1 / 21

Composite Filament Winding Machine P09226

Composite Filament Winding Machine P09226. Detailed Design Review Christofer Brayton Shijo George Alex Sandy Tiago Santos Daniel Weimann. Background. Why composite tubing? High Strength Light Weight High creep and fatigue performance Chemical and corrosion resistance.

ricerobert
Download Presentation

Composite Filament Winding Machine P09226

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Composite Filament Winding Machine P09226 Detailed Design Review ChristoferBrayton Shijo George Alex Sandy Tiago Santos Daniel Weimann

  2. Background Why composite tubing? High Strength Light Weight High creep and fatigue performance Chemical and corrosion resistance

  3. Filament Winding • The process by which a continuous strand of impregnated fibers is wound onto a mandrel with specific fibers’ orientation which is controlled by computer. • Once resin has cured, mandrel is removed

  4. RIT First Generation Filament Winding Machine Capabilities • Produce tubes of limited dimensions • Simple to operate • Maintain tension every time • Limited range of orientation angles • Able to be expanded upon • Primary Goals • Learning Experience • New technology to RIT and students involved • Create simple but bulletproof machine

  5. Raw Material Processing Steps1. Preheat ADIPRENE K 1 gallon cans to 50°C (122°F). 1 gallon can requires approximately 8 hrs to reach equilibrium temperature.2. Apply mold release to mold. Preheat Mold to 115°C (240°F)3. Pour the entire gallon of ADIPRENE K into a can and stir with a spatula in a “figure-eight” motion to ensure homogeneity. Add any additional ingredients at this time.4. Fill the hot mold by pouring ADIPRENE K down the side of the mold. Pouring down the side of the mold will reduce air entrapment.5. Place filled mold into the 115°C oven.6. Allow material to reach 115°C for curative de-blocking and complete curing. De-mold times for small parts (0.25lb) require approximately 20 minutes.7. Optional - Post Cure for 16 hours at 115°C for optimum properties • Torayca M40J Carbon Fiber • Readily available/Free • Adiprene K X028 • Readily available/Free

  6. Creel

  7. Tension

  8. Impregnation System

  9. Impregnation System

  10. Mandrel

  11. Relative Speeds • Relative Speeds control the angle at which fibers lay onto the mandrel θ is the fiber winding angle (°) r is the radius of the mandrel Nm is the speed of the mandrel [RPM] Vc is linear velocity of the feed eye P is the pitch of the rack NS is the pinion speed [RPM]

  12. Relative Speeds

  13. Motors - Mandrel Τ is the torque applied [N-m] F is the force applied [N] r is the radius on which the force is applied [m] m is the mass of applied load [kg] g is the acceleration of gravity [9.81 m/s2]

  14. Motors – Feed Eye TL is the torque applied F is the force applied D is the diameter of the pinion η is the efficiency of the gear train (assumed to be .9) i is the Gear Ratio of the rack and pinion (1.5 in/rev)

  15. Motor Selection

  16. Controls

  17. Computer / User Interface B (+) B (+) RS-485 IN A (-) RS-485 IN A (-) IGND IGND SW2 SW3 Input 1 Input 1 SW6 SW11 Input 2 Input 2 CHB SW7 CHB SW12 ON/OFF +5V ON/OFF +5V SW8 V1 CHA SW13 V6 CHA Direction 5VDC Direction 5VDC INDEX SW9 INDEX SW14 Hard + GND Hard + GND SW10 SW15 0 Hard - 0 Hard - Output 1 Output 1 Feed Eye Mandrel VIN VIN V2 V7 12-24Vdc GND 12-24Vdc GND 23MDSI SERIES 23MDSI SERIES SW5 D1 0 R1 0 1k V4 SW MAG-SPST 3.3Vdc LED SW1 D2 R2 1k V5 SW MAG-SPST 3.3Vdc LED SW4 D3 R3 1k V3 SW MAG-SPST 3.3Vdc LED 0 Controls

  18. BOM

  19. BOM

  20. BOM

More Related