1 / 28

Caterpillar Cat 345C EXCAVATOR (Prefix MDC) Service Repair Manual (MDC00001 and up)

service repair manual

kmyu72werm8n
Download Presentation

Caterpillar Cat 345C EXCAVATOR (Prefix MDC) Service Repair Manual (MDC00001 and up)

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Service Repair Manual Models 345C EXCAVATOR

  2. ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE)(SEBP5600 - 00) -... 1/2 Shutdown SIS Previous Screen Product: EXCAVATOR Model: 345C EXCAVATOR MDC Configuration: ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE) Disassembly and Assembly C11 and C13 Engines for Caterpillar Built Machines Media Number -RENR9214-23 Publication Date -01/05/2015 Date Updated -22/05/2018 i02247172 Fuel Transfer Pump - Remove SMCS - 1256-011 Removal Procedure NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products. Dispose of all fluids according to local regulations and mandates. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2020/7/21

  3. ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE)(SEBP5600 - 00) -... 2/2 Illustration 1 g01131526 1. Disconnect hose assembly (1). 2. Disconnect tube assemblies (2). 3. Remove bolts (3). 4. Remove fuel transfer pump (4). Copyright 1993 - 2020 Caterpillar Inc. Tue Jul 21 07:20:53 UTC+0800 2020 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2020/7/21

  4. ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE)(SEBP5600 - 00) -... 1/2 Shutdown SIS Previous Screen Product: EXCAVATOR Model: 345C EXCAVATOR MDC Configuration: ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE) Disassembly and Assembly C11 and C13 Engines for Caterpillar Built Machines Media Number -RENR9214-23 Publication Date -01/05/2015 Date Updated -22/05/2018 i02247178 Fuel Transfer Pump - Install SMCS - 1256-012 Installation Procedure Illustration 1 g01131526 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2020/7/21

  5. ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE)(SEBP5600 - 00) -... 2/2 1. Position fuel transfer pump (4). 2. Install bolts (3). 3. Connect tube assemblies (2). 4. Connect hose assembly (1). Copyright 1993 - 2020 Caterpillar Inc. Tue Jul 21 07:21:50 UTC+0800 2020 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2020/7/21

  6. ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE)(SEBP5600 - 00) -... 1/2 Shutdown SIS Previous Screen Product: EXCAVATOR Model: 345C EXCAVATOR MDC Configuration: ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE) Disassembly and Assembly C11 and C13 Engines for Caterpillar Built Machines Media Number -RENR9214-23 Publication Date -01/05/2015 Date Updated -22/05/2018 i02258461 Electronic Unit Injector - Remove SMCS - 1290-011 Removal Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 5F-4764 Pry Bar 1 Start By: a. Remove the rocker shafts. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod - Remove". https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2020/7/21

  7. ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE)(SEBP5600 - 00) -... 2/2 Illustration 1 g01135732 1. Disconnect harness assembly (1) from electronic unit injector (2). 2. Remove bolt (3). 3. Position Tooling (A) under unit injector clamp (4) in order to remove electronic unit injector (2). Copyright 1993 - 2020 Caterpillar Inc. Tue Jul 21 07:22:47 UTC+0800 2020 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2020/7/21

  8. ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE)(SEBP5600 - 00) -... 1/4 Shutdown SIS Previous Screen Product: EXCAVATOR Model: 345C EXCAVATOR MDC Configuration: ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE) Disassembly and Assembly C11 and C13 Engines for Caterpillar Built Machines Media Number -RENR9214-23 Publication Date -01/05/2015 Date Updated -22/05/2018 i03781931 Electronic Unit Injector - Install SMCS - 1290-012 Installation Procedure Table 1 Required Tools Tool Part Number Part Description Qty 9U-6862 Tapered Brush 1 B 9U-7237 Brush Extension 1 9U-6863 Small Bore Brush 1 C 9U-7237 Brush Extension 1 D 8T-2998 Lubricant 1 1U-5718 Vacuum Pump 1 E 169-7372 Fluid Sampling Bottle 1 4C-4057 Tube 1 NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2020/7/21

  9. ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE)(SEBP5600 - 00) -... 2/4 1. Evacuate as much fuel and oil as possible from the cylinder head before installing the injector. Several evacuations may be necessary. Use Tooling (E) to remove the fuel and oil from the cylinder head. Illustration 1 g01135874 2. Use Tooling (B) to clean injector seating (5) . 3. Use Tooling (C) to clean tip bore (6) . Note: Do not reuse seals. Use new seals for installation. 4. Lubricate the bore lightly with a 50/50 mix of clean engine oil and Tooling (D) . https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2020/7/21

