1 / 63

Course : Applied Electronics

Course : Applied Electronics. Course Code:22329. Teaching Scheme. Examination Scheme Theory. Examination Scheme Practical. Unit -01 Low Power Amplifier -16 Marks. Course outcome. Use transistor as low power amplifier.

glenc
Download Presentation

Course : Applied Electronics

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Course: Applied Electronics Course Code:22329 Applied Electronics , Mrs.S.V.Naik, E & TC Dept

  2. Teaching Scheme Applied Electronics , Mrs.S.V.Naik, E & TC Dept

  3. Examination SchemeTheory Applied Electronics , Mrs.S.V.Naik, E & TC Dept

  4. Examination SchemePractical Applied Electronics , Mrs.S.V.Naik, E & TC Dept

  5. Unit -01 Low Power Amplifier -16 Marks Applied Electronics , Mrs.S.V.Naik, E & TC Dept

  6. Course outcome Use transistor as low power amplifier Applied Electronics , Mrs.S.V.Naik, E & TC Dept

  7. TRANSISTOR CONFIGURATIONS AND BIASING Applied Electronics , Mrs.S.V.Naik, E & TC Dept

  8. Transistor configurations • A general two port network is • This network has input port and output port. Therefore the total number of terminals are four. Ii 2 Io 1 Two port network Output port Input port 2 1 Applied Electronics , Mrs.S.V.Naik, E & TC Dept

  9. But transistor have only 3 terminals, hence we treat one of the three terminals “common” to input and output port. • Depending on which terminal is made common to input and output port, there are three possible configurations of transistor, they as follows: • Common base configuration • Common emitter configuration • Common collector configuration Applied Electronics , Mrs.S.V.Naik, E & TC Dept

  10. Common Base (CB) Configuration a) NPN transistor b) PNP transistor Applied Electronics , Mrs.S.V.Naik, E & TC Dept

  11. In CB configuration, base acts as common terminal between the input and output ports. • The input voltage VEB is applied between emitter and base while output voltage VCB is taken between collector and base. • Current relations: • The output current IC is given by IC = IC(INJ) + ICBO where IC(INJ) = injected collector current and ICBO = reverse saturation current of CB junction • As ICBO flows due to minority carriers, it is negligible as compared to IC(INJ), ∴ IC ≈ IC(INJ) • Current amplification factor (αdc): αdc = IC / IE Applied Electronics , Mrs.S.V.Naik, E & TC Dept

  12. Common Emitter (CE) Configuration Applied Electronics , Mrs.S.V.Naik, E & TC Dept

  13. In CE configuration, emitter acts as common terminal between input and output poets. • The input voltage VBB is applied between base and emitter while output voltage VCC is taken between collector and emitter. • Current relations: • For CB configuration, we can write IC = αdc IE + ICBO • Similarly for CE configuration, we can write IC = βdc IB + ICEO • Current gain (βdc): βdc = IC / IB Applied Electronics , Mrs.S.V.Naik, E & TC Dept

  14. Common Collector (CC) Configuration a) NPN transistor b) PNP transistor Applied Electronics , Mrs.S.V.Naik, E & TC Dept

  15. In CC configuration, collector acts as a common terminal between input and output. • The input voltage VEE or VBB is applied between base and collector while output voltage VCC taken between collector and emitter. • Current gain (γdc): γdc = IE / IB Applied Electronics , Mrs.S.V.Naik, E & TC Dept

  16. Comparison of configurations Applied Electronics , Mrs.S.V.Naik, E & TC Dept

  17. Amplification and Amplifier • Amplification: Amplification is a process of adding strength to the input signal or it is a process of “magnifying” the input signal without changing its shape. • Amplifier: • The circuit which amplifies a small input signal is called as an “amplifier”. • An amplifier is required to amplify weak signals and it is used in radio, TV, telephones, mobile phones, music system etc. Applied Electronics , Mrs.S.V.Naik, E & TC Dept

  18. Amplifier +Vdc RS IO Ii Amplifier (Voltage gain AV) RL VS Vi Vo Ri Ro Applied Electronics , Mrs.S.V.Naik, E & TC Dept

  19. In order to magnify the input signal VS all the amplifier need a source of energy which is provided by battery or DC supply. • The dc supply is also essential for biasing the BJT used in amplifier circuits. • The amplifier should contain atleast one active device such as transistor or FET or OPAMP. • If transistor is used then it should be in the active region. Applied Electronics , Mrs.S.V.Naik, E & TC Dept

