1 / 119

THERMAL ANALYSIS OF LIQUID ROCKET ENGINES

THERMAL ANALYSIS OF LIQUID ROCKET ENGINES. Mohammad H. Naraghi Department of Mechanical Engineering Manhattan College Riverdale NY 10471. Introduction to Cooling Methods. Combustion gases are 4000 to more than 6000 o F

lathrop
Download Presentation

THERMAL ANALYSIS OF LIQUID ROCKET ENGINES

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. THERMAL ANALYSIS OF LIQUID ROCKET ENGINES Mohammad H. Naraghi Department of Mechanical Engineering Manhattan College Riverdale NY 10471

  2. Introduction to Cooling Methods • Combustion gases are 4000 to more than 6000oF • Heat transfer rates from hot-gases to the chamber wall are 0.5 to over 130 BTU/in2s • A cooling system is needed in order to maintain engine integrity

  3. Chamber and Nozzle Cooling Techniques • Regenerative cooling • Dump cooling • Film cooling • Transpiration cooling • Ablative cooling • Radiation cooling

  4. Regeneratively Cooled Rocket Engines

  5. Types of Cooling Channel Rectangular cooling channels

  6. Cooling Channels

  7. High Aspect Ratio Cooling Channels

  8. A rocket chamber nozzle made of a copper alloy with machined cooling channels (no closeout)

  9. Tubular Cooling Channel Chamber jacket The number of coolant tubes required is a function of the chamber geometry, the coolant weight flow rate per unit tube, the maximum allowable tube wall stress, and fabrication consideration

  10. Tubular Cooling Channel Chamber jacket Tubular cooling channel configuration at throat area(parts of nozzle with small diameter)

  11. Cooling Channel Concepts

  12. Copper NARloy-Z SS-347 Glidcop Inconel718 Amzirc Columbium SS-347 Nickel Copper Monel Wall Materials Coating: Close-out: Wall: • Platinum • Nicraly • Soot • Zirconia

  13. Propellants • H2-O2 • RP1 (JET-A) C12H23-O2 • Methane-LOX CH4-O2 • Hydrogen Peroxide

  14. Coolants • Liquid Hydrogen • Liquid Oxygen • Water • RP1 (JET-A) • Methane • Hydrogen Peroxide

  15. Issues in Designing Cooling Passages • Keeping nozzle and wall temperatures below material limits • Keep pressure drop reasonable • Overcooling is detrimental to engine performance • Coolant exit condition be suitable for injector or running a turbo pump

  16. Modes of Heat Transfer Coolant convection Conduction within the wall Convection and radiation from combustion gases (hot-gases). All these modes of heat transfer must be conjugated

  17. Hot-gas 2 1 n 3 Modeling Heat Transfer in Regeneratively Cooled EngineTypical Nozzle Broken into a Number of Stations Coolant in

  18. Typical Cross-Section of Nozzle Due to symmetry calculation can be performed for a half cooling channel.

  19. Convection from Hot-Gases • The first step is to determine hot-gas thermodynamics and transport properties • CEA (Chemical Equilibrium with Applications) code can be used to evaluate the hot-gas properties. This program is a public domain code and can be downloaded from NASA Glenn’s site:http://www.grc.nasa.gov/WWW/CEAWeb/ • Typical results of CEA with rocket option for the SSME

  20. Hot-Gas Side Convective Heat Flux Or n is the station number TGAW and iGAW are adiabatic wall temperature and enthalpy TGW and iGW are gas-side wall temperature and enthalpy hG is the gas-side heat transfer coefficient is constant pressure hot-gas specific heat at reference condition

  21. Adiabatic Wall Temperature (Enthalpy) The reference enthalpy of the gas side, is given by (Eckert): The adiabatic wall enthalpy (Bartz and Eckert) Subscripts S and 0 represent static and stagnation conditions

  22. Hot-Gas Side Convective Heat Transfer Coefficient Dittus-Bolter correlation

  23. Hot-Gas Side Convective Heat Transfer Coefficient Bartz correlation  Is correction factor for property variation across the boundary layer