  10. ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE)(SEBP5600 - 00) -... 3/4 Illustration 2 g01135732 Illustration 3 g01135876 5. When you install a new injector the E-Trim value must be programmed into the engine control module. The injector confirmation code may need to be programmed into the engine control module. E-Trim Value (X) is a twelve digit alphanumeric code that is supplied with the data sheet that comes with the new injectors. Injector Confirmation Code (Y) is a four digit numeric code. Both of the codes are located on the top of electronic unit injector (2) . Use the following menu to program the E-Trim value. ◦ ECM Summary Screen ◦ Service Menu ◦ Calibration https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2020/7/21

  11. ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE)(SEBP5600 - 00) -... 4/4 ◦ Injector Code Calibration NOTICE When an electronic unit injector is replaced, the new electronic injector code must be programmed into the engine's personality module software by using the calibration menu on the Electronic Service Tool. If the new electronic injector code is not entered, the characteristics of the previous electronic unit injector is assumed. If it is not possible to immediately reprogram the electronic injector code into the personality module software, the engine will not be severely harmed. The new electronic injector code should be reprogrammed as quickly as possible in order to optimize engine performance. 6. Install electronic unit injector (2) and unit injector clamp (4) . Note: Use new bolt (3) . 7. Install bolt (3) . 8. Connect harness assembly (1) to electronic unit injector (2) . Tighten harness assembly (1) to a torque of 2.50 ± 0.25 N·m (22 ± 2 lb in). End By: Install the rocker shafts. Refer to Disassembly and Assembly, "Rocker Shaft and Pushrod - Install". Copyright 1993 - 2020 Caterpillar Inc. Tue Jul 21 07:23:43 UTC+0800 2020 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2020/7/21

  12. ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE)(SEBP5600 - 00) -... 1/4 Shutdown SIS Previous Screen Product: EXCAVATOR Model: 345C EXCAVATOR MDC Configuration: ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE) Disassembly and Assembly C11 and C13 Engines for Caterpillar Built Machines Media Number -RENR9214-23 Publication Date -01/05/2015 Date Updated -22/05/2018 i02370015 Electronic Unit Injector Sleeve - Remove SMCS - 1713-011 Removal Procedure Type 1 Table 1 Required Tools Tool Part Number Part Description Qty A 9U-6891 Injector Tool Group 1 NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products. Dispose of all fluids according to local regulations and mandates. NOTICE https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2020/7/21

  13. ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE)(SEBP5600 - 00) -... 2/4 Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. 1. Remove the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit Injector - Remove". 2. Drain the coolant from the cooling system into a suitable container for storage or for disposal. Refer to Operation and Maintenance Manual, "Capacities (Refill)" for the capacity of the cooling system. Refer to the Operation and Maintenance Manual, "Cooling System Coolant (DEAC) - Change" or Operation and Maintenance Manual, "Cooling System Extended Life Coolant - Change". Illustration 1 g01016237 3. Install Tooling (A) into electronic unit injector sleeve (1) . 4. Tighten the nut until electronic unit injector sleeve (1) is pulled free of the cylinder head assembly. Type 2 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2020/7/21

  14. ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE)(SEBP5600 - 00) -... 3/4 Table 2 Required Tools Tool Part Number Part Description Qty 221-9778 Puller Stud 1 128-7889 Bridge Puller 1 A (1) 9U-6877 Thrust Bearing 1 5P-8247 Hard Washer 1 4K-0367 Nut 1 ( 1 ) The tools that are listed in the chart are part of the 9U-6891 Injector Tool Group . 1. Remove the electronic unit injector. Refer to Disassembly and Assembly , "Electronic Unit Injector - Remove". 2. Drain the coolant from the cooling system into a suitable container for storage or for disposal. Refer to Operation and Maintenance Manual, "Capacities (Refill)" for the capacity of the cooling system. Refer to the Operation and Maintenance Manual, "Cooling System Coolant (DEAC) - Change" or Operation and Maintenance Manual, "Cooling System Extended Life Coolant - Change". https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2020/7/21

