1 / 12

How to Tram a Mill Head

How to Tram a Mill Head. Why is tramming a mill head important?. Ensures Tool is ____________ to table surface in both the x and y directions. Ensures that milled surfaces are mutually _____________________.

javan
Download Presentation

How to Tram a Mill Head

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. How to Tram a Mill Head

  2. Why is tramming a mill head important? • Ensures Tool is ____________ to table surface in • both the x and y directions. • Ensures that milled surfaces are mutually • _____________________. • Prevents __________________________pattern from forming on milled surfaces. Un-trammed Mill Head Trammed Mill Head

  3. Tools for Tramming a Mill • Dial Indicator (Fig. A) • Mill Wrench (Figure C) from the mill Figure A Dial Indicator for chuck Figure C Mill Wrench

  4. Tramming about the X-axis(Side View Tilt of Mill Head) • Process: • 1.1 Loosen the three clamping _________ as shown in Figure 1 • 1.2 To adjust the head, turn the _____________________on the top of the mill as shown in Figure 2 Figure 1 Clamp bolts on mill for Y-axis adjustment Figure 2 Adjusting bolt for X-axis tramming

  5. 1.3 Adjust the head to the _______ on the mill protractor as shown in Figure 3 by turning the adjusting bolt • 1.4 Attach the ___________ __________________to the chuck as shown in Figure 4 • 1.5 Raise _____________/______________ Chuck so that the indicator contacts the table surface • 1.6 Adjust the _______________/____________ height until the indicator is preloaded • with .005 - .010” of travel Figure 3 X-axis protractor on mill Figure 4 Dial indicator installed on chuck

  6. 1.7 Position the _________________ at the front of the table as shown in Figure 5 • 1.8 Zero the ____________ ________________by turning the dial • housing • 1.9 Rotate the ____________ so the indicator is at the back of the table • 1.10 Read the _________________ and determinewhich way the _________ needs to be moved • a. A negative reading (____________________) means the head must be tilted up • b. A positive reading (_____________________________) • means the head must be tilted down Figure 5 Indicator positioned at the front of the table

  7. 1.11 Adjust the head so the difference between • the __________ and _______________ ____________is no greater than • .003” • Adjust out ______ the difference between the two dial indicator measurements at a time • 1.12 Tighten the ___________________ bolts • 1.13 Recheck the front and rear measurements to • make sure the head did not move when • tightening the _________________ • _________.

  8. Tramming about the Y-axis (Front View Tilt of Mill Head) • Process: • 2.1 Loosen the __________ clamping bolts as shown in Figure 1a • 2.2 To adjust the head, turn the ________________ bolt on the top of • the mill as shown in Figure 2a Figure 1a Clamp bolts on mill for Y-axis adjustment Figure 2a Adjusting bolt for Y-axis tramming

  9. 2.3 Adjust the head to the __________ on the mill _____________________ as shown • in Figure 3a by turning the adjusting bolt • 2.4 Attach the _________ ___________________to the chuck as shown in Figure 4a • 2.5 Raise Table/Lower Chuck so that the indicator contacts the _________ ______________. Figure 3a X-axis protractor on mill Figure 4 Dial indicator installed on chuck

  10. 2.6 Adjust the table/chuck height until the • indicator is preloaded with ___________” • of travel • 2.7 Position the indicator at the _________ side of • the table as shown in Figure 5a • 2.8 Zero the dial indicator by turning the ________ • housing • 2.9 Rotate the __________ so the indicator is at the • left side of the table • 2.10 Read the _________________and determine • which way the _________ needs to be moved • a. A negative reading (ccw needle • rotation) means the head must be • rotated __________. • b. A positive reading (cw needle rotation) • means the head must be rotated ______________. Figure 5a Indicator positioned at the front of the table

  11. 2.11 Adjust the head so the difference between • the front and rear readings is no greater than • _____________” • a. Adjust out _______ the difference between the two dial indicator measurements at a time • 2.12 Tighten the _________________ ________. • 2.13 Recheck the _________ and __________ • measurements to make sure the head did not move • when tightening the clamping bolts.

  12. Helpful Hints • Make small adjustments and always watch the indicator. • A good adjustment is ________ of what the dial indicator • reads. • This will prevent over adjusting the head. • Think about what is happening as the indicator is moving. • This will help determine which way the head needs to be moved • __________ needle motion indicates the table is getting lower, • or the angle between the mill head and that side of the table is • less than ______ degrees. • __________ needle motion indicates the table is getting higher, • or the angle between the mill head and that side of the table is • greater than ________ degrees.

More Related