  20. Amplifier characteristics • 1. voltage gain AV and current gain AI : The gain of an amplifier is defined as the ratio of output quantity to the input quantity. ∴ AV = Vo/ Vi And AI = Io/ Ii The gain of amplifier should be as large as possible. • Input resistance (Ri): It is the resistance seen looking into the input terminals of an amplifier. Ideally Ri should be infinite. Applied Electronics , Mrs.S.V.Naik, E & TC Dept

  21. Output resistance (Ro): It is the resistance seen looking into the output terminals of an amplifier when the input signal Vi = 0 and output circuit is open circuited. Ro should be equal to zero ideally. Applied Electronics , Mrs.S.V.Naik, E & TC Dept

  22. Classification of Amplifiers Applied Electronics , Mrs.S.V.Naik, E & TC Dept

  23. Single Stage Amplifier • Depending on which terminal of transistor is made common between input and output, the amplifiers are classified into three types as follows: • Common Emitter (CE) amplifier • Common Collector (CC) amplifier or emitter follower. • Common Base (CB) amplifier Applied Electronics , Mrs.S.V.Naik, E & TC Dept

  24. Single stage RC coupled CE Amplifier C1 C2 CE Applied Electronics , Mrs.S.V.Naik, E & TC Dept

  25. Fig. shows the a single stage RC coupled CE amplifier. • Circuit Components and their Functions: • Resistors: • Resistors R1, R2 and RE are used to bias the transistor in active region by using voltage divider bias circuit. • RC is collector resistor used to control collector current. 2. Input coupling capacitor C1: • The input coupling capacitor C1 is used to couple the ac input voltage VS to the base of the transistor. • As capacitor block dc, C1 couples only the ac component of the input signal. • This capacitor also ensures that the dc biasing conditions of transistor remain unchanged even after applications of the input signal. Applied Electronics , Mrs.S.V.Naik, E & TC Dept

  26. 3. Bypass capacitor CE: • As CE is connected in parallel with RE is called emitter bypass capacitor CE. • This capacitor offer a low reactance to the amplified ac signal, therefore RE gets bypassed through CE for only the ac signals. • This will increase the voltage gain of the amplifier. 4. Output coupling capacitor C2: • This capacitor couples the amplifier output to the load or to the next stage amplifier. • It is used for blocking the dc part and passing only the ac part of the amplified signal to the load. Applied Electronics , Mrs.S.V.Naik, E & TC Dept

  27. Operation of the RC coupled amplifier: • In the absence of ac input signal current IB = IBQ, IC = ICQ and voltage VCE = VCEQ. The Q point is selected to be in the active region of transistor. • As ac input signal VS is applied, the base current varies above and below IBQ. • Hence output current IC varies above and below ICQ, because IC = βIB and this variation will be large. • As the IC varies, voltage across RC will also varies, because VRC = IC x RC. • Hence collector voltage VC varies above and below VCEQ as VC = VCC – ICRC. • Through C2 only the ac part is coupled to the load. Hence Vo is of same shape as VS but of large size. • Thus amplification has taken place. Applied Electronics , Mrs.S.V.Naik, E & TC Dept

  28. Applied Electronics , Mrs.S.V.Naik, E & TC Dept

  29. Frequency Response and Bandwidth • The frequency response is graph of amplifier output voltage (or gain) versus the frequency of input signal. • Ideally frequency response should be flat over the entire frequency range. • Practically the frequency response of an amplifier is not flat over the entire operating frequency region. Applied Electronics , Mrs.S.V.Naik, E & TC Dept

  30. The practical frequency response can be divided into three regions as follows: • Low frequency region. • Mid frequency region. • High frequency region. 1. Low frequency region: In low frequency region, the gain or output voltage decreases due to the increased reactance of the coupling and bypass capacitor. 2. Mid frequency region: In this region, gain and output voltage remain constant. 3. High frequency region: In this region, the output voltage and gain will decrease due to the transistor internal capacitances and stray capacitance. Applied Electronics , Mrs.S.V.Naik, E & TC Dept