  15. ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE)(SEBP5600 - 00) -... 4/4 Illustration 2 g01016237 3. Install the puller stud from Tooling (A) into unit injector sleeve (1) . 4. Install the following parts from Tooling (A) over the stud: bridge puller, thrust bearing, hard washer and nut. 5. Tighten the nut until unit injector sleeve (1) is pulled free of the cylinder head assembly. Copyright 1993 - 2020 Caterpillar Inc. Tue Jul 21 07:24:40 UTC+0800 2020 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2020/7/21

  16. ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE)(SEBP5600 - 00) -... 1/5 Shutdown SIS Previous Screen Product: EXCAVATOR Model: 345C EXCAVATOR MDC Configuration: ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE) Disassembly and Assembly C11 and C13 Engines for Caterpillar Built Machines Media Number -RENR9214-23 Publication Date -01/05/2015 Date Updated -22/05/2018 i02370001 Electronic Unit Injector Sleeve - Install SMCS - 1713-012 Installation Procedure Type 1 Table 1 Required Tools Tool Part Number Part Description Qty B 4C-5552 Large Bore Brush 1 9U-7237 Brush Extension 1 C 9U-7244 End Brush 1 D 9U-7258 Driver Cap 1 E 4C-9507 Retaining Compound 1 NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2020/7/21

  17. ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE)(SEBP5600 - 00) -... 2/5 Dispose of all fluids according to local regulations and mandates. NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. Illustration 1 g01131579 1. Use Tooling (B) to clean the electronic unit injector bore. 2. Use Tooling (C) to clean the electronic unit injector seat. 3. Apply Tooling (E) to upper land (2) and lower land (3) on the electronic unit injector sleeve. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2020/7/21

  18. ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE)(SEBP5600 - 00) -... 3/5 Illustration 2 g01016237 4. Position electronic unit injector sleeve (1) in the cylinder head assembly. Use Tooling (D) and a hammer to seat the sleeve. 5. Install the electronic unit injectors. Refer to Disassembly and Assembly , "Electronic Unit Injector - Install". 6. Fill the cooling system with coolant. Refer to Operation and Maintenance Manual, "Capacities (Refill)" for the cooling system capacity. Refer to Operation and Maintenance Manual, "Cooling System Coolant (DEAC) - Change" or Operation and Maintenance Manual, "Cooling System Extended Life Coolant - Change" for the proper filling procedure. Type 2 Table 2 Required Tools Tool Part Number Part Description Qty B 9U-6862 Tapered Brush 1 9U-6863 Small Bore Brush 1 9U-7244 End Brush 1 9U-7237 Brush Extension 1 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2020/7/21

  19. ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE)(SEBP5600 - 00) -... 4/5 4C-5552 Large Bore Brush 1 C (1) 221-9778 Puller Stud 1 D (1) 9U-7258 Driver Cap 1 E 4C-9507 Retaining Compound - ( 1 ) Part of the 9U-6891 Injector Tool Group 1. Use Tooling (B) to clean the bore in the cylinder head for the electronic unit injector sleeve. NOTICE Ensure that the electronic unit injector sleeve and the cylinder head bore are completely free of oil, dirt, and sealant debris. Illustration 3 g01120522 2. Install new O-ring seals (2) on electronic unit injector sleeve (1) . Note: Do not apply Tooling (E) to the cylinder head surfaces. Apply Tooling (E) on the electronic unit injector sleeve only. 3. Apply Tooling (E) to the contact surface of electronic unit injector sleeve (1) on the surface that is marked "X". 4. Lubricate O-ring seals (2) with clean engine oil. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2020/7/21

  20. ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE)(SEBP5600 - 00) -... 5/5 Illustration 4 g01076119 5. Install Tooling (C) into the threads of electronic unit injector sleeve (1) . 6. Position Tooling (C) and the electronic unit injector sleeve in the cylinder head. Use care not to damage the O-ring seal on the electronic unit injector sleeve. 7. Use Tooling (D) and a hammer to install electronic unit injector sleeve (1) in the cylinder head. NOTICE Ensure that the electronic unit injector sleeve is properly seated in the cylinder head. The Tooling will "RING" when the electronic unit injector sleeve is fully seated in the bore of the cylinder head. 8. Remove Tooling (D) and Tooling (C) . Use a clean towel and remove excess Tooling (E) . 9. Install the electronic unit injector. Refer to Disassembly and Assembly , "Electronic Unit Injector - Install". 10. Fill the cooling system with coolant. Refer to Operation and Maintenance Manual, "Capacities (Refill)" for the cooling system capacity. Refer to Operation and Maintenance Manual, "Cooling System Coolant (DEAC) - Change" or Operation and Maintenance Manual, "Cooling System Extended Life Coolant - Change" for the proper filling procedure. Copyright 1993 - 2020 Caterpillar Inc. Tue Jul 21 07:25:37 UTC+0800 2020 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2020/7/21

