1 / 13

MULTIPURPOSE DIGITAL CDMA FM REMOTE CONTROLLER

COMMUNICATION ELECTRONICS. MULTIPURPOSE DIGITAL CDMA FM REMOTE CONTROLLER. FIRDOUS KAMAL MIZAN MIAH. EE – 513 4/19/2005. OVERVIEW. Project description - Goals and objectives Functional units Transmitter and Receiver Circuit description

phiala
Download Presentation

MULTIPURPOSE DIGITAL CDMA FM REMOTE CONTROLLER

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. COMMUNICATION ELECTRONICS MULTIPURPOSE DIGITAL CDMA FM REMOTE CONTROLLER FIRDOUS KAMALMIZAN MIAH EE – 513 4/19/2005

  2. OVERVIEW • Project description • - Goals and objectives • Functional units • Transmitter and Receiver • Circuit description • FSK: Modulation, Demodulation; Filters and Amplifiers • DATA encoding • PIC 16F767 mcu data processing • Time management and costs • Performance

  3. PROJECT DESCRIPTION • House appliances such as heater, lights, oven, electrical outlets, security gates etc. do not have standard remote controllers. • Common consumer remote controllers have distance and directional limitations. • RF implementation is difficult due to noise issues and because RF bandwidth is expensive. • Security issues and cross connection between users are other concerns. • Our goal - hardware implementation of CDMA FM remote controller for household appliances.

  4. OBJECTIVES • One transmitter and two receiver units. • Each receiver has one switch and two BCD digits. • Inputs are entered using a (4x4) keypad. • CDMA encoding is implemented for the two receivers. • FSK transmission and reception of data – Pulse length variation for high and low bit. • 8 – bit PIC16F767 microprocessor used for data encoding and decoding.

  5. FUNCTIONAL UNITS

  6. NJM 2211D – MONOLITHIC PLL CHIP FSK MODULATOR – VCO OSCILLATOR CIRCUIT DESCRIPTION: TRANSMITTER The VCO unit of the PLL can be used to generate a square wave of a desired frequency. The lock detector filter is then internally grounded with ref. Vout f0 = 1 / (R0 C0) Operating f0 designed around 100kHz Tracking bandwidth is given by: f / f0 = R0 / R1 Designed for 10% bandwidth

  7. NON-INV AMPLIFIER (HIGH ZIN) PLL FSK DEMODULATOR 2nd ORDER ACTIVE FILTER (LOW PASS) CIRCUIT DESCRIPTION: RECEIVER • RF and CF provides a low pass data filter network. C1 and R1 provides feedback and loop damping. • For the low-pass filter: • 3dB point = 1/ 2 RC • = 160kHz • Non-inverting amplifier provides high input impedance and a closed loop gain of around 2.

  8. Start Sequence Channel A-011100 3ms 5ms 7ms 5ms 6ms 2ms 3ms 5ms 6ms f1 f1 f1 f2 f2 2ms 2ms 2ms DATA ENCODING Pulse Width variation is used to determine a binary 1 or 0. Binary 1 is a high of 5ms followed by a low of 3ms. Binary 0 is a high of 3ms followed by a low of 3ms. Only 8 bits were retrieved by the receiver following the channel code. Thus if a bit was missed, the error could be corrected by implementing a code correcting algorithm. Furthermore, the data can be sent multiple times to reduce chances of error.

  9. TIME MANAGEMENT

  10. PROJECT COST • Cost estimates • Transmitter unit: $ 25 • Receiver units: $ 20 each • Total project cost: $ 85 including solder boards • Hours spent: 170 hrs (aprx) by each group member • Estimated manufacturing cost for each unit with a 20 x 4 line LCD display will be under $10 if smt or soic components are used with blow soldering on pre-printed circuit boards. • Sold for $25 will beat any commercially available unit currently on the market by more than $30 accounting for design costs by engineers. We have assumed around 10,000 units for mass production.

  11. PERFORMANCE • All of our units were tested and demonstrated functional within the allocated time period. • We have constructed and implemented our own FSK receiver and transmitter and completed the system integration by the project demonstration date. • The units are powered by 9V batteries. • Wireless transmission is achieved for a distance of 10cm. During testing we successfully transmitted a distance of 20mm through a partex board. • On a testing trial of 50 times no errors (cross connection) between the two receiving units are observed. • The total project cost is within the proposed budget.

  12. FURTHER IMPROVEMENTS • We down-shifted our carrier frequency from about a MHz to 100kHz to implement a frequency upconverter. • The 1MHz FSK generator implemented with a 555 timer was tested functional. • However, most high frequency components are surface mount and lacking the facilities and time, we were unable to utilize a better frequency range. • As further improvements, a higher frequency carrier will improve range (up to 50 yards with at 100MHz) with no significant increase in power. • Multiple users (receiver units) can be implemented to the current system by simply changing the channel code for each unit for the PIC mcu. • Some error bits were noticed during testing (within the same channel). This can be corrected by implementing Hamming or similar error detection/correction procedures.

  13. QUESTIONS & COMMENTS ?

More Related