1 / 34

Advances in Welding for Sanitary Designs

Advances in Welding for Sanitary Designs. Richard E. Avery Consultant to the Nickel Institute May 17, 2004. Possible Materials. 304L& 316L – used for vast majority of applications 6% Mo or super-austenitic SS Duplex stainless steels Ni-Cr-Mo nickel alloys

phillipk
Download Presentation

Advances in Welding for Sanitary Designs

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Advances in Welding forSanitary Designs Richard E. Avery Consultant to the Nickel Institute May 17, 2004

  2. Possible Materials • 304L& 316L – used for vast majority of applications • 6% Mo or super-austenitic SS • Duplex stainless steels • Ni-Cr-Mo nickel alloys • Commercially pure titanium

  3. Service Considerations • 304L vs 316L – Mo (2-3%) in 316L improves pitting & crevice cor. resist. • Both sensitive to stress cor. cracking over about 150oF • Duplex SS good resist. to SCC • Higher chlorides, low pH may require 6% Mo SS or Ni-Cr-Mo or titanium

  4. Welding Processes Used • GTAW or TIG- manual- orbital tube welding or automatic sheet • GMAW – MIG, pulsed arc mode • SMAW or covered electrode • Laser welding for manu. of welded tubing

  5. Typical Sanitary Piping Systems • Welded by gas tungsten arc welding (TIG) • Lines designed for CIP • Inside of tube welds often not accessible for grinding or inspection

  6. Manual vs Automatic Orbital Tube Welding • Short projects may favor manual welding • Manual welders better able to accommodate poorer fit-up conditions • Orbital welds have more consistent root weld beads and practically free from heat tint

  7. In response to 3-A Request • AWS D18.1Specification for Welding Austenitic Stainless Steel Tubing Systems in Sanitary (Hygienic) Applications • AWS D18.2Guide to Weld Discoloration Levels on Inside of Austenitic Stainless Steel Tube

  8. Goals of D18.1 & D18.2 • Guidance of judging root welds of tubes from OD appearance • Guides for Procedure & Performance Qualification, Preconstruction Weld Samples • Weld visual acceptance criteria • Illustration of weld discoloration levels

  9. AWS D18 Committee Work • Members – equipment producers, users & general interest groups • 36 weld samples, many with ID defects – examined on OD & ID by 3-A inspectors • Tube with varying levels of weld discoloration • Tube with varying discoloration levels

  10. Welding Qualifications • Welding Procedure Specification (WPS) - for each type of weld • Performance Qualification - to test welder’s ability • Preconstruction Weld Samples (PWS) - 3 welds made by each welder to aid in evaluating production welds

  11. Visual Examination Requirements • OD of welds examined by welder & inspector, to be consistent with WPS • Welds not meeting OD standards examined by borescope or other suitable means

  12. Visual Acceptance Criteria -ID & OD • Welds full penetration • No cracks, undercut, crevices, or embedded or protruding material • Offset not to exceed 10 %

  13. Visual Acceptance Criteriafor External, Non-ProductContact Surface These criteria give confidence that the inside weld surface is acceptable without an internal examination

  14. Non-product contact surface - Maximum concavity

  15. Non-product contact surface- Maximum convexity

  16. Visual Acceptance Criteria for Internal, Product Contact Surface • Max. concavity 0.012 in. • Max. convexity 0.012 in. • Oxide islands (slag spots), not greater that 1/16 in. in diameter & 4 per weld • No excessive heat-tint oxide

  17. AWS D18.2 (1999): Heat Tint Levels on the Inside of Welded 316L Austenitic Stainless Steel Tube The Sample Numbers refer to the amount of oxygen in the purging gas: No.1- 10ppm No.2 - 25ppm No.3 - 50ppm No.4 - 100ppm No.5 - 200ppm No.6 - 500ppm No. 7 - 1000ppm No.8 - 5000ppm No.9 -12500ppm No.10 -. 25000ppm Note: welds on type 304L SS showed no significant difference in heat tint colour from type 316L.

  18. Heat Tint - Acceptance Limits • Acceptable limits could vary with end application service, D18.1 or D18.2 • Typically 5 and greater is unacceptable • An acceptance level should be identified by number rather than ppm of oxygen or by workmanship standards for particular contract

  19. Factors Influencing Heat Tint • Oxygen in backing gas increases HT • Moisture in backing gas increases HT • Contaminants such as hydrocarbons increase discoloration • Hydrogen in backing gas decreases HT • Metal surface finish can affect appearance

  20. AWS D18.3 (Pending)Specification for Welding Tanks, Vessels, and Other Equipment in Sanitary (Hygienic) Applications • Welding Procedure & Performance Qual. • Visual Examination Acceptance Criteria:- reject defects; cracks, lack of penetration etc- acceptable & unacceptable weld profiles prior to weld finishing- annex – Weld & Adjacent Zone Finishes – WF-1 (as-welded) ~ WF-8 (ground flush & electropolished)

  21. 6% Mo or Superaustenitic SS • Typically: 21 Cr, 24 Ni, 6 Mo, 0.2 N • Areas for 6% Mo not handled by 316- high chlorides ~ over 1000 ppm- low pH environments- where better pitting, crevice and stress corrosion cracking resistance is required

  22. Welding 6% Mo SS • Use over-alloyed filler metal – minimum of 9% Mo Ni-Cr-Mo alloy • GTAW welding procedures similar to that for 304/316 except:- preferably avoid autogenous welds to avoid lower corrosion resistance - somewhat lower heat input and interpass temperature

  23. What are Duplex Stainless Steel? Low-carbon stainless steels containing approx. equal parts of ferrite and austenite from a balance of ferrite formers (Cr,Mo) with austenite formers (Ni,N) and heat treatment

  24. Duplex Stainless Steel Base Metal Upper Right, Weld Metal Bottom Left Source:The ESAB Group

  25. Duplex SS – alloy 2205 • Typically: 22 Cr, 5 Ni, 3 Mo, O.15 N • Structure is austenite islands in ferritic matrix ~ 50/50 is ideal • Higher strength – YS 2 to 3 times 316- forming requires greater power- more spring-back during forming

  26. Duplex SS – (cont.) • Stress corrosion cracking resistance substantially better than 304/316 • Pitting & crevice cor. Resistance equal or better than 316 in many media • Good resistance to erosion & abrasion

  27. DSS Welding - General Requirements • No preheat – 300F interpass typical • Heat input 15 to 65 kJ/in. • To avoid high ferrite in welds, filler metals with higher nickel used ~ 2209 with 9% nickel • Avoidance of arc strikes, oxidation, grinding out of craters

  28. GTAW Process - DSS • Used for root passes and orbital welds • Filler essential for ferrite-austenite balance • Ar + 20-40% He + up to 2.5% N2 to counter N loss from weld - no hydrogen • Backing gas to maintain weld N content

  29. Duplex SS - Welding • To avoid high ferrite in welds, filler metals with higher nickel used ~ 2209 with 9% Ni • Avoid loosing N in weld – N backing common • Heat input 15 to 65 kJ/in • Interpass temperature 300F typical

  30. Nickel Alloys & Titanium • Selectively used for their high corrosion resistant properties • Ni-Cr-Mo alloys – weldability comparable to austenitic SS • Commercially pure titanium – readily welded- extra care to prevent contamination from atmosphere (oxygen, nitrogen)

  31. Summary – Welding for Food Industry • Technology well established for making structurally sound welds • Greatest challenge is hygienic surface considerations, i.e.- welds free from surface defects- surface finishes comparable to base metal- control weld discoloration to levels acceptable for end application

More Related