1 / 39

COLD BENDING RESEARCH NEEDS

COLD BENDING RESEARCH NEEDS. Courtesy S. Kozel. UNIVERSITY OF BALAMAND RESEARCH COUNCIL JUNE 23 rd , 2004. OUTLINE. MOTIVATION PROPOSED METHOD PREVIOUS WORK CURRENT WORK FUTURE WORK. Cut Curving. Flange. Flange. Flange. Scrap. Fit-Up. Pressure Applied During Fit-up. Web.

mahlah
Download Presentation

COLD BENDING RESEARCH NEEDS

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. COLD BENDING RESEARCH NEEDS Courtesy S. Kozel UNIVERSITY OF BALAMAND RESEARCH COUNCILJUNE 23rd, 2004

  2. OUTLINE • MOTIVATION • PROPOSED METHOD • PREVIOUS WORK • CURRENT WORK • FUTURE WORK

  3. Cut Curving Flange Flange Flange Scrap

  4. Fit-Up Pressure Applied During Fit-up Web Pressure Applied During Fit-up Flange Flange Fitting Jig

  5. Problems ? • - Costly because of excessive waste • - Too much scrap for sharp curvatures • - Used for mild curvatures (R  300m) • - Fit-up operation too complicated

  6. Heat Curving HEATED AREA

  7. Problems ? • - Trial and error process relying on uneven expansion/contraction. • - Takes time to heat and much longer to cool down. • - Results not known till AFTER cooling. • - If it is not right, process must be repeated. • - Ties up shop, slow and costly.

  8. 3-ROLLERS BENDING PINCHING ROLLER Courtesy AISC

  9. Bridges: Current Status ? • Not allowed by AASHTO, concerns: • - Cracking, Fracture • - Flange Upsets • - Dimples • - Web Crippling • No criteria is available • Depends on skill and knowledge of fabricators

  10. MIAMI METROMOVER PROJECT

  11. TAMPA STEEL TAMPA STEEL 1: Hydraulic jack (bot. flange) 2: Hydraulic jack (top flange) 3: Longitudinal arms 4: Steel plate 5: Clamps

  12. PROPOSED CONCEPT L 2 4 5 3 6 1 7 3 5 max = 4 2 6 x

  13. FULL-SCALE DEMO FULL-SALE DEMO

  14. Top Flange Bending S

  15. Bot Flange Bending 5 7 1: Jack 2: Head 3: Plate 4: Angle 5: Support 6: String Line 7: Stiffener 1 4 2 3 6

  16. FORMULATION • PARAMETERS: • - Load Frame Spacing S • - Bending Loads Ptf, Pbf • - Deflection  within span S • - Segment Length Li • - Number of Segments n • - Offsets S Li Ptf

  17. Comp. side Flange S = Lp LOAD FRAME SPACING (S) • Based on lateral bracing limit: • S = 14.4c for Grade 250 steel • S = 12.2c for Grade 345 steel • For unsymmetrical sections use ctf Load P Flange Width 2c

  18. BENDING LOADS (Ptf, Pbf) • From simple beam plastic load analysis: Top Flange: Ptf based on ttf, ctf Bot. Flange: Pbf based on tbf, cbf Constant P Fytfc c Fytfc c Mp = Fytfc2 S

  19. DEFLECTION  ctf cbf Ptf  Pbf Load P tf bf set  = cte = tf    bf ??? bf Plastic Hinge tf Set P = Pbf, Load in cycles m=tf/bf P  Pbf (not in this scope) S

  20. SEGMENT LENGTH Li 2Li tf S [m]   Constant   [m-1] [m+1] 2Li 2Li/S Radius R

  21. Length L nLi a a n n+1 2 4 5 3 1 Line of symmetry NUMBER OF SEGMENTS n Round-down to the nearest even integer adjust

  22. OFFSETS ii, ij 2 6 7 1 3 5 4 Load: 2 22 Load: 3 23 33 Load: 4 24 34 44 Load: 5 25 35 45 55 Load: 6 max 26 46 36 56 66

  23. FABRICATION AIDS (LOADS) Ptf =0.462.5152 = 260kN,Pbf =0.465252 = 1440kN P/tfc2(kN/cm3) G 400 G 345 0.46kN/cm3 G 250 S (cm) 215cm

  24. FABRICATION AIDS (Deformations) tf = 3.5/15 = 0.23cm,bf = 3.5/25 = 0.14cm G 400 G 345 round-up to 2 G 250 c (cm2) 3.5cm2 S (cm) S = 215cm S (m)

  25. FABRICATION AIDS (Multiple Load) G 400 Bot. Flange load /(S2/c)105 G 345 G 250 = (tf – bf)=0.09cm [/(S2/c)]105 = 4.9. 4.9 Px/tfc2/S (kN/cm2) S (m) R/c (cm/cm) 97 Px=975(25)2/215=1400kN (kN/cm2)

  26. FABRICATION AIDS (Segments) G 400 G 345 Li=0.25215=53.75cm n=(1200–215)/53.75= 18.3 Round-down to n=18. Li=(1200–215)/18= 55 cm G 250 Li/S cm/cm) 800 S (m) R/c (cm/cm)

  27. SUMMARY • - Development of a standardized cold curving procedure. • Relationships (loads vs. deformations), Fabrication Aids are now available. • - Limits are set on maximum strains (plastic) • Note: Residual stresses may be released by heat treatment

  28. Sen,R., Gergess,A. & Issa,C. “Finite Element Modeling of Heat-Curved I-Girders” ASCE Journal of Bridge Eng, Vol. 8, No. 3, May/June 2003,pp.153-161. • Gergess A. & Sen R. (2003). “Simplified Heat-Curving Analysis”. Journal of Transportation Research Board, No. 1861, Construction, pp. 101 - 114 • Gergess, A. & Sen, R. “Inelastic Response of Simply Supported I-Girders Subjected to Weak Axis Bending,” Proceedings of the International Conference on Structural Engineering, Mechanics and Computation, Cape Town, South Africa, Edited by A.Zingoni, Vol. I, pp 243-250, 2001. • Gergess, A. and Sen R. “Fabrication Aids for Cold Straightening Structural Steel Girders”. AISC, EngineeringJournal (in press), 2004. • Gergess, A. and Sen R. “Cold Curving Un-symmetric Un-stiffened Steel Girders, Journal of Constructional Steel Research, London, UK (in press), 2004. PUBLICATIONS

  29. Current Work • Theoretical Investigation: 3D Finite Element Modeling

  30. Current Work Strain Hardening Loading Fy max  10 y STRESS Un-Loading y STRAIN residual  8.5y

  31. Current Work • Effects of Cold Bending on Steel mainly fracture characteristics: • Perform Visual • Inspection using • NDT Techniques

  32. AASHTO Requirements

  33. ASSESSMENTS

  34. Acknowledgments • Samuel & Julia Flom Fellowship: USF • Dr. Rajan Sen • Ronald Medlock, Texas DOT “Performance and Effect of Hole Punching and Cold Bending on Steel Bridges”. Research project conducted by University of Texas at Austin and Texas A&M University, 2003. • TRB/AASHTO/NSBA

More Related