  21. ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE)(SEBP5600 - 00) -... 1/2 Shutdown SIS Previous Screen Product: EXCAVATOR Model: 345C EXCAVATOR MDC Configuration: ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE) Disassembly and Assembly C11 and C13 Engines for Caterpillar Built Machines Media Number -RENR9214-23 Publication Date -01/05/2015 Date Updated -22/05/2018 i02247321 Turbocharger - Remove SMCS - 1052-011 Removal Procedure NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat products. Dispose of all fluids according to local regulations and mandates. 1. Drain the coolant system. Refer to Operation and Maintenance Manual, "Refill Capacities and Recommendations". https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2020/7/21

  22. ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE)(SEBP5600 - 00) -... 2/2 Illustration 1 g01131603 2. Disconnect hose assemblies (3), (4), and (6). 3. Disconnect tube assembly (5). 1. Remove nuts (1). 2. Remove turbocharger (2) and the gasket. Copyright 1993 - 2020 Caterpillar Inc. Tue Jul 21 07:26:34 UTC+0800 2020 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2020/7/21

  23. ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE)(SEBP5600 - 00) -... 1/2 Shutdown SIS Previous Screen Product: EXCAVATOR Model: 345C EXCAVATOR MDC Configuration: ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE) Disassembly and Assembly C11 and C13 Engines for Caterpillar Built Machines Media Number -RENR9214-23 Publication Date -01/05/2015 Date Updated -22/05/2018 i04001168 Turbocharger - Install SMCS - 1052-012 Installation Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 5P-3931 Anti-Seize Compound - NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2020/7/21

  24. ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE)(SEBP5600 - 00) -... 2/2 Illustration 1 g01131603 1. Apply Tooling (A) to the turbocharger mounting studs on the exhaust manifold. 2. Position the gasket and turbocharger (2) on the engine. Note: Discard the nuts after use. Use new nuts for installation. 3. Install nuts (1). 4. Connect tube assembly (5). 5. Connect hose assemblies (3), (4), and (6). 6. Fill the coolant system. Refer to Operation and Maintenance Manual, "Refill Capacities and Recommendations". Copyright 1993 - 2020 Caterpillar Inc. Tue Jul 21 07:27:30 UTC+0800 2020 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2020/7/21

  25. Thank you very much for your reading. Please Click Here. Then Get COMPLETE MANUAL. NO WAITING NOTE: If there is no response to click on the link above, please download the PDF document first and then click on it.

  26. ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE)(SEBP5600 - 00) -... 1/5 Shutdown SIS Previous Screen Product: EXCAVATOR Model: 345C EXCAVATOR MDC Configuration: ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE) Disassembly and Assembly C11 and C13 Engines for Caterpillar Built Machines Media Number -RENR9214-23 Publication Date -01/05/2015 Date Updated -22/05/2018 i07024212 Exhaust Manifold - Remove and Install SMCS - 1059-010 Removal Procedure NOTICE Keep all parts clean from contaminants. Contaminants may cause rapid wear and shortened component life. NOTICE Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids. Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products. Dispose of all fluids according to local regulations and mandates. Start By: https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2020/7/21

  27. ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE)(SEBP5600 - 00) -... 2/5 a. Remove the high-pressure turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Remove". b. Remove the precooler. Refer to Disassembly and Assembly, "Precooler - Remove". c. Remove the low-pressure turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Remove". Illustration 1 g06199242 1. Remove the lower bracket for the precooler, the upper bracket for the precooler, and the middle bracket for the precooler. 2. Remove bracket (1). Illustration 2 g06199244 3. Remove locknuts (2) and the spacers. Remove exhaust manifold (3) and the gaskets. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2020/7/21

  28. ISJ HEX COMMONALITY CHART MDC00001-UP (MACHINE)(SEBP5600 - 00) -... 3/5 Illustration 3 g06199252 4. If necessary remove studs (4). Installation Procedure Table 1 Required Tools Tool Part Number Part Description Qty A - Loctite MR2000 - - Loctite C5-A - B Loctite 8008(1) - - (1)For use in EAME only Illustration 4 g06199252 1. Install studs (4). Tighten studs (4) to a torque of 35 ± 5 N·m (26 ±4 lb ft) https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2020/7/21

More Related