  24. Computational Methods for Hot-Gas Heat Flux Calculations • Boundary Layer analysis using available codes, such as TDK (Two Dimensional Kinetics) • TDK has two boundary layer modules (BLM, Boundary Layer Module, and MABL, Mass Addition Boundary Layer) • MABL can be used for transpiration cooling • Computation time for TDK is approximately two minutes • CFD codes

  25. CFD Results, Static Temperature for the Regen Part of the SSME

  26. Comparison Between Heat Fluxes Based on Various Methods for the SSME

  27. Wall Conduction Models • Two approaches can be used for wall • conduction: • Simple one-dimensional heat conduction • Two or Three-dimensional finite-difference or finite-element methods

  28. One-dimensional wall conduction TCAW 1/hFhCAC t/kA 1/hGA TGAW

  29. TCAW 1/hFhCAC t/kA 1/hGA TGAW One-dimensional wall conduction Fin efficiency l 2

  30. Soot Layer Thermal Resistance For engines with hydrocarbon fuel with Pc< 1500 psi From Modern Engineering for Design of Liquid-Propellant Rocket Engines, D. K. Huzel and D. H. Huang Progress in Astronautics and Aeronautics, Vol. 147, 1992

  31. Soot Layer thickness For the converging section: tsoot = 0.0041213(A/At) + 0.0041023 1<A/At<2 tsoot = 0.01234 2<A/At For the diverging section: tsoot = -0.0000442(A/At)2 + 0.0011448(A/At) + 0.0070920 1<A/At<12 tsoot=0.01445 12<A/At tsootare in inches

  32. Finite Difference Approach

  33. 3-D Finite Difference Method

  34. i,j+1,n i,j,n-1 i-1,j,n i,j,n i+1,j,n i,j,n+1 i,j-1,n 3-D Finite Difference Method Energy balance for a typical middle node

  35. 3-D Finite Difference Method i,j+1,n i,j,n-1 Energy balance for a typical surface node i-1,j,n i,j,n i+1,j,n Qr i,j,n+1 Qc

  36. Sample Results of Wall Temperature Distribution for the SSME

  37. Sample Results of Wall Temperature Distribution for the SSME Throat

  38. Sample Results of Wall Temperature Distribution for an Engine with Pass-and-half Tubular Cooling Channels

  39. Sample Results of Wall Temperature Distribution for an Engine with Pass-and-half Tubular Cooling Channels

  40. Coolant Flow Convection Two approaches can be used for coolant flow analysis: • One dimensional flow and heat transfer • Multidimensional CFD analysis

  41. Coolant Flow Convection • One-dimensional channel flow with variable cross-section for calculation pressure drop. • Heat transfer to coolant is evaluated based on the heat transfer coefficients calculated using Nu=f(Re,Pr) correlations. • GASP (Gas Properties) and WASP (Water and Steam Properties) are used for evaluating coolant properties (these programs are public domain codes).

  42. Variables Effecting Coolant Convection • Surface roughness • Entrance effect • Curvature effect • Using swilers • Cooling channel contraction and expansion • Pressure drop • Cooling channel tolerance and blocked channel

  43. Cooling Channel Heat Transfer Coefficient for Liquid Hydrogen Where

  44. Cooling Channel Heat Transfer Coefficient for RP-1 Shell correlation Rocketdyne correlation

  45. Cooling Channel Heat Transfer Coefficient for RP-1

  46. Cooling Channel Heat Transfer Coefficient for Methane

  47. Heat Transfer Coefficient for Oxygen psia Where

  48. Heat Transfer Coefficient for Fuels as Coolants

  49. Coking Characteristics of RP1 Range of Conditions Tested During RP1 Cooling Claflin, S.E., and Volkmann, J.C., “Material; Compatibility and Fuel Cooling Limit Investigation for Advanced LOX/Hydrocarbon Thrust Chambers,” AIAA 90-2185, AIAA/SAE/ASME/ASEE 26th Joint Propulsion Conference, Orlando, FL, 1990.

  50. Entrance Effect

More Related