1 / 33

Site Calibration for 3D GPS Operations

Site Calibration for 3D GPS Operations. Presenter Name. GPS Site Calibration. Site reconnaissance Control point availability GPS base station location Performing the Calibration. Control point availability. Control points are measured to “calibrate” the site for GPS-based systems

york
Download Presentation

Site Calibration for 3D GPS Operations

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Site Calibration for 3D GPS Operations Presenter Name

  2. GPS Site Calibration • Site reconnaissance • Control point availability • GPS base station location • Performing the Calibration

  3. Control point availability • Control points are measured to “calibrate” the site for GPS-based systems • Do control points exist on site? • Check the site plans for control point lists and locations • You need a minimum of 3 and 5 or more are recommended • For more information, contact: • Land Surveyor • Engineering firm

  4. GPS base station locations – considerations • Obstructions • Setup GPS base station antenna with 360° view of the sky. If limited try to set up with clear visibility to the south. • GPS 55° latitude limit • Glonass 65° latitude limit • Avoid sources of multipath (deflection of the GPS satellite signal) • Chain link fence • Trees • Flat, reflective surfaces – metal roofs, glass windows, water, etc • Setup GPS base radio link for maximum broadcast range • Elevate the radio antenna to increase range • Correct antenna (high gain and low gain) • Avoid sources of RF interference (Microwave, Power lines, etc)

  5. GPS Site Calibration • What is it… • Requirements

  6. GPS Coordinates NEE GPS Site Calibration • What is a site calibration? • A measurement procedure that defines the relationship between GPS coordinates and local coordinates • GPS in Latitude, Longitude, and Ellipsoid Height • Local Coordinates in Northing, Easting, Elevation (MSL) • We are pairing coordinates on a sphere surface and to those on a flat planar surface

  7. = GPS observation = Control Point GPS Site Calibration • Why is a site calibration required? • Allows GPS-based rover systems to work in your local site coordinate system • What is needed for site calibration • Onsite control base on local coordinates

  8. GPS Site Calibration • The calibration locally adjusts the • Projection • Includes shift grids, projection grids, datum grid • Includes Azimuth orientation (e.g.North or South) • Datum • Site Calibration is comprised of 2 parts • Horizontal adjustment • Rotate, Translate, & Scale • Vertical adjustment • Block shift & Tilted Plane • Geoid

  9. GPS Site Calibration • Measuring a Site Calibration will assume • Projection – Transverse Mercator • Datum – WGS84 • If you want to use an alternative to this, then a DC file containing that information should be created and used as the starting point e.g. State Plane etc. • Can then be localized through site calibration

  10. Horizontal Translation • Points shifted X & Y • Same Amount & Direction • 1 Control Point

  11. Horizontal Rotation • Rotation about project centroid • 2 control points

  12. Horizontal Scale • Ratio • GPS to Local Coordinates • 2 Control Points

  13. Residuals • Residuals • Best effort translation between pairs (Control & WGS-84) • SCS900 has a Tolerance for Calibration • Value should be 50% of acceptable project tolerance • Tolerance used to test calibration result worst residual

  14. Calibration Requirements • Single point site calibration Requirements • Requires a single, 3D control point – known or “arbitrary” • Single point defines coordinate system orientation • Used when control does not exist • Recommended for initial site topos and for quick stockpile or volume topos etc • Recommend measuring control points to tie to design reference frame later • Not recommend on long linear projects = GPS observation

  15. = GPS observation = Control Point Calibration Requirements • Multi-point site calibration Requirements • Minimum of 3 (3D) control points • Recommend 5+ control points with good geometry for better results • Combination of horizontal and vertical points - Minimums • 3 horizontal control points & 3 vertical control points – or – • 1 vertical + 3 horizontal + Geoid model • Used when control exists and references a design frame

  16. Control Point Locations • 3 points • will work, but yields only 3 baselines • Geometry could be weak • Control should encompass the entire site

  17. Control Point Locations • 4 Points • Better, 6 baselines • 4th point - independent height check • Geometry is stronger

  18. Control Point Locations • Optimal control- • Multiple control points • Geometry strongest, balanced • Points encompass the site. • This example - 7 points, 18 baselines.

