1 / 12

Modeling the Input Optics using E2E

Modeling the Input Optics using E2E. S. Yoshida, R. Dodda, T. Findley, K.Rogillio, and N. Jamal, Southeastern Louisiana University – Acknowledgement – LIGO Livingston Observatory, SURF 2004, NSF B. Bhawal, M. Evans, V. Sannibale, and H. Yamamoto. Objectives.

alia
Download Presentation

Modeling the Input Optics using E2E

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Modeling the Input Optics using E2E S. Yoshida, R. Dodda, T. Findley, K.Rogillio, and N. Jamal, Southeastern Louisiana University – Acknowledgement – LIGO Livingston Observatory, SURF 2004, NSF B. Bhawal, M. Evans, V. Sannibale, and H. Yamamoto LIGO Laboratory

  2. Objectives A simulation model will be very convenient to study the impact of ground motion on the input optics, and on the input beam. Therefore, we seek to do the following: 1. Build an IO box using E2E. 2. Integrate it with the Simligo. 3. Run simulation with realistic ground motion. LIGO Laboratory

  3. The Process 1. Make an Small Optic Suspension (SOS) box, and validate it. 2. Use the SOS box to damp the motion of an optic when realistic ground motion is given. 3. Create a Mode Cleaner (MC) box, and try to lock the cavity when realistic ground motion is given to the Mode Cleaner optics. 4. Put all the optics ( MCs, SM, and MMTs ) in order, and create the Input Optic (IO) box. 5. Use the IO box in Simligo, and run the simulation for the entire detector. LIGO Laboratory

  4. Validating SOS – Role of the Table Top motion MC1 Yaw motion using two different schemes Schematic diagram of the SOS box with HAM motion as input LIGO Laboratory

  5. òò ACCX dt dt HAM table Vibration isolation stacks u v ¶ ¶ 1 1 - = - Table yaw = ( ) { ik u ( y , t ) ik v ( x , t )} 1 2 Accelerometer ¶ ¶ 2 y x 2 w ± w ± ( ) ( ) i t k y i t k x = = u ( y , t ) A e , v ( x , t ) A e 1 1 2 2 0 0 = = w q = w - k k k ( ) i k ( ){ u ( y , t ) v ( x , t )} 1 2 Calculating table’s Yaw X in Table u HAM stack box Table v Y in LIGO Laboratory

  6. Dependence of k on frequency LIGO Laboratory

  7. SM (0.75, 0.45) V MMT1 (0.1, 0.4) MC3 (0.75, -0.05) U (0, 0) q MMT3 (-0.8, 0.6) MC1 (0.75, -0.25) Calculating the suspension point motions of the optics u(x,y)= U - yq v(x,y)= V + xq U: table’s center of mass translational motion V: table’s center of mass translational motion q: table’s yaw motion LIGO Laboratory

  8. MC2 and MC3 LIGO Laboratory

  9. MC1 pendular motion with local damping LIGO Laboratory

  10. Mode Cleaner box – Preliminary Results LIGO Laboratory

  11. IO box with the full Detector box LIGO Laboratory

  12. Conclusions • HAM table motion estimated from the ACC[XY] DAQ signal • MC1, MC3 local damping optimized • MC box constructed and being tested • Combination of MC and IFO in progress LIGO Laboratory

More Related