1 / 25

High-linearity W-band Amplifiers in 130 nm InP HBT Technology

High-linearity W-band Amplifiers in 130 nm InP HBT Technology Robert Maurer 1 , Seong-Kyun Kim 1 , Miguel Urteaga 2 , and Mark J. W. Rodwell 1 UC Santa Barbara 1 Teledyne Scientific Company 2. Motivation. 1-50 GHz High-Dynamic-Range Dual-Conversion Receiver.

milesi
Download Presentation

High-linearity W-band Amplifiers in 130 nm InP HBT Technology

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. High-linearity W-band Amplifiers in 130 nm InP HBT Technology Robert Maurer1, Seong-Kyun Kim1, Miguel Urteaga2, and Mark J. W. Rodwell1 UC Santa Barbara1 Teledyne Scientific Company2

  2. Motivation 1-50 GHz High-Dynamic-Range Dual-Conversion Receiver 100 GHz IF for widely tunable receiver bandwidth System dynamic range limited by IF chain IP3 & noise

  3. Design Goals System Requirements: High IIP3 > 24 dBm (100 GHz, >5 GHz BW) Gain > 6 dB Preferably with: Low Noise Figure Limited chip space/power consumption

  4. Design Strategy How do we achieve such high IP3 at 100 GHz? Approach: High speed 130 nm InP HBT technology Common emitter Pseudo-differential 2nd Harmonic output short-circuit Strong inductive degeneration Sacrifices gain for linearity Partly converges noise & S11 tuning

  5. TSC 130 nm InP HBTs Extremely high-speed technology How does this contribute to linearity? High speed: 13.5 dB MAG/MSG at 100 GHz (2 mA/μm of LE) High maximum available/stable gain Can sacrifice gain for linearity: inductive emitter degeneration. Degeneration also converges tuning for optimum noise and minimum S11

  6. Pseudo-Differential Single-ended Single-ended design: Ground Via Inductance prevents true RF ground Power supply lines de-tune output network Poor power supply isolation Instability, unwanted interstage coupling Vcc power supply line stub tuning Out True differential design: Provides RF virtual ground Must be stable for differential and common-mode Emitter stub likely capacitive in common-mode In Differential Out- Out+ Pseudo-differential design: No common-mode instability problem Power-supply is virtual ground In- In+ Emitter Stub Rbias -Vee

  7. 2nd Harmonic Short Circuit High-linearity: Want linear gain at design frequency ωo Don’t want 3rd order distortion IM3 near design frequency ωo What about 2nd order distortion IM2 at frequency 2ωo? ? IM2 itself is out-of-band, but mixing with fundamental adds extra cubic term to Vout 2nd harmonic tone contributes to IM3, degrades IP3

  8. 2nd Harmonic Short-Circuit λ/4 transmission line: open circuit at ωo short circuit at 2ωo Eliminates IM2, which removes an IM3 mechanism ~2-3 dB IP3 improvement

  9. IC layout Degenerated HBT Amplifier layout collector base 4-finger HBT input balun Emitter inductance 2nd harmonic short

  10. Die layout Input & output baluns: single-ended on-wafer probing Back-to-back balun test structure for de-embedding Overall Die: 1.1 mm x 0.72 mm Differential Amplifier: 0.46 mm x 0.47 mm Back-to-back Baluns S21 = -2.4 dB @ 100 GHz PDC = 200 mW (100 mA, 2V)

  11. S-Parameters S21 S11, S22, S12 Simulated: amplifier without baluns Measured: amplifier with balunsDe-embedded: measurements corrected to remove balun attenuation Measured S21 of 6-7 dB, close to simulation

  12. Noise Figure Measurements (scalar calibration: frequency ripple) Measured noise figure of 7-8.5 dB, close to simulation

  13. IP3 Measurements OIP3 is 21-22 dBm, 4-5 dB lower than simulation

  14. Comparison 350 nm Si BiCMOS1 180 nm Si CMOS2,3 250 nm GaN HEMT4 150 nm GaN HEMT5 CB AlGaAs/GaAs HBT6 100 nm InGaAs HEMT7 This Work Linearized InP HBT8 100 nm InP HEMT9 130 nm InP HBT (This Work) Very few reported mm-wave high linearity amplifiers High speed InP/InGaAs transistors pushing frequency limits O. Nizhnik, et. al. APMC 20071, M. Zavarei, et. al. ICECS 20112, R. Huang, et. al. APCCAS 20143, W. Chang, et. al. APMC 20134, K. Kobayashi, et. al. JSSC 20165, Y. Kwon, et. al. M&GW Letters 19966, F. Canales et. al. IMS 20137, K. Kobayashi, et. al. JSSC 19998, K. Nishikawa, et. al. IMS 20069

  15. High-Linearity W-band Amplifier 100 GHz IFA for mm-wave dual conversion receiver Enabled by high-speed 130 nm InP HBTs S21 of 6.4 dB, OIP3 of 22 dBm, Noise figure of 7 dB OIP3/PDC ratio of 0.79 at 100 GHz Among first reported W-band high-linearity amplifier results Thanks to Teledyne Scientific & Imaging for IC fabrication!

  16. Thank you!!

  17. Amplifier Design (Receiver) Input balun base collector 4 x 5 μm per cell 2nd harmonic short emitter inductive line

  18. 2md generatin design (simulated) Increased cell size + Reduced current density = Improved performance

  19. Pseudo-Differential Single-ended approach: Power supply lines detune output network Poor power supply isolation  instability, inter-stage coupling True differential approach: Power-supply virtual ground prevents coupling & de-tuning Potential for common-mode instability problems Pseudo-differential approach: No common-mode instability Power-supply is virtual ground

  20. IC layout Degenerated HBT Amplifier layout base collect 4-finger HBT input balun Emitter inductance 2nd harmonic short

  21. 2-tone W-band Measurements On-wafer 2-tone W-band IP3 measurement testbench constructed from WR-10 waveguide components Fundamental tone f1 generated w/ PNA & freq. extender heads Fundamental f2 generated w/ synthesizer, a doubler, and a tripler Fundamentals combined with a “magic tee” combiner W-band output downconverted to 1 GHz IF Fundamental output & 3rd harmonic tone observed with spectrum analyzer

  22. 2-tone W-band Measurements

  23. 2-tone IP3 Measurements IP3 measurements performed at f1 = 94, 96, 98, 100 GHz f2 kept 100 MHz above f1

  24. High-Linearity W-band Amplifier 100 GHz IF Amplifier in dual conversion receiver 6.4 dB gain, 15.5 dBm IIP3 (Δ 100 MHz) at 100 GHz 6.8 dB Noise Figure @ 95 GHz OIP3/PDC ratio of 0.79 Among first reported results for IP3 in W-band

More Related