1 / 16

SIS 300 Magnet Design Options

SIS 300 Magnet Design Options. SIS 200 / SIS 300 main magnets. Cos n  magnets; cooling with supercritical Helium GSI 001 existing magnet built at BNG measured in our test facility 6 T straight dipole prototype is going to be built at IHEP 4.5 T curved dipoles

gerik
Download Presentation

SIS 300 Magnet Design Options

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. SIS 300 Magnet Design Options

  2. SIS 200 / SIS 300 main magnets • Cos n magnets; cooling with supercritical Helium • GSI 001 • existing magnet built at BNG • measured in our test facility • 6 T straight dipole • prototype is going to be built at IHEP • 4.5 T curved dipoles • actual design (change to FODO lattice) • prototype is going to be built at INFN • Quadrupoles • no design yet

  3. GSI 001: Dipole Parameters • RHIC dipole • Superconducting wire: • NbTi-Cu (1:2.25) • filament diameter 6 mm • twist pitch 13 mm • no coating • Rutherford cable • no core • Coil • phenolic spacer • Cu wedges • Yoke • Hc= 145 A/m • 6.35 mm laminations • RHIC type dipole GSI 001 • Superconducting wire: • NbTi-Cu (1:2.25) • filament diameter 6 mm • twist pitch 4 mm • Stabrite coating • Rutherford cable • 2 x 25µm stain- • less steel core • open insulation • Coil • stainless steel collar (G11 keys) • G11 wedges • Yoke • Hc= 33 A/m, 3.5% Silicon • 0.5 mm laminations, glued

  4. GSI 001

  5. 1T/s 2T/s 3T/s 4T/s 1T 6,9W ± 3W 15,3W ± 3W 28,6W ± 3W 44,3W ± 3W (43%) (19%) (10%) (7%) 27W by heater* 41W by heater* 13,8 J/cycle 15,3 J/Cycle 19 J/Cycle 22,2 J/Cycle 2T 7,6W ± 3W 16,3W ± 3W 30,8W ± 3W 52,1W ± 3W (40%) (18%) (10%) (6%) 38W by heater* 57W by heater* 30,4 J/cycle 32,6 J/Cycle 41 J/Cycle 52,1 J/Cycle 3T 7,6W ± 3W 15,9W ± 3W 30,1W ± 3W 53,2W ± 3W (39%) (19%) (10%) (6%) 28W by heater* 56W by heater* 45,6 J/cycle 47,7 J/Cycle 60,2 J/Cycle 79,8 J/Cycle 4T 7,1W ± 3W 17,0W ± 3W 34,0W ± 3W quench (42%) (17%) (9%) 40W by heater* 56,8 J/cycle 68 J/Cycle 90,7 J/Cycle *by heater; means an inexact additional measurement using the he ater power measurement in the distribution box ( ± 10W) Calorimetric Loss Measurements (C.Schröder) -

  6. SIS 300 6 T Dipole • Central field: 6 T • Ramp rate: 1 T/s • Length: 1 m • Inner coil diameter: 100 mm • Two layers: inner: 4 blocks/outer: 3 blocks • Cooling: supercritical helium • Interlayer cooling channel • No holes in Kapton • Optimized end parts • Appropriate Ra of about 300 µ • Available in May 2008

  7. Conductor for SIS 300 Same outer dimensions and number of strands as the cable for the outer layer of the LHC dipole

  8. SIS 300 dipole: thermal analysis, margins

  9. Wire and Cable R&D • Quench energy measurements for • different Ra in liquid helium (CERN) • Development of wires with CuMn • interfilamentary matrix • (INTAS/INFN) • Optimization of heat treatment to • adjust Ra (BNL) • Time dependent magnetization • measurements (Twente)

  10. SIS300 Lattice Redefinition FBTR SIS 300 Lattice Doublet Lattice based on short straight dipoles New SIS 300 Lattice FODO Lattice based on long (and short) curved dipoles Small ring circumference and matching to SIS100 geometry requires FODO lattice in SIS300 and curved dipole magnets. Advantages a) chromaticity correction without significant DA reduction b) slow extraction with reasonable s.c. septum strength (P.Spiller, Fair Monthly, June 2007)

  11. 4.5 T curved dipole

  12. 4.5 T curved dipole

  13. 4.5 T curved dipole; Thermal analysis

  14. 4.5 T curved dipole; Thermal analysis

  15. 4.5 T curved dipole; Thermal analysis

  16. 4.5 T curved dipole; Thermal analysis

More Related