1 / 11

SWITCH -MODE POWER SUPPLIES AND SYSTEMS

SWITCH -MODE POWER SUPPLIES AND SYSTEMS. Lecture No 10 Switching transformer design rules. Power losses analysis in switching regulators. Silesian University of Technology Faculty of Automatic Control, Electronics and Computer Sciences Ryszard Siurek Ph.D., El. Eng.

irish
Download Presentation

SWITCH -MODE POWER SUPPLIES AND SYSTEMS

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. SWITCH-MODE POWER SUPPLIES AND SYSTEMS Lecture No 10 Switching transformer design rules. Power losses analysis in switching regulators Silesian University of Technology Faculty of Automatic Control, Electronics and Computer Sciences Ryszard Siurek Ph.D., El. Eng.

  2. Flyback converter transformer IT I0 D1 Ipmax IC UIN R0 C Zp ZS U0 B t IT BS T energy storing during cycle I DB H Minimum number of zP turns assuming t = tmax, DB = Bs, UIN = UINmax: Assuming required output power equal to P0 zpmin – is set for the chosen core Certain air-gap is necessary to achieve required output power

  3. Cycle II - transistor T is off ID ID D1 I0 IDmax IC T R0 C ZS t t’ B U0 BS Energy stored in the core is trans-fered to the output during cycle II H Selecting t’ < T-t for the maximum output power Po one decides to work with the discontinuous magnetic flux flow in the whole range of load changes. To increase t’ one must also increase LS, and it is related to higher number of turns of the secondary winding zS. When t’ = T-t transformer starts to operate with continuous magnetic flux flow. For discontinuous flux flow For continuous flux flow

  4. Flyback transformer design simplified procedure Select maximum (nominal) output power Po Select switching frequency – basing on specifications of available magnetic material, semiconductors etc. Calculate tmax, current Imax and required value of Lp Select core dimensions accordind to Hahn diagrams or using „AP” method (same as in inductor design procedure) Calculate (find from diagrams) the air-gap Calculate minimum number of primary turns, calculate required number of turns zP Select operating pronciple (continuous or discontinuous flux flow) Calculate secondary number of turns zS • Usually discontinuous flux flow is observed in flyback converters due to the following reasons : • lower number of winding turns (lower „copper” power losses) • lower level of EMC disturbances (transistor switches on with current equal to 0) • self-oscillating converter is very easy to design (low-cost solution)

  5. Forward converter transformer Ip Ip IS IM UIN Zp ZS US Lp transformer equivalent circuit Selection of the core - basing on diagrams (nomograms etc.) relating core dimensions to total power for certain converter topology Calculation of minimum number of turns for the primary winding to avoid saturation in most unfavourable operating conditions Equation identical for any converter topology Selection of wire cross section (diameter) taking into account primary current RMS value and calculation of number of turns for required winding inductance Lp (using Al constant for selected core) – the following condition must be performed: zp> zpmin

  6. Calculation of secondary winding (windings) number of turns Calculation of wire cross section area (copper strip, litz wire) for secondary winding resulting from secondary current RMS value ISrms=nIprms Checking if it is enough space to place windings in the core (bobbin) window area – required isolation and winding arrangement according to safety standards must be considered bobbin secondary windind magnetic core leakage distance (6 mm) Safety insulation (3 layers) primary winding functional insulation (between winding layers) 3 mm

  7. General notes Core power loses are higher when frequency and flux density amplitude increase - that is why the high value of primary inductance Lp is desirable High Lp value is related to more primary turns – more trouble with placing the winding in the bobbin and higher „copper” losses - look for optimum settlemet! Chose the magnetic core with best available performance – high saturation flux density Bs, lowest power losses, smallest dimensions Small air-gap in transformer core may be considered (forward converter) – better utilisation of the core may be achieved by lowering magnetic remanence B DB - without air-gap DB - with small air -gap H Remember that Bs value decreases with temperature – at 100oC it is lower by 20% – 25% in comparison to the value specified at 25oC

  8. Switching regulator power losses analysis 1. Switching power losses (dynamic) LL L UT IL ILmax IL I0 I0 IT ID T UIN D C Ro t T Ucontr t 0 ILmax IT ILmin ts QR - diode reverse charge [mC] ILmax tf td , ID t1 t1 ILmin overvoltage due to leakage inductance UT -IRmax UIN ITrmsrds Discharging of transistor capacitances CBCand CBE (bipolar transistors) Eloss

  9. Swith-mode power supply power losses - review Power losses in passive components - winding resitances (skin and proximity effects) - capacitor series resitance (ESR) – output filer electrolytic capacitors - magnetic core losses (hysteresis and eddy currents) - power losses in snubbar circuits Static power losses in semiconductors: - related to ON- resistance of MOSFET transistor or saturation voltage drop across bipolar transistor - related to voltage drop across rectifier diodes (mains input rectifier) and fast swiching output diodes IMPORTANT! for bipolar transistors and diodes for MOSFET trnasistors Switching (dynamic) power losses - related to semiconductor switching times, reverse charges - depandant on base (gate) drive circuits

  10. How to minimize power losses – general rules Power losses in passive components - select proper wire diameter, use copper stripes or litz wire - select low ESR capacitors (for switching applications), as big (dimensions) as possible, connected in parallel, - make wide and thick copper paths on the PCB - select modern ferrite cores with best performance at specified operating frequency and smallest dimensions - avoid high amplitude of flux density changes - recover the magnetising energy – do not dissipate it - use converter topologies with low overvoltages – decrease the influence of leakagae inductances (eg. two-transistor „forward” topology) Static power losses in semiconductors: - select MOSFET trnasistors with low on-resistance - in high power and high voltage applications use IGBT modules (simple MOSFET drive circuits, low saturation voltage drop as for bipolar transistors) - use Shottky diodes if possible (voltage drop below 0,5V) - use synchronous rectification technique After switching on the internal body diode the transistor with very low on-resistisance switches on – the voltage drop across the conducting transistor is much lower than across the diode

  11. Transistor dynamic power losses - select fast transistors (low tr anf tf times) - use special converter topologies with zero-current or zero-voltage switching (eg. resonant topologies) - design carefully snubbar circuits Voltage UT rise without snubbar circuit IT Zp UT CIN Charging of the capacitor delays voltage rise across the switching transistor decreasing significantly transistor power losses UIN Cs IT UT T t Ds It is possible to select such value of the capacitor Cs, that the overall power loss in the transistor and snubbar circuit reaches minimum.

More Related