1 / 12

Design Example

Calculate the support forces,. R 1 = 2500 , R 2 = 7500 lb. The critical location is at the fillet,. M A = 2500 x 12 = 30,000 lb-in. 32 M. 305577. Mc.  a =. Calculate the alternating stress,. =. =. I. π d 3. d 3. Determine the stress concentration factor. D. r. = 1.5. = .1.

Download Presentation

Design Example

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Calculate the support forces, R1= 2500, R2= 7500 lb. The critical location is at the fillet, MA= 2500 x 12 = 30,000 lb-in 32M 305577 Mc a= Calculate the alternating stress, = = I πd 3 d 3 Determine the stress concentration factor D r = 1.5 = .1 Kt = 1.7 d d 10,000 lb. Design Example 6˝ 6˝ 12˝ A rotating shaft is carrying 10,000 lb force as shown. The shaft is made of steel withSut = 120 ksi and Sy = 90 ksi. The shaft is rotating at 1150 rpm and has a machine finish surface. Determine the diameter, d, for 75 minutes life. Use safety factor of 1.6 and 50% reliability. d D = 1.5d A R1 R2 r (fillet radius) = .1d m= 0

  2. Using r = .1and Sut = 120 ksi, q (notch sensitivity) = .85 Csurf = A (Sut)b = 2.7(120)-.265 = .759 0.3 in. < d ≤ 10 in. Csize = .869(d)-0.097 = .869(1)-0.097 = .869 Design Example Assume d = 1.0 in Kf= 1 + (Kt – 1)q = 1 + .85(1.7 – 1) = 1.6 Calculate the endurance limit Cload = 1 (pure bending) Crel = 1 (50% rel.) Ctemp= 1 (room temp) ′ Se = Cload Csize Csurf Ctemp Crel (Se) = (.759)(.869)(.5x120) = 39.57 ksi

  3. 39.57 ( ) log ⅓ .9x120 86250 ( ) Sn 39.57 = = 56.5 ksi 106 Sn 56.5 305577 n = a= = .116 < 1.6 = = 305.577 ksi Kfa 1.6x305.577 d 3 So d = 1.0 in. is too small Se ( ) .9Sut log ⅓ Assume d = 2.5 in N ( ) Se Sn = All factors remain the same except the size factor and notch sensitivity. 106 Using r = .25and Sut = 120 ksi, q (notch sensitivity) = .9 Kf= 1 + (Kt – 1)q = 1 + .9(1.7 – 1) = 1.63 Se =36.2 ksi → Design Example Design life, N = 1150 x 75 = 86250 cycles Csize = .869(d)-0.097 = .869(2.5)-0.097 = .795

  4. 36.2 ( ) log ⅓ .9x120 86250 ( ) Sn 36.20 = = 53.35 ksi 305577 a= 106 = 19.55 ksi (2.5)3 Sn 53.35 n = = 1.67 ≈ 1.6 = Kfa 1.63x19.55 d=2.5 in. Check yielding Sy 90 n= 2.8 > 1.6 okay = = Kfmax 1.63x19.55 Design Example Se =36.2 ksi →

  5. 6˝ 12˝ d D = 1.5d A R1 R2 = 7500 Sn r (fillet radius) = .1d 56.5 n = Calculate an approximate diameter = .116 < 1.6 = Kfa 1.6x305.577 Sn 56.5 n = → d = 2.4 in. = = 1.6 So d = 1.0 in. is too small Kfa 1.6x305.577/d 3 Check the location of maximum moment for possible failure Design Example – Observations So, your next guess should be between 2.25 to 2.5 Mmax (under the load) = 7500 x 6 = 45,000 lb-in MA (at the fillet) = 2500 x 12 = 30,000 lb-in But, applying the fatigue stress conc. Factor of 1.63,Kf MA = 1.63x30,000 = 48,900 > 45,000

