1 / 31

Precision Dimensioning

Precision Dimensioning. Engineering II. Dimensioning Rectangular Prisms. Dimensioning Cylinders. The diameter of cylinders should be dimensioned in the rectangular view (not the circular view). Cylinders without a hole passing through them only require one view. Dimensioning Cones.

vmaldonado
Download Presentation

Precision Dimensioning

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Precision Dimensioning Engineering II

  2. Dimensioning Rectangular Prisms

  3. Dimensioning Cylinders • The diameter of cylinders should be dimensioned in the rectangular view (not the circular view). • Cylinders without a hole passing through them only require one view.

  4. Dimensioning Cones

  5. Dimensioning Spheres

  6. Rectangular Coordinate Dimensioning • Used when computer-controlled production machines are used to manufacture parts. • The designer should consult with personnel in manufacturing to ensure that the origin is located in an appropriate position. • Two types of rectangular coordinate dimensioning: • Coordinate Dimensioning with Dimension Lines • Coordinate Dimensioning Without Dimension Lines

  7. Coordinate Dimensioning with Dimension Lines

  8. Coordinate Dimensioning without Dimension Lines

  9. Tabular Dimensioning • Tabular dimensioning is used when a series of parts consists of the same features or geometry but vary in dimension. • Letters are used in place of dimension values, and the values are then placed in a table. • Most standard parts are dimensioned this way in catalogs, the machinery handbook, and in the back of most textbooks.

  10. Tabular Dimensioning

  11. Dual Dimensioning – Position Method • Millimeter value is placed above (or below) the inch value or separated by a dash.

  12. Dual Dimensioning – Bracket Method • Millimeter value is enclosed in square brackets. A note should be placed on the drawing such as: DIMENSIONS IN [ ] ARE MILLIMETERS.

  13. Tolerance Dimensioning • Why do we need tolerance dimensioning? • Interchangeable parts manufacturing • Parts are manufactured at widely separate localities • Effective size control • Modern industry relies on it for subcontracting and replacement parts • Accuracy is Expensive, however

  14. Reading Dimensions

  15. Specification of Tolerances Limit Dimension Bilateral-Equal Unilateral Bilateral-Unequal

  16. Tolerance • Tolerance is the total amount a specific dimension is permitted to vary (difference between the maximum and minimum limits). • The dimension below has a tolerance of .0003.

  17. Maximum Material Condition • When specifying tolerance dimensions, the maximum material condition (MMC) means the product or part contains the maximum amount of material specified by the tolerance. • The heaviest part.

  18. Maximum Material Condition • For the part shown here the MMC is 1.4996 since that size would yield the most material.

  19. Allowance • Allowance is the minimum clearance or maximum interference intended between the maximum material condition (MMC) of mating parts. • The allowance for the system below is: 25.000 - 24.890 = 0.110

  20. More Terminology • Nominal Size - General identification in fractions (ex. 1-1/2 for 1.500). • Basic Size - General identification in decimal (ex. 1.500). • Actual Size - Measured size. • Limits - Maximum and minimum sizes indicated by the tolerance dimensions.

  21. Clearance Fit • Space is always left between parts. • What is the allowance in this case? • 1.5000 – 1.4988 = .0012

  22. Interference Fit • Always an interference of material. • What is the allowance in this case? • 1.5000 – 1.5013 = -.0013 or just .0013

  23. Transition Fit • Fit might result in clearance or interference.

  24. Line Fit • Clearance or surface contact may result at assembly.

  25. Basic Hole System (Hole Basis) • The minimum size hole is taken as the basic size.  • Used when standard tools are used to produce holes (reamers & broaches).

  26. Basic Shaft System (Shaft Basis) • The maximum shaft size is taken as the basic size.  • When several parts having different fits, but one nominal size are required on a single shaft.

  27. Specifying a Fit - Inches • Determine type of fit and find corresponding table • Determine basic size • Find size range on table • Determine tolerances for Hole and Shaft • Remember values are in thousandths of an inch.

  28. Specifying a Fit - Inches • RC1 - Close Sliding Fit • Basic size of 1.500 • Upper tolerance on hole is +0.4, which is really +0.0004 • Lower tolerance on hole is -0. • Upper tolerance on shaft is -0.0004 • Lower tolerance on shaft is -0.0007

  29. Specifying a Fit - Inches

  30. Specifying Fits - Metric • Determine type of fit and find corresponding table • Determine basic size • Find size range on table • Determine tolerances for Hole and Shaft

  31. Specifying Fits - Metric • Loose Running Fit • Basic size of 25

More Related