1 / 22

UNIVERSITYCOLLEGE LONDON DEPARTMENT OF CIVIL & ENVIRONMENTAL ENGINEERING In association with

Limit Load Analysis of suction anchors for cohesive materials By Dr Amir Rahim The CRISP Consortium Ltd/South Bank University 14 th CRISP User Group Meeting Friday 21 ST September 2001. UNIVERSITYCOLLEGE LONDON DEPARTMENT OF CIVIL & ENVIRONMENTAL ENGINEERING In association with. D. a. .

lucas
Download Presentation

UNIVERSITYCOLLEGE LONDON DEPARTMENT OF CIVIL & ENVIRONMENTAL ENGINEERING In association with

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Limit Load Analysis of suction anchors for cohesive materialsBy Dr Amir RahimThe CRISP Consortium Ltd/South Bank University14th CRISP User Group MeetingFriday 21ST September 2001 UNIVERSITYCOLLEGE LONDON DEPARTMENT OF CIVIL & ENVIRONMENTAL ENGINEERING In association with

  2. D a  L Introduction Suction anchors (or suction piles) are deep water anchors for floating structures or offshore oil installations. The pile consists of a hallow cylinder which has a top cap and a relatively thin wall.

  3. Problem Specifications • Pile diameter, D= 6m • Pile penetration, L=13.5m • Attachment point positions are: a= 6.75 m (or 1/2 depth L) a= 9 m (or 2/3 of depth L) a= 7.785 m (just below mid point, considered to be optimum position) • Angle of inclination  is 0o (horizontal), 15o, 26o, 30o, 45o, 90o (vertical)

  4. Problem Specifications • Load applied consists of 50 unequal load increments with maximum load=10000kN • The undrained shear strength, Cu, at mud-line is 3Kpa and it is assumed to increase with depth by a rate of 1.85. • Young's modulus at mud-line is assumed to be 300 KPa and it isassumed to increase with depth by a rate of 185. • The pile shell's thickness is 3cm. The pile is also assumed to be very stiff, with E=2.1E8 • A von Mises undrained material is used for the soil, with Poisson's ratio=0.49

  5. Finite Element Mesh .This was done using Femap Basic edition. Due to symmetry, only half the model was considered due X-Y elevation showing full mesh

  6. Finite Element Mesh

  7. Finite Element Mesh

  8. Finite Element Mesh

  9. Finite Element Mesh

  10. Finite ElementResults The following charts show FE results for cases with different load attachment point and angle. A von Mises material is used for all of these cases

  11. Finite ElementResults

  12. Finite ElementResults

  13. Finite ElementResults

  14. Finite ElementResults

  15. Finite ElementResults

  16. Finite ElementResults

  17. Finite ElementResults

  18. rigid Fan zone Pile Analytical solution using upper bound theory

  19. Analytical solution using upper bound theory The depth of the pile is 13.5m, therefore the total force is Pu(total)=16225 KN For a pile depth of 13.5m and assuming full adhesion, ie sin =1, we get Pult=16225 KN If we include the base resistance which is We get Pult =17017 KN This agrees reasonably with the FE solution for the case of =0o at a point below mid-depth which is 16400KN

  20. Conclusions • The FE solution for a middle attachment point loaded horizontally can be compared with the upper bound solution of laterally loaded pile. For this analysis the FE solution of =0o at a point below mid-depth is about 4% lower than the upper bound solution. • A more complex upper bound solution is necessary for cases in which the load is applied at an angle, due to the rotation of the pile. • Pull out capacity tends to reduce when the angle of load attachment approaches a horizontal level. This indicates that the vertical resistance is the predominant component for such deep piles. • All the analyses above were carried out using reduced integration (ie 2x2x2 Gauss points). Use of full integration produced a slightly higher collapse load

  21. von Mises Mohr-Coulomb C T CTriaxial Compression TTriaxial Extension Description of von-mises and Mohr-Coloumb yield surfaces in the -plane Conclusions • Use of Mohr Coulomb is preferred over use of von Mises material. The Mohr-Coulomb yield surface in the -plane slightly smaller giving a lower collapse load.

  22. Hardware specs • This problem contains about 30,000 d.o.f (about 10,000 nodes) • The PC used is AMD Athelon, 1GHZ, with 512 MB Ram • Each analysis took about 4 hours per increment • In conclusion, the use of a fast computer with large memory is highly recommended as it would make a huge difference in computation time

More Related