUTPUT • Fully-Normalled: Any connection will disturb the normalled connection. • http://www.whirlwindusa.com/pre01.html

  15. DISTRIBUTION AMPLIFIERS • Allows for distribution of one input to a number of outputs • They have independent level control and isolation • Every output is not affected by connections made to others • This differs from a SPLITTER in that sense… it is also strictly for amplification.

More Related