1 / 13

Cold tests of irradiated FE-I4 at CERN

Cold tests of irradiated FE-I4 at CERN. M. Menouni , A.Rozanov (CPPM - d'Aix-Marseille Université). Outlook. The test set-up and the test conditions Default configuration parameters Digital tests Noise Occupancy tests and Low temperature effects

ervin
Download Presentation

Cold tests of irradiated FE-I4 at CERN

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Cold tests of irradiated FE-I4 at CERN M. Menouni, A.Rozanov (CPPM - d'Aix-Marseille Université)

  2. Outlook • The test set-up and the test conditions • Default configuration parameters • Digital tests • Noise Occupancy tests and Low temperature effects • Effects of PrmpVbp and Amp2VbpFol on the Noise at low temperature • Effect of the tuning at low temperature • Conclusion Cold tests of irradiated FE-I4

  3. Test Set up • Single board FE-I4-B number 165 irradiated in 2012 at CERN PS with 24 GeV protons close to the region of end of columns at 400 MRad • USBpix board with gray flat cable to single chip board • Typical consumption at ambient temperature is : • Vdda=2.5v Idda=430 mA • Vddd=2.5v Iddd=181 mA • Temperature regulated inside the freezer FARK 3130A with dry air flow • Noise measured with NoiseOcc scan usually with 10**5 pixel headers. Cold tests of irradiated FE-I4

  4. Default configuration • Chip configuration: • The threshold is set to 3000e at ambient temperature • FEI4b.irradiated.chip.165.tuned.3000e.TOT8.cfg.root from 17.04.2013 • in fact the configuration file corresponds to a non-tuned chip • Threshold Scan gives : • Mean=3030 • Sigma=381 • Noise= 105 +/- 15 Cold tests of irradiated FE-I4

  5. Digital Tests • Digital_Test good for nominal configuration parameters: Amp2Vbpf=100 • Very High noise at small value of Amp2Vbpf=5 • block the discriminator, so the 400 MRad beam spot is clearly seen. Amp2Vbpf = 100 Amp2Vbpf = 5 Cold tests of irradiated FE-I4

  6. Noise Occupancy tests • Noise Occupancy scan is compatible with the Digital Test • For nominal value of Amp2Vbpf (100) ~No noise at room temperature • For low value of Amp2Vbpf (=5) • Strong Noise at room temperature • correlated with Beam Spot • In this test 64501 hits/10**5 headers Amp2Vbpf = 100 Amp2Vbpf = 10 Cold tests of irradiated FE-I4

  7. Noise Occupancy tests at T=-22 C • At -22 C and for nominal configuration Amp2Vbpf (=100) • the Noise Occupancy is higher than the noise at room temperature • The level of noise is still acceptable • For low value of Amp2Vbpf (5) • High level of noise • correlated with Beam Spot • In this test 43764 hits/10**5 headers Amp2Vbpf = 100 Amp2Vbpf = 5 Cold tests of irradiated FE-I4

  8. Effect of low temperature • Nominal Configuration: • PrmpVbp = 43 • Amp2VbpFol = 26 • Noise increases for low temperature • For nominal value of Amp2Vbpf=100 : • Noise starts to increase at T~-10 C • At T=-23 C Typical 3000 hits/10**5 headers • The noise still present even for Amp2Vbpf = 255 Cold tests of irradiated FE-I4

  9. Effect of PrmpVbp at low temperature • Nominal Configuration: • PrmpVbp = 43 • Amp2VbpFol = 26 • PrmpVbp is the bias of the peampstage • Increasing PrmpVbp from 43 to 96 does not help to reduce the noise • Increase the consumption of the Preamp stage • Vdda current consumption increases from 430 mA (nominal) to 640 mA • 30% increase of power Cold tests of irradiated FE-I4

  10. Effect of Amp2VbpFol at low temperature • Amp2VbpFol is the bias of the Amp2 follower stage • Decreasing Amp2VbpFol from 26 to 1 reduces the noise • but the noise level remains high even for the highest value of Amp2Vbpf (255) Cold tests of irradiated FE-I4

  11. Low temperature effect for Tuned chip (*) The threshold tuned with the nominal configuration where the Amp2Vbpf=100 The threshold depends on the Amp2Vbpf We have to tune the chip for each Amp2Vbpf value changing ! Cold tests of irradiated FE-I4

  12. Low temperature effect for Tuned chip • Test is done with Nominal Configuration: • PrmpVbp = 43 and Amp2VbpFol = 26 • At low temperature of -26 °C, the threshold is tuned to 3000 e- for the whole array of the irradiated chip • The noise occupancy is reduced drastically compared to the one for the un-tuned case at low temperature Cold tests of irradiated FE-I4

  13. Conclusion • Noise occupancy tests are carried out on the FE-I4 chip 265 irradiated with 24 GeV proton to 400 Mrad • Below T=-10 °C, noise increase at nominal setting in few pixels • Partly correlated with irradiated region of the chip • At low values of Amp2Vbpf linear increase of the noise when lowering the temperature • At low temperature, Increasing the PrmpVbp to 96 or decreasing Amp2VbpFol from 26 to 1 help to reduce the noise • However, the noise level remains high even for the highest value of Amp2Vbpf (255) • Despite this level of noise, the threshold was tuned at 3000 e- for the whole pixel array at low temperature • The noise occupancy is reduced drastically compared to the one for the un-tuned case at low temperature • More details in E-log: https://atlpix01.cern.ch/elog/FE-I4_SEU_measurements/302 Cold tests of irradiated FE-I4

More Related