  6. Fillet r 4 = .16 = 25 d Kt = 1.76 D 35 = = 1.4 d 25 Example A section of a component is shown. The material is steel with Sut = 620 MPa and a fully corrected endurance limit of Se = 180 MPa. The applied axial load varies from 2,000 to 10,000 N. Use modified Goodman diagram and find the safety factor at the fillet A, groove B and hole C. Which location is likely to fail first? Use Kfm = 1 Pm = (Pmax + Pmin) / 2 = 6000 N Pa = (Pmax – Pmin) / 2 = 4000 N

  7. Calculate the alternating and the mean stresses, Pa 4000 a= 1.65 = 52.8 MPa Kf = A 25x5 Pm 6000 m= = 48 MPa = A 25x5 Fatigue design equation a m 1 Infinite life = + 1 n Sut 52.8 48 Se n = 2.7 → = + n 180 620 Example Using r = 4and Sut = 620 MPa, q (notch sensitivity) = .85 Kf= 1 + (Kt – 1)q = 1 + .85(1.76 – 1) = 1.65

  8. d 5 → Kt= 2.6 = = .143 w 35 Using r = 2.5and Sut = 620 MPa, q (notch sensitivity) = .82 Calculate the alternating and the mean stresses, Pm 6000 m= = 40 MPa = A 30x5 Pa 4000 a= 2.3 = 61.33 MPa Kf = A (35-5)5 1 61.33 40 n = 2.5 → = + n 180 620 Example Hole Kf= 1 + (Kt – 1)q = 1 + .82(2.6 – 1) = 2.3

  9. Using r = 3and Sut = 620 MPa, q (notch sensitivity) = .83 Calculate the alternating and the mean stresses, Pm 6000 m= = 41.4 MPa = A 29x5 Pa 4000 a= 2.1 = 58.0 MPa Kf = A (35-6)5 1 58.0 41.4 n = 2.57 → = + n 180 620 Example Groove r 3 = .103 = 29 d → Kt= 2.33 D 35 = = 1.2 d 29 Kf= 1 + (Kt – 1)q = 1 + .83(2.33 – 1) = 2.1 The part is likely to fail at the hole, has the lowest safety factor

  10. Fa= (Fmax – Fmin) / 2=7.5 lb. Fm= (Fmax + Fmin) / 2=22.5 lb. Ma=7.5 x 16 = 120 in - lb Mm=22.5 x 16 = 360 in - lb 32Ma 32(120) Mc a= = = 23178.6 psi = I πd 3 π(.375)3 32Mm 32(360) Mc m= = 69536 psi = = I πd 3 π(.375)3 Example The figure shows a formed round wire cantilever spring subjected to a varying force F. The wire is made of steel with Sut = 150 ksi. The mounting detail is such that the stress concentration could be neglected. A visual inspection of the spring indicates that the surface finish corresponds closely to a hot-rolled finish. For a reliability of 99%, what number of load applications is likely to cause failure.

  11. A95= .010462d 2 (non-rotating round section) dequiv= √ A95 / .0766 = .37d = .37 x.375 = .14 1 23178.6 69536 n = .7< 1 → a → m = + 1 n 24077 150000 = + Finite life n Sut Se Find Sn, strength for finite number of cycle a m 23178.6 69536 Sn = 43207 psi → 1 → = 1 + = + Sut Sn Sn 150000 Example Calculate the endurance limit Csurf = A (Sut)b = 14.4(150)-.718 = .394 Cload = 1 (pure bending) Ctemp= 1 (room temp) Crel= .814 (99% reliability) dequiv= .14 < .3 → Csize = 1.0 Se = Cload Csize Csurf Ctemp Crel (Se) = (.394)(.814)(.5x150) = 24.077 ksi

  12. 24.077 ( ) log ⅓ .9x150 N ( ) 24077 = → 43207 106 Se ( ) .9Sut log ⅓ N ( ) Se Sn = 106 Example N = 96,000 cycles

More Related