1 / 23

ORCNext – WP4 Development of supercritical technologies

ORCNext – WP4 Development of supercritical technologies. Catternan Tom. ORCNext – WP4 Development of supercritical technologies. Transcritical ORCs – Literature review. Transcritical ORCs. Better thermal matching  driving force LMTD↓  UA↑.

Download Presentation

ORCNext – WP4 Development of supercritical technologies

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. ORCNext– WP4Development of supercriticaltechnologies Catternan Tom

  2. ORCNext– WP4Development of supercriticaltechnologies Transcritical ORCs – Literature review

  3. Transcritical ORCs • Better thermal matching  driving force LMTD↓  UA↑ • Best efficiency and highest power output when temperature profile of HS and WF match  lower exergy destruction (Larjola et al.).

  4. Selection of working fluids • Wide range of applications and ranges  no consensus for best working fluid.

  5. Selection of working fluids

  6. Heat exchanger design Influence ORC parameters on HX design (Schuster and Karellas, 2012) • R134a, R227ea and R245fa • Jackson correlation (1979): Water and CO2 • HTC decreases with increasing supercritical pressure and temperature HX area increases • Relatively unknown heat transfer mechanisms around C.P.  need further investigation

  7. ORCNext– WP4Development of supercriticaltechnologies Forced convective heat transfer at supercritical pressures Literature review

  8. Supercritical state • Critical point ‘c’ • Supercritical state • For T>Tcrit Continuous transition from liquid-like fluid to gas-like fluid (no phase change)

  9. Thermophysical properties • (cp, m, r, l, Pr…)=f(T) • Pseudo-critical temperature Tpc= f(p)

  10. Thermophysical properties

  11. Literature overview • Experimental • H2O, CO2, nitrogen, hydrogen, helium, ethane, R22 • Uniform cross section • Circular • Recently: triangular and square • Uniform heat flux  electrically  forced Tw • Different experimental results • Numerical • Only recent

  12. General characteristicsHeat transfer enhancement Maximum HTC • ↓ • ↑ • Due to variation of thermophysical properties (1) Theory (∆) Experimental:= 140±4.4 kg/h; q = 1.44 W/cm² (2) Theory(x) Experimental:= 140±3.1 kg/h; q = 2.73 W/cm² (3) Theory (○) Experimental:= 280±5.6 kg/h; q = 3.32 W/cm² (4 Theory (●) Experimental:= 280±7.8 kg/h; q = 5.20 W/cm² Variation of the heat transfer coefficient with bulk temperature for forced convection in a heated pipe for carbon dioxide of 78.5bar flowing upwards in a 1.0 diameter vertical pipe.

  13. General characteristicsHeat transfer deterioration • Comparison upward and downward flow • Downward  no unusual behaviour • Upward  deterioration Upward flow Downward flow Wall and bulk temperature as a function of the distance along a vertical heated 1.6 cm diameter pipe for water at 245 bar (1.11 pcrit).

  14. General characteristicsHeat transfer deterioration • Comparison upward, downward and horizontal flow (1) Horizontal pipe – upper surface (2) Horizontal pipe – lower surface (3) Vertical pipe – upward flow (4) Bulk fluid temperature Temperature distribution as a function of local bulk enthalpy along heated vertical and horizontal pipes (1.6 cm diameter) for water at 245 bar (= 1.11 pcrit): and

  15. Influence of parameters • Heat flux Left: Ratio of the experimental heat transfer coefficient to the value calculated via the Dittus-Boelter equation;. Right: Wall temperature behaviour for low and high heat fluxes.

  16. Influence of parameters • Heat flux • Mass flow Generalized curves for water at 250bar (Lokshin et al.)

  17. Influence of parameters • Heat flux • Mass flow • Flow direction Comparison of heat transfer between an upward and downward flow for CO2 by Jackson and Evans-Lutterodt

  18. Influence of parameters • Heat flux • Mass flow • Flow direction • Pipe diameter Effect of tube diameter on heat transfer coefficient (Cheng X. et al.)

  19. Correlations • Bringer and Smith (1957) • Miropolsky and Shitsman (1959, 1963) • Petukhov, Krasnoshchekov and Protopopov (1959, 1961, 1979) • Domin (1963) • Bishop (1962, 1965) • Kutateladze and Leontiev (1964) • Swenson (1965) • Touba and McFadden (1966) • Kondrat’ev (1969) • Ornatsky et al. (1970) • Yamagata (1972) • Yaskin et al. (1977) • Jackson (1979) • Yeroshenko and Yaskin (1981) • Watts (1982) • Bogachev et al. (1983) • Griem (1995, 1999) • … Heat transfer coefficient for supercritical water according to different correlations (Cheng X. et al.)

  20. ORCNext– WP4Development of supercriticaltechnologies Goals and planning for the next 6 months

  21. Transcritical ORCs • Finish literature study (± 10 more papers to read) • Model sub – and transcritical cycle (together with WP1) • Choose parameter range • Compare both cycles using the Performance Indicators for several working fluids • Check influence of the variable parameters on the objective functions  sensitivity • Make a list of 3 working fluids, which will be used in the experimental setup

  22. Supercritical forced convection heat transfer • Investigate thermophysical properties under supercritical conditions of the selected working fluids (via REFPROP or EES) • Finish literature study • Deteriorated and improved heat transfer regimes • Onset deterioration • Correlations • Fundamental understanding heat transfer and occurring flow - Test setup have to be built: • Prepare setup • Choose materials • Order

  23. Thank you for your attention.

More Related