1 / 23

Integrated Receivers

Integrated Receivers. July 23, 2010. Matt Morgan, Rick Fisher, and Tod Boyd. Analog/Digital/Photonic Receiver Program.

gazit
Download Presentation

Integrated Receivers

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Integrated Receivers • July 23, 2010 • Matt Morgan, Rick Fisher, and Tod Boyd

  2. Analog/Digital/Photonic Receiver Program • To develop receivers and wide bandwidth data transport systems which are lower cost, more compact, more reliable, lower weight, more reproducible, and more stable than the best current systems. • To integrate the conversions from RF to baseband, from analog to digital, and from copper to fiber into a single compact package. • To digitize the signal as close to the antenna feed as possible • this inevitably involves transferring some functionality from analog hardware to the digital domain.

  3. Integrated Receiver Concept

  4. Three-Probe Planar OMT With Integrated LNAs • The incoming signals from some arbitrary number of probes in a circular waveguide are digitized independently and recombined with calibrated weighting coefficients to synthesize accurate polarizations. • Corrects for all amplitude and phase errors of the probe geometry as well as the receiver chains attached to them. • Prototypes shown at the left are for X-Band (8-12 GHz)

  5. DOMT Gain Matrix Representation • Gain matrix relates sky signal vector to output voltage vector: • or • where

  6. Moore-Penrose Pseudo-Inverse Provides a Least-Squares Fit • Direct inversion is not possible (unless N=2), but we can estimate • where

  7. Four Channel Downconverter for Testing the DOMTs

  8. Laboratory Measurement Setup

  9. Polarization Results Isolation (Linear) Axial Ratio (Circular)

  10. Flex Ribbon Thermal Transition • copper traces on 5-mil thick Kapton substrate • lithography sufficient for 3 mm band application • easy to parallelize • smaller, lighter, and cheaper than stainless steel coax or waveguide • shorter (physically and electrically) for the same thermal isolation

  11. Predicted Results: 15-300K Transitions for 50 Dual-Polarized Beams… *Not including the flanges, or the extra height of the dewar.

  12. Digital Sideband Separating Mixer With Integrated ADCs L-Band Module Digital Outputs Analog Inputs Analog Side Digital Side ADCs IF Channels RF Board

  13. Digital Sideband-Separating Mixer (DSSM) • I- and Q-channels digitized and recombined with calibrated complex weighting coefficients. • Corrects for LO, RF, and IF analog amplitude and phase errors. • Extremely stable design: 50 dB sideband-suppression without re-calibration over a 12 °C temperature change. • No increase in digital data rate: requires two ADC's with half the sample rate for a given processed bandwidth. 28°C 40°C

  14. Designed for Calibration Stability • Short electrical paths, elimination of standing waves, and the lack of intermediate cabling and connectors lead to smooth, stable complex gain curves. • Sideband suppression >52 dB in the passband. • Measurement performed six days after calibration. • Only calibrated 10 points across the band – 80% of the points shown use interpolated calibration coefficients.

  15. Snapshot of L-Band Spectrum on the GBT

  16. Internal ADCs Introduce No Measurable Interference expected clock harmonic (12.5 minute integration)

  17. LNA Design and Construction at the CDL • July 23, 2010 • Matt Morgan, Rick Fisher, and Tod Boyd

  18. Chip and Wire IF Amplifiers for ALMA Band 6

  19. Band 6 IF Amplifier Fabrication • Resistors, capacitors, and substrates installed by an outside vendor (Advanced Control Components) • CRYO3 FETs from NGST and MAP FETs from HRL installed here • Final tuning and pair-matching is performed here with cold-testing by an experienced technician in the Band 6 group (Mike Lambeth). • Similar units and techniques used for EVLA production...

  20. 300 Amplifiers Complete, About 50 To Go...

  21. MMIC LNA Development (35nm NGC process)

  22. New MMIC Designs in Fabrication

  23. New MMIC Designs in Fabrication • Eric has also developed LNA designs for 67-95 GHz and 68-116 GHz bandwidths. • We are also experimenting with hybrid approaches: • MMIC partial-LNA with an off-chip quartz matching network • discrete-FET first-stage plus MMIC second-third-fourth-stage

More Related