1 / 16

Fabry-Perot cavity for the Compton polarimeter

Fabry-Perot cavity for the Compton polarimeter. Goal: 10- 100 m J/pulse @ 5MHz repetition rate & small diameter ≈ 50 m m (c.f. P. Schuler’s talks). Gain  10000. Fabry-Perot cavity: Principle (HERA cavity, cw laser). e beam. L. Polar. Circ. Polar. Lin.

mcdowellm
Download Presentation

Fabry-Perot cavity for the Compton polarimeter

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Fabry-Perot cavity for the Compton polarimeter Goal: 10-100 mJ/pulse @ 5MHz repetition rate & small diameter ≈ 50mm (c.f. P. Schuler’s talks)

  2. Gain 10000 Fabry-Perot cavity: Principle (HERA cavity, cw laser) e beam L Polar. Circ. Polar. Lin. When nLaser =n0c/2Lresonance • But :Dn/nLaser = 10-11 for Gain=104 laser/cavity feedback • Done by changing the laser frequency

  3. Some of the advantages of using a FP cavity • Compact (& cheap) system compared to a laser of same power (500W in average) • Laser power small outside the cavity: full power only at the electron-laser IP • no thermal effects producing parasitic birefringence & high quality frequency controlled beam accurate control of the laser beam polarisation

  4. Proposal: Cavity filled with a pulsed laser for a Compton polarimeter at FLC ≈5MHz / ≈10 nJ/pulse Electron beam Ti:sa oscillator 500 fs-1ps Pulse laser Fabry-Perot cavity with Super mirrors • A priori impossible because the laser frequency width • Dn ≈1/(1ps)=1012Hz for picosecond laser (c.f. 3kHz cavity banwidth) • In fact possible with mode lock lasers • Jones et al. Opt. Lett. 27 (2003) 1848, Jones at al. Phys. Rev. Lett. 15 (2001) 3288, • Hood et al. Phys. Rev. A64 (2004)033804, Potma et al. Opt. Lett. 28 (2003)1835

  5. Mode lock laser Dt=1ps ≈10 ns t Fourier transform→superposition of N longitudinal laser mode – in phase Dn~1012 Hz=1/(1ps) n Available laser pulse energy: 1-10nJ cavity Gain ≈104 If F.P. cavity length = laser cavity length all modes are also resonant modes of the FP cavity

  6. Cavity gain R.J. Jones et al. Opt. Lett. 27 (2003) 1848 • Pulse width limited by dispersion in the super-mirror coatings (Nb round trips=F/(2p) ≈ 5000 for F=30000  Gain ≈10000): circulating pulse gets broader and broader power loss when overlapped to the incoming pulses (constructive interferences reduced) Width : 300fs-1ps for gain=104

  7. Reduction of the laser beam size at the IP • To get a 50 mm laser beam size at the electron-laser beam IP • Use of a quasi-concentric cavity (mirror curvature radius ≈ half cavity length) • BUT,mechanical tolerance mm & mradneeded on relative mirror positions • Active feedback on relative mirror position needed (c.f. LIGO & VIRGO where nm tolerances are reached)

  8. Present status of FP cavities filled with fs pulses • Power amplification ≈ 120 and cavity Finesse ≈ 300 for pulse width 2-3ps (Potma et al. Opt. Lett. 28 (2003)1835 ) • Proposed R&D: • Reach aFinesse ≈ 30000in a first step • And using a quasi-concentric FP cavity in a second step

  9. Cavities in operation (for Compton polarimetry) • CEBAF (N. Falletto, NIM A459(2001)412): F≈24000 • HERA (upstream the HERMES experiment): F≈30000 • Installation: 2003 summer • Laser & controllers dismounted after synch. rad. damages (huge, generated by 2 new dipoles in HERMES) • Presently: strong shielding and re-mounting • after 1 year of radiation, cavity finesse is still the same and locked again …

  10. ellipsometer 4 motorised miroirs bellow Optique input ligne HERA CAVITY

  11. 2003 installation shielding (3 mm pb) HERA CAVITY

  12. Conclusion • Proposal: a high finesse FP cavity filled with a pulse laser to produce 100mJ/pulse @5MHz • Will contribute to a high precision on the polarisation measurement • This proposition make sense if the polarisation is to be measured bunch by bunch • If not, commercial laser with low rep. rate & high pulse energy do exist • But, this R&D may also be useful for other applications related to FLC (e.g. polarised positrons)

  13. Laser/cavity feedback • similar to cw laser case (Jones et al., Opt. Comm.175(2000)409) • Stabilisation channels, e.g. MIRA (Coherent) Ti:sa oscillator • 3 channels: 2 PZT mounted 2 mirrors & output coupler mounted on translation stage • High frequency correction signal by an EOM if required • Phase velocity & group velocity must be matched to the cavity (bothpulse-round-trip/pulse-repetition matching and frequency matching are required) • A priori not a problem for 0.3-1ps pulse width but precise feedback techniques are known if needed

  14. Aservissements

More Related