1 / 24

ECE Projects Lab

ECE Projects Lab. Surface Mount Technology. What is SMT?. Surface Mount Technology Used primarily in industry Same circuitry with much smaller components Was not intended for individual soldering, but gaining popularity. SMT Components. “Reflow”.

ahmed-lott
Download Presentation

ECE Projects Lab

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. ECE Projects Lab Surface Mount Technology

  2. What is SMT? Surface Mount Technology Used primarily in industry Same circuitry with much smaller components Was not intended for individual soldering, but gaining popularity

  3. SMT Components

  4. “Reflow” a thermal process in which solder paste is used to electrically connect components to their attachment pads. It is the most common means to attach a surface mounted component to a circuit board “Reflow temperature” is the temperature at which the solder paste changes state from solid to liquid

  5. SMT Board

  6. Why SMT (advantages)? • Much smaller size • Components on both sides of board • Leads can be much shorter reducing inductance and resistance thereby increasing performance • Prototyping is more indicative of the final product

  7. How to SMT solder (techniques) • Fine tip soldering • Uses conventional soldering techniques on a much smaller scale • Hot plate reflow • Useful for single ICs with limited footprint • Oven reflow • Uses soldering paste and reflows entire board

  8. How to SMT rework • Solder wick • Uses fine mesh conductive Copper braid. Heat and capillary action pulls excess solder away • Hot air reflow • Uses hot air to reflow the solder with components present • De-Solder vacuum plunger/sucker • Uses small negative pressure to suck up excess solder

  9. Fine Tip SolderingConventional Equipment • Useful for Larger components • Causes eye strain • Requires a steady hand

  10. Fine Tip SolderingSpecialized Fine-tip tools • Hot-Air Rework Station AM6500 by JBC • Fine tip solder tools • Desoldering tools • Hot tweezers • Hot air gun

  11. Hot plate reflow • useful for smaller boards as heat distribution on a hotplate is far less uniform than a convection oven • end point is monitored visually

  12. Oven reflow • Typical Reflow oven • Large and bulky • Expensive $$$  • Cuisinart TOB 165 • Just as good • A small fraction of the cost

  13. Oven Reflow Overview • After applying solder paste and setting components, the board is inserted to be “cooked” • End result is a perfectly soldered board for a fraction of the cost (no eye strain either)

  14. Reflow Profile • The temperature of the reflow process must: • be precise enough to not damage IC’s through excess heat • be sufficient for reflow of solder

  15. Oven Reflow Steps Set IC’s and components Apply soldering paste Touch up (here using solder wick) Cook!

  16. Industrial SMT Movie • Silicon Run II

  17. Copper Solder Wick (rework) • useful for removing excess solder • braided copper mesh is used to remove solder via capillary action • Fine-tip or conventional soldering iron is used for heating braid and solder

  18. Hot air reflow (rework) • Hot-Air Rework Station AM6500 by JBC • Fine tip solder tools • Desoldering tools • Hot tweezers • Hot air gun

  19. How hot air reflow works • Hot air used to desolder IC • Vacuum extractor pulls IC after solder flows

  20. De-Solder vacuum plunger/sucker(rework) • Uses small vacuum to pull solder away from board • Hand-held manual version • Heated tip & vacuum combined on SMT rework station

  21. Summary • Fine tip soldering is hard, but essential sometimes • Hotplate or Oven reflow are great for creating a whole board at once • Rework techniques include Copper wick, Hot-air reflow, and de-solder vacuuming • ECE Projects Lab can do it all

  22. Credits/Work cited • http://en.wikipedia.org/wiki/Surface-mount_technology • General SMT info • http://www.heinc.com/jbc/repair.html • Hot air reflow station website • http://www.bidservice.com/Browses/NF_Detailed_Item_View_new.asp?ProductID=20069 • Place to purchase typical reflow oven • http://www.seattlerobotics.org/encoder/200006/oven_art.htm • Another group that has done a similar project with a toaster oven • http://www.circuitcellar.com/library/print/0704/Lacoste_168/ • Thermal profile for a toaster oven

  23. Design Lab Website • Presentations available • Online Reflow Tutorial • http://www.ee.duke.edu/DesignLab/

  24. Thanks!

More Related