1 / 19

HT46 A/D Type MCU Series

HT46 A/D Type MCU Series. HT46R25* (OTP) HT46C25* (Mask). 16Kx16. HT46R24 (OTP) HT46C24 (Mask). 8Kx16. Program Memory. HT46R23 (OTP) HT46C23 (Mask). 4Kx15. HT46R22 (OTP) HT46C22 (Mask). 2Kx14. * Under development, available in 4Q, 2004. 576. 64. 192. 384.

parson
Download Presentation

HT46 A/D Type MCU Series

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. HT46 A/D Type MCU Series HT46R25* (OTP) HT46C25* (Mask) 16Kx16 HT46R24 (OTP) HT46C24 (Mask) 8Kx16 Program Memory HT46R23 (OTP) HT46C23 (Mask) 4Kx15 HT46R22 (OTP) HT46C22 (Mask) 2Kx14 * Under development, available in 4Q, 2004 576 64 192 384 Data Memory (Byte)

  2. HT46 A/D Type MCU Series

  3. RISC Architecture Direct and Indirect Addressing mode. Total 63 instructions. Table read function. Maximum 16 stack ( by product) Operating Voltage: Fsys = 4Mhz, 2.2~5.5v Fsys = 8Mhz, 3.3~5.5v Idd : 2mA (tpy.) (5V, 4MHz, Xtal, ADC disable) Istb : 1uA (max.) (WDT, RTC disabled). -40oC~85oC Operating temperature.(Industrial grade) Features of A/D Type HT46 Series

  4. I/O with pull high function. Port A with wake up function. Timer function Watch dog function Halt and wakeup for low power consumption. I2C interface PFD driver output. On-chip crystal and RC oscillator LVR for Brown-out protection. Multi-channel 9 or 10-bit A/D converter Pulse Width Modulator output. Peripheral Feature

  5. Block Diagram

  6. Program Memory Map

  7. Special Purpose Data Memory

  8. General Purpose Data Memory • 2 banks of Data memory in HT46X24 • Each one has 192x8 bytes (total 384 bytes). • Need to use BP(bank pointer in special RAM) to select Bank0 or Bank1 data memory. • BP=0 Access Bank0 data. • BP=1 Access Bank1 data. • Only use MP1 by Indirect Addressing mode to access.

  9. PWM • PWM is Pulse Width Modulator. • There are two modes 6+2 or 7+1 selected by configuration. • User can change the frequency duty software • by writing data to PWM0~PWM3 special data register. • PWM function can be controlled On/Off by software. • Enable PWM output : SET PD0 • Disable PWM output : CLR PD0

  10. PWM 6+2 Mode

  11. PWM 7+1 Mode

  12. Analog to Digital Converter • The HT46 series have a 9 or 10-bit ADC. • ADC can be disabled by software. • Max. 4 or 8 channels can input to the ADC. • Channels set in ADCR by software • ADC channels are pin-shared with Port B. • As ADC input or Port B set in ADCR by software • Input range is from 0 to VDD. • Min. ADC clock period is 1us. • ADC sampling time is 32 ADC clocks. • ADC convert time is 76 ADC clocks. • Max. INL ± 1 LSB.

  13. ADC Convert Data Register • ADRL/ADRH are two registers to store the ADC convert data.

  14. A/D Convert Control Register

  15. A/D Convert Clock Source Register

  16. A/D Convert Timing Diagram

  17. I2C Bus Interface • I2C bus is a bidirectional 2-wire serial interface. • SCL : serial clock pin. • SDA : serial data pin. • I2C output is of open drain . An external pull high resistor is needed. • HT46 series I2C bus is only operates in Slave mode. For Master mode, user can implement by software.

  18. I2C Registers • I2C Slave Address Register - HADR • I2C Input/Output Data Register – HDR • I2C Control Register –HCR. • I2C Status Register – HRS. • Using HT46 serial I2C Slave function, user can only need to set some flags and polling some status flags. Then, I2C bus can work.

  19. Configuration Options

More Related