'Finite element model' presentation slideshows

Introduction to Finite Element Methods

Introduction to Finite Element Methods. Need for Computational Methods. Solutions Using Either Strength of Materials or Theory of Elasticity Are Normally Accomplished for Regions and Loadings With Relatively Simple Geometry

5.3k views • 78 slides

UCSD/General Atomics Design Project: Aeroelastic Wing Enhancement

UCSD/General Atomics Design Project: Aeroelastic Wing Enhancement. Jose Panza, Project Sponsor Dr. James D. Lang, Project Advisor Jonquil Urdaz, Team Leader Sean Summers Steve Ringel Jorge Mendoza. Presentation Outline:.

688 views • 46 slides

FEMCI Workshop at GSFC 17 May 2001

FEMCI Workshop at GSFC 17 May 2001 STOP Analysis & Optimization of a very Low-Distortion Instrument HST WFC3 Case Study by Cengiz Kunt Swales Aerospace, Inc. HST. WFC3. OUTLINE.

564 views • 38 slides

Concrete Institute of Australia Soil-Structure Interaction Seminar Sydney March 2007

Concrete Institute of Australia Soil-Structure Interaction Seminar Sydney March 2007. Design of Buried Arch Tunnels Under High Fills Doug Jenkins Interactive Design Services. Overview:. Influence of high fills on structural actions Design of foundation structures for high vertical loads

641 views • 36 slides

743 views • 33 slides

Ferroelectric Superlattices for Use in Non-linear Transmission Lines

Ferroelectric Superlattices for Use in Non-linear Transmission Lines. Robert James Sleezer Research Proposal Defense 16 December 2008. Acknowledgements. Gregg Salamo , Advisor Jerzy Krasinski , Masters Advisor and Committee Member Laurent Bellaiche , Committee Member

504 views • 33 slides

Philip Hall Proudman Oceanographic Laboratory Liverpool

Variability of Internal Tides in a Three-Dimensional, Baroclinic, Finite Element Model of the Shelf-Edge. Philip Hall Proudman Oceanographic Laboratory Liverpool. Acknowledgements: Alan Davies, Jiuxing Xing, Eric Jones, Sarah Wakelin, John Huthnance(Liverpool) ICOM team

475 views • 33 slides

Fatigue calculations on benchmark tasks according to ASME code, experiences, results

411 views • 28 slides

372 views • 25 slides

A Project Presentation for Applied Computational Fluid Dynamics By Reni Raju

Finite Element Model of Gas Flow inside a Microchannel. A Project Presentation for Applied Computational Fluid Dynamics By Reni Raju. MECH - 523. Objectives. Develop a 2D Finite Element Model for gas flow inside a microchannel. Develop FE formulation for N-S equations.

406 views • 24 slides

Predicting fatigue damage in intact and restored teeth

Predicting fatigue damage in intact and restored teeth. Sam Evans Sam Smith School of Engineering, Cardiff University PO Box 925, The Parade, Cardiff CF24 0YF. Introduction. Tooth fracture or cracking is a common cause of clinical failure The cause of this problem is not well understood

371 views • 24 slides

The Craig-Bampton Method

The Craig-Bampton Method. FEMCI Presentation Scott Gordon May 6, 1999 Topics: 1) Background 2) Theory 3) Creating a C-B Model 4) Load Transformation Matrices 5) Verification Appendix: Sample FLAME scripts. Background. Who is Craig Bampton?

1.23k views • 16 slides

Study of Heat Flux in a Thin Silicon MEMS Wafer with Coolant and Air Filled Regions A Finite Element Model (FEA) using

Study of Heat Flux in a Thin Silicon MEMS Wafer with Coolant and Air Filled Regions A Finite Element Model (FEA) using flexPDE. Craig E. Nelson - Consultant Engineer. Goal for the Numerical Study

277 views • 13 slides

A Modeling Study to Determine the Effectiveness of an Energy Recovery Ventilator (ERV)

A Modeling Study to Determine the Effectiveness of an Energy Recovery Ventilator (ERV). R. Pastor 1 , E. Gutierrez-Miravete 2 and N. Lemcoff 2 1 General Dynamics Electric Boat 2 Rensselaer Polytechnic Institute Hartford. Background. Energy Recovery Ventilator

290 views • 13 slides

Liquid Argon in a Large Tank --- Some Thermodynamic Calculations Zhijing Tang November 4, 2004

Liquid Argon in a Large Tank --- Some Thermodynamic Calculations Zhijing Tang November 4, 2004. Questions . Heat leak Heat leak from chimney Convection flow Temperature distribution Force on wire Flow from surface downward . Liquid Argon in Big Tank.

438 views • 12 slides

200 views • 11 slides

Study of Deformation due to Thermally Induced Stress in a Water Cooled Plastic Injection Mold

Study of Deformation due to Thermally Induced Stress in a Water Cooled Plastic Injection Mold A Finite Element Model (FEA) using flexPDE. Craig E. Nelson - Consultant Engineer. Goal for the Numerical Study

219 views • 10 slides

Activity 3: Characterization and Simulation: Cell Environment

Activity 3: Characterization and Simulation: Cell Environment. Peter M. Anderson, Materials Science Heather Powell, Materials Science/Biomedical Engineering Samir Ghadialli, Biomedical Engineering Gregory Lafyatis, Physics Supported Graduate Student: Yanyi Xu

158 views • 6 slides

Pre- and Post-processing for the Finite Element Model of a Cornea Progress Update 1

Pre- and Post-processing for the Finite Element Model of a Cornea Progress Update 1. Advisor: Craig Foster Civil and Materials Engineering University of Illinois at Chicago Daniel Kang Lindblom Math and Science Academy July 7, 2011. Background. Stroma. Pre-processing.

198 views • 6 slides

Kyle White Research Undergraduate Faculty Advisors; Dr. Damon Fick, Dr. Michael West

157 views • 1 slides