  31. Bandwidth: • Bandwidth is the band of frequencies in which the magnitude of output voltage or gain is either equal or relatively close to their mid frequency band value. • The frequencies fL and fH are called cutoff frequencies or half power frequencies. • Bandwidth of the amplifier is defined as the difference between the half power frequencies. • Lower cutoff frequency (f1 or fL): It is the frequency of the input signal at which the amplifier gain or output voltage reduce to 70.7% of their mid frequency range value. f1 is always less than f2. • Upper cutoff frequency (f2 or fH): It is the frequency of the input signal at which the amplifier output voltage reduce to 70.7% of their mid frequency range value. f2 is always higher than f1. Applied Electronics , Mrs.S.V.Naik, E & TC Dept

  32. Frequency Response Applied Electronics , Mrs.S.V.Naik, E & TC Dept

  33. Applied Electronics , Mrs.S.V.Naik, E & TC Dept

  34. Multistage Transistor Amplifier • The multistage amplifier is obtained by cascading a number of amplifiers i.e. connecting a number of amplifier stages to each other with the output of the previous stage to the input of next stage. • The most important parameters of an amplifier are its input impedance, voltage gain, bandwidth and output resistance which are dependent on the particular applications. • In general, a single stage amplifier is not capable to fulfill all these requirements. Hence we have to use a multistage amplifier. Applied Electronics , Mrs.S.V.Naik, E & TC Dept

  35. Applied Electronics , Mrs.S.V.Naik, E & TC Dept

  36. Overall Gain of the Multistage Amplifier • Overall voltage gain: Let AV1, AV2, AV3….AVn be the voltage gain of n number stages of multistage amplifier. Then total voltage gain AV of multistage amplifier is given by AV = AV1 x AV2 x AV3 x ……. x Avn • Overall current gain: Similarly, overall current gain AI of multistage amplifier having n number of stages is given by AI = AI1 x AI2 x AI3 x …….. x AIn • Overall input resistance (Ri): the overall input resistance of a cascaded amplifier is equal to the input resistance of the first stage. Applied Electronics , Mrs.S.V.Naik, E & TC Dept

  37. Overall output resistance (Ro): The overall output resistance of a cascaded amplifier is equal to the output resistance of the last stage. • Gain in decibels: The gain expressed as a ratio of output voltage and input voltage is called as the linear gain. On the logarithmic scale the gain is expressed in decibels as follows: 1. Power gain in dB = 10 log10 [Po/ Pi] 2. Voltage gain in dB = 20 log10 [Vo/ Vi] Applied Electronics , Mrs.S.V.Naik, E & TC Dept

  38. Methods of Coupling Multistage Amplifier • In the multistage amplifier, the output signal of preceding stage is to be connected to the input of the next stage. This is called as interstage coupling. • To achieve interstage coupling, there are three coupling techniques: 1. R-C coupling 2. Transformer coupling 3. Direct coupling Applied Electronics , Mrs.S.V.Naik, E & TC Dept

  39. R-C coupled Amplifier Applied Electronics , Mrs.S.V.Naik, E & TC Dept

  40. Frequency Response Applied Electronics , Mrs.S.V.Naik, E & TC Dept

  41. Applications: • In public address (P.A.) amplifier system • Tape recorders • TV, VCR and CD players • Stereo amplifier • RC coupled amplifier are basically voltage amplifier. Applied Electronics , Mrs.S.V.Naik, E & TC Dept

  42. Transformer Coupled Amplifier Applied Electronics , Mrs.S.V.Naik, E & TC Dept

  43. Peaking due to resonance • Applications: • For impedance matching • For amplification of radio frequency (RF) signal. • In power amplifier • For transferring power to a low impedance load such as a loud speaker Applied Electronics , Mrs.S.V.Naik, E & TC Dept

  44. Direct Coupled Amplifier Applied Electronics , Mrs.S.V.Naik, E & TC Dept

  45. Applications: • In the operational amplifiers (OP-AMPS). • In the analog computations. • In the linear power supplies (voltage regulators). Applied Electronics , Mrs.S.V.Naik, E & TC Dept

  46. Field effect Transistor Applied Electronics , Mrs.S.V.Naik, E & TC Dept

  47. Construction Applied Electronics , Mrs.S.V.Naik, E & TC Dept

  48. Common Source FET amplifier Applied Electronics , Mrs.S.V.Naik, E & TC Dept

  49. Tuned Amplifier

More Related