1 / 16

Design of 10 pm storage ring

Design of 10 pm storage ring. Yichao Jing 11/11/2010. Outline. Introduction Linear lattice design and basic parameters Combined function magnets study and feasibility Nonlinear dynamics and dynamical aperture. Beam Dynamics Workshop. Yichao Jing. What is 10 pm?.

cameron-thomas
Download Presentation

Design of 10 pm storage ring

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Design of 10 pm storage ring Yichao Jing 11/11/2010

  2. Outline • Introduction • Linear lattice design and basic parameters • Combined function magnets study and feasibility • Nonlinear dynamics and dynamical aperture Beam Dynamics Workshop Yichao Jing

  3. What is 10 pm? • Natural emittance with or less than 10 picometerin both planes would greatly enhance the brightness simply due to the decrease in transverse beam size. • When beam has such a small emittance, it reaches the diffractive limit. for hard x-ray 1 Å, ɛx≈10-11m. Transversely coherent! Beam Dynamics Workshop Yichao Jing

  4. How to achieve 10 pm? Theoretically, the limit of emittance is given by We choose 5GeV beam, thus bending angle of each dipole must be very small. We use total 440 dipoles. with and minimized lattice is matched TME is achieved. Beam Dynamics Workshop Yichao Jing

  5. The lattice we use • We use so-called 11–BA type lattice which has 9 center dipoles and 2 edge dipoles. The dispersion is not closed within each cell while the outer 2 dipoles are adjusted that the dispersion within different cells is for insertion devices. • Theoretically, we use the non-acromat minimization for TME calculation. Dispersion and H function can be expressed as Beam Dynamics Workshop Yichao Jing

  6. Emittance minimization We obtain <H>dip by averaging H over all phase across the dipole and calculate extremum: Using small angle approximation The minimum of beta function and dispersion happen at the center of dipoles Beam Dynamics Workshop Yichao Jing

  7. Simulation– MAD result Using MAD for lattice calculation with constraint set as the values calculated above, find an optimal solution when <H>dip is minimized. Beam Dynamics Workshop Yichao Jing

  8. Effort in shortening the C • Using combined function magnets, we can minimize the number of magnets for optics matching. Instead of using quadrupole triplet, we use singlet while make the dipole with gradient. • After some data analysis to match the lattice, we find out Good matching but a factor of 4 is unclear! Beam Dynamics Workshop Yichao Jing

  9. Sort of “analytical” way • No matching process is carried out in the process and we manually change all the parameters(drift length– L; dipole gradient– Kc; matching quadrupoleKq) to search for best solution. • We choose one Kc and then vary L and Kq to get beta function and dispersion and tune. And then choose another Kc and do this again. Each Kc would have a set of band plot. Beam Dynamics Workshop Yichao Jing

  10. Phase stability diagram For a fixed Kc, by varying drift space length, we obtain necktie diagram. The boundary reaches stability limit. Almost cover phase region from 0 to Pi. Bigger beta function has greater effect in changing tune. Beam Dynamics Workshop Yichao Jing

  11. Dispersion and beta function Similarly, we have dispersion and beta function curves. The dashed lines indicate the theoretical result. No solution in this case, Kc=0.5 is too small. Beam Dynamics Workshop Yichao Jing

  12. First solution As we gradually increase the Kc value to about 1.0. First solution shows up with beta function matched to 0.15m and dispersion 3e-3m. Cell length is also nice compact– only 2.5m. Emittance is 6.8pm with 440 dipoles. Calculated B1/B = Kc*ρ≈ 78m-1, not possible for magnet fabrication. It is almost impossible to make a very large dipole with high gradient! Beam Dynamics Workshop Yichao Jing

  13. Chromaticity correction SF SD Two families of sextupoles are used First order Chromaticity corrected with sextupolestrengths: SF= -346 and SD= 222 unit is 1/m^3. Pole tip field about 0.57T when a 2cm bore radius magnet is used. Beam Dynamics Workshop Yichao Jing

  14. Dynamical aperture DA calculationwith 500 turns ELEGANT tracking gives a small aperture with 2.5mm in x and 1.5mm in y. No error or off momentum is included. Beam Dynamics Workshop Yichao Jing

  15. IBS effect on emittance • To study the IBS effect, we do simulation with ELEGANT. We use 2000 particles tracking of 1000 turns for a demo to see how the emittance depends on the peak current. Beam energy is @ 5GeV. IBS effect is small for this lattice. Beam Dynamics Workshop Yichao Jing

  16. To-do list and conclusion • More dynamical aperture optimization: higher order sextupoleeffect, tune dependence on actions, particle diffusion mechanisms in phase space, development of DA tracking codes, etc. • More careful calculation of IBS effect involving more particles and more tracking turns. • 10 picometer storage ring has the potential to become next generation light source. Beam Dynamics Workshop Yichao Jing

More Related