  19. Control Point Locations • Control point network geometry is key = Poor network geometry = Ideal network geometry • Enclose the project area with control • More control points and good network geometry can improve site calibration results and identify problems early

  20. Tilted Plane • Tilted Plane • Effectively models the effect of the local Geoid i.e. local variations in gravity over the site • Minimizes height residuals on control points after block shift • User selectable when to occur in SCS900 • SCS900 has a minimum of 3 points, default is 5 • With only 3 points there is no check and it will zero all residuals to create the tilted plane • Occurs after 2 points in Survey Controller to eliminate height residuals after block shift • SCS900 and Survey Controller will only agree when the tilted plane has been applied in both

  21. Block Shift and Tilted Plane ProcessIn Cross Section View

  22. Details of how this works • Measured Points • Provided local coordinates • The difference between them • Some high, some low compared to average shift • Block Shift from measured to local using average shift • Rotate i.e. Tilt the plane through the measured points to minimize residuals and get a best fit of measured control to local control • In an ideal world we would get a perfect fit • We don’t have an ideal world so we get residuals after the tilted plane – those residuals dictate whether we are in tolerance for the Site Calibration or not.

  23. Geoids • Trimble GeoData folder added in SCS900 v2.3 • Geoids will apply at Site Level • Store multiple Geoids in Trimble Geodata folder • If no Geoids exist in the Trimble Geodata folder then you will not be asked this question

  24. Geoids • Should I use a Geoid model? • Geoids will never hurt • Geoids will allow you to go outside your project calibration • Geoids allow for fewer vertical control points • Provides better detection of errors in control • Recommended on long linear projects

  25. h N Geoid Height (GEOID03) Ellipsoid (WGS84) Geoid Geoids • A geoid height is the separation between the Ellipsoid and the Geoid at any location on the earths surface H = Orthometric Height h = Ellipsoidal Height (WGS84) H = h - N N = Geoid Height (GEOID 03) TOPOGRAPHIC SURFACE H A B

  26. Geoids • Geoid Model (Nm) • Approximates Geoid • Geoid Values (N) • Computed from BM Elevations (h-H=N) • ∆N at each Control Point

  27. Geoids • Tilted Plane through ∆N

  28. Shift Grids • SCS900 now supports SHIFT GRIDS • There are three different types of Shift Grids in Europe • Belgium and Netherlands use SHIFT GRID FILES • UK uses PROJECTION GRID FILES • France uses DATUM GRID FILES

  29. Shift Grids • SHIFT GRID FILES • A standard projection is used to get grid coordinates and then the shift grids are applied to get the correct national coordinates.  One .sgf file contains both northings and eastings shifts • PROJECTION GRID FILES • A standard projection is used to get grid coordinates and then the shift grids are applied to get the correct national coordinates.  One .pgf file contains northings and another .pgf file contains eastings shifts • DATUM GRID FILES • The shift is applied before the projection.  One .dgf file contains the datum shift

  30. GPS Site Calibration • Improving my calibration results • Continue to calibrate on additional control points • Change tolerance • Edit Calibration Components after measuring all control points for the calibration by switching on/off Hz or VT components… • Careful, it is extremely risky to remove one component of a point unless Horizontal and Vertical components of control were established under separate processes

  31. Moving the GPS base station • Before calibration – no problem • After calibration – location requirement • Must be moved to control point • Control used during the calibration • Control measured before moving based and using calibration • Same rules for calibration obtained under VRS

  32. Conclusion • In conclusion, remember these key points • Good Base Station location for good observables • Adequate number of control points (5+) • Good Geometry among control points

  33. Questions?

More Related