1 / 21

CN2668 Routers and Switches

CN2668 Routers and Switches. Kemtis Kunanuraksapong MSIS with Distinction MCTS, MCDST, MCP, A+. Agenda. Chapter 5: Router and IOS Basics Exercise Quiz. Benefits of Routing. Routers provide Packet filtering Connections between local networks Traffic control

nasia
Download Presentation

CN2668 Routers and Switches

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. CN2668Routers and Switches Kemtis Kunanuraksapong MSIS with Distinction MCTS, MCDST, MCP, A+

  2. Agenda • Chapter 5: Router and IOS Basics • Exercise • Quiz

  3. Benefits of Routing • Routers provide • Packet filtering • Connections between local networks • Traffic control • Wide area network (WAN) connections • Routers operate at the Network layer of the OSI reference model • Because of Network layer addressing, routers can direct packets to both local and remote segments

  4. Cisco Router User Interface • Cisco Internetwork Operating System (IOS) • Provides a command-line interface (CLI) • You can access a router in several different ways • Console port (also known as the console) • Auxiliary port (AUX) • Virtual terminals (VTY) • Trivial File Transfer Protocol (TFTP) server • See Figure 5-1 on Page 119

  5. System Configuration Dialog • If the router has not been configured previously, or if the startup file has been erased • The Cisco IOS will prompt you to run the initial configuration dialog after the router boots • You also can type Setup to configure as well • A series of prompts that guide you through the initial configuration for the router • If IOS 12.0, you have two setups • Basic management • Extended setup

  6. User Interface • The initial prompt: • The host name of the router followed by the greater than symbol (>) • Default: router> • User EXEC mode (User mode) • When the prompt displayed is the greater than symbol • User mode does not allow you to configure the router only to check status and review settings

  7. User Interface (continued) • The question mark activates context-sensitive Help on the Cisco router • Privileged EXEC mode • To enter privileged EXEC, you can type the enable command at the user mode prompt • Next, you may be prompted for a password • Greater than symbol (>) changes to a pound sign (#)

  8. User Interface (continued) • The question mark activates context-sensitive Help on the Cisco router • Privileged EXEC mode • To enter privileged EXEC, you can type the enable command at the user mode prompt • Next, you may be prompted for a password • Greater than symbol (>) changes to a pound sign (#)

  9. User Interface (continued) • In Privileged EXEC mode • Setup command will cause the router to enter the system configuration dialog • Copy configurations can be copied from TFTP servers to the router and therefore change the router configuration • Erase configuration files as well as the entire IOS can be erased

  10. Configuration Modes • Global configuration mode • Accessed by typing configure terminal at the enable mode prompt • Interface configuration mode • Allows you to configure the Ethernet and serial interfaces on your router • Line configuration mode • Allows you to configure the virtual terminals, console, and AUX lines that let you access the router

  11. Configuration Modes (continued) • Typing exit will take you back one level • Typing end or pressing the Ctrl+Z keys will take you all the way back to the enable prompt • Abbreviated commands • Such as conf t, en, shru • The router will show you the point at which you entered an incorrect character

  12. Plethora of Passwords • 5 passwords you can set • Enable • Enable Secret • Console • Aux • Virtual Terminal (VTY) • Use service password-encryption if you want to encrypt all passwords

  13. Plethora of Passwords • Enable Password and Enable Secret Password configuration • You can set both passwords from the global configuration mode prompt • You can type no enable secret and no enable password at the global configuration mode prompt • To remove the enable secret and enable passwords

  14. Plethora of Passwords (continued) • Setting Line passwords • You can set passwords for each line used to configure the router • Configure the console line password • Enter line con 0 • You can also configure passwords on the five virtual terminal lines that exist on every router • Enter line vty 0 4

  15. Enhanced Editing • The enhanced editing commands let you jump to the beginning or end of a command line • You can also jump forward or back, character by character, or word by word • You can turn off the enhanced editing features by typing terminal no editing at either the user EXEC or the privileged EXEC prompts • You can turn on terminal editing by typing terminal editing • See Table 5-3 on Page 129

  16. Command History • Command history • Allows you to retrieve previously typed commands • You can see up to 10 previously typed commands by typing show history • To modify the number of commands stored by the router, you can use the terminal command • Up to 256 previous commands • Type terminal history size n

  17. Configuring Router • Router host name • Default host name is router • To set the router host name, type hostname followed by the name that you want to set • Configure a banner • A banner is a message that you can configure to display each time someone attempts to log in to the router • Enter global configuration mode by typing config t • Then type bannermotd, followed by a space and a delimiting character

  18. Configuring Router (Cont.) • Configure an interface description • Use the description command • The interface description helps you remember which network the interface services • Use the clock set command in enable mode to configure the time • You must be in global configuration mode to configure the time zone • See Figure 5-14 on Page 132

  19. Router Components • ROM • Contains the bootstrap • Not modified during normal operations, but it can be upgraded with special plug-in chips • Flash memory (EPROM) • Contains the working copy of the current Cisco IOS • Is the component that initializes the IOS for normal router operations

  20. Router Components (Cont.) • NVRAM • Contain the startup configuration file for the router and IOS uses it during boot process • RAM/DRAM • Changes to the router’s running configuration take place in RAM/DRAM • Interfaces

  21. Assignment • Review Questions • 1 – 24 • Case Projects • 5 • Lab 5.1, 5.3 – 5.5

More Related