1 / 21

BEHAVIORAL JOB SAFETY ANALYSIS TRAINING

BEHAVIORAL JOB SAFETY ANALYSIS TRAINING. Elkhorn Construction Inc. What is a Behavioral Job Safety Analysis-BJSA. A BJSA is a tool in which we plan our work, identify hazards, mitigate the hazards, and assign the responsible people. It is basically the plan we will use to complete our work.

blithe
Download Presentation

BEHAVIORAL JOB SAFETY ANALYSIS TRAINING

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. BEHAVIORAL JOB SAFETY ANALYSIS TRAINING Elkhorn Construction Inc.

  2. What is a Behavioral Job Safety Analysis-BJSA A BJSA is a tool in which we plan our work, identify hazards, mitigate the hazards, and assign the responsible people. It is basically the plan we will use to complete our work.

  3. Elkhorn BJSA Front Page

  4. Elkhorn BJSA-Back Page

  5. What is the purpose of the BJSA? The purpose of the BJSA is to document how we will complete our work in a manner that identifies and protects us from any hazards we may face.

  6. Who should complete a BJSA? • The entire crew should discuss the BJSA and complete it as team. • A foreman may not notice something that a laborer sees as potentially hazardous. • The BJSA should be completed by a person that is familiar with the task to be done and hazards we may face. • It is usually done by a foreman or team lead.

  7. When should we complete a BJSA? • If we finish with a task and start a new task not covered on the original BJSA then we need a new one. • If conditions or hazards change then we need to updated and review the BJSA • A BJSA should be completed before we start any task. • If the task poses any hazards a BJSA is required. Normal office work would be an example of low risk task that would not need a BJSA

  8. Completing the BJSA Job Number, Elkhorn Office(Western Slope),Date Task Description-What are we going to do? What is the worst thing that may happen? Other permits associated with this BJSA Inspections required? Who are the TRAINED operators and spotters?

  9. Completing the BJSA-Hazard ID tool The Hazard ID tool helps us to recognize hazards present during our work Circle the PPE required for this job task-Does everyone know how to use the PPE Circle all hazards present. We will mitigate or reduce them later in the BJSA Sketch our work area in the box Identify the location where we will muster and show it on the sketch

  10. Completing the BJSA-the Job Safety Analysis Observable steps for the task Tools and Equipment used to complete the task Hazards we face while completing the task Steps to control or mitigate the hazards Who is responsible for the hazard control?

  11. Completing the BJSA-JobSteps • The job steps must be observable steps that we will do to complete the task. For example, Task: “Bolt 12 inch valve to metering skid”. Don’t make the steps too general, add enough detail so the steps are clear enough that those working on the task and others observing can understand what is to be done but they should not be a Standard Operating Procedure but a reminder of each general step of the task. • A task should have 4-12 job steps. Too few steps will be too vague and more than 12 steps probably indicates a separate task that requires a separate BJSA. If additional room is needed, use a blank BJSA. • Each step should note what is to be done, not how it is done. • Keep the job steps in the correct order.

  12. Completing the BJSA-Tools and Equipment • Any tools or equipment needed for the job step should be listed. Having them available make our job safer and more efficient. • Having them listed reminds us of hazards they may create.

  13. Completing the BJSA-Hazards • We need to identify any potential hazards we face at each job step. These can be large hazards like a crane dropping a load or a small hazard of bees being around. • We should list any hazards identified on the Hazard ID tool (front page) • The entire crew should list hazards. A group is more likely to think of all the hazards than a single person. • An example may be “sparks from grinding that can enter eyes or cause a fire”

  14. Completing the BJSA-Hazard Control • Once we have identified the hazards, we need to write how we will eliminate or control the hazard. • It is better to completely get rid of the hazard if possible. For example weld pipe on the ground instead of a heights to eliminate a fall hazard. • If we cant do that, we should try to control the hazard. If we can’t weld the pipe on the ground we may build a scaffold platform to reduce the fall hazard. • The last form of protection should PPE. If we can’t weld the pipe from scaffold then we would need to utilize a harness & lanyard attached to an anchor point

  15. Completing the BJSA-Hazard Control • Be specific in how we will control the hazard. Avoid phrases like “use PPE”. It should be something like “wear ear plugs and ear muffs while working in the compressor building”. • Keep the BJSA organized in a way that it is easy to see what we should be doing to protect ourselves. That can be listing the hazard on one line and listing the mitigation on the same line to the right. You may also number a hazard as #1 and label the mitigation with the same #1.

  16. Completing the BJSA-Hazard Control Responsibility • Once we have identified the hazard, talked about how we will deal with the hazard, then we will assign someone to be responsible for the hazard control. • This may be one person that will wear hearing protection while grinding or the entire crew working next to a compressor. • If a person is assigned, they need to make sure that they have taken care of the hazard before work starts.

  17. Signatures, Auditing, and SSE’s Print who completed the BJSA, the foreman that reviewed it prior to the start of work, and who audits the form. The crew should sign it once they review the BJSA. By signing it they agree that they understand it, agree to follow what it says, and they understand they must stop the work if we are not following our plan. They should also circle Y/N if they are a short service employee to let others know that they may need additional guidance.

  18. Utilizing the BJSA • The BJSA is a tool that will only protect us if we follow what it says. It takes everyone following the plan for it be effective. • The BJSA must be in place BEFORE we start the work. You are not permitted to go to work until it is completed correctly. • If conditions or our job steps change, we need to address those changes on the BJSA. • Remember if we finish one task before days end, we need to develop another BJSA to start a new task.

  19. BJSA Meet & Greet • If others are entering our work area, we need to greet them, ask them to review & sign our BJSA. • This could be other Elkhorn work groups, client personnel, or other contractors. • If you enter another groups work area ask to review their BJSA. You will be exposed to the same hazards they face, so you need to know how to protect yourself.

  20. BJSA Group Practice • As a group, complete a BJSA for changing a flat tire on a pickup truck. • Review the previous slides if needed to assist in the process.

  21. BEHAVIORAL JOB SAFETY ANALYSIS TRAININGElkhorn Construction Inc. Created by Justin Booth, OHST, CHST

More Related