1 / 47

CHAPTER 4 BASEBAND PULSE TRANSMISSION

CHAPTER 4 BASEBAND PULSE TRANSMISSION. 4.1 Introduction 4.2. Matched Filter 4.3 Error Due to Noise 4.4 Intersymbol Interference (ISI). Outline. In Ch.3 – methods for digital transmission of analog information bearing signals

Download Presentation

CHAPTER 4 BASEBAND PULSE TRANSMISSION

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. CHAPTER 4BASEBAND PULSE TRANSMISSION Digital Communication Systems 2012 R.Sokullu

  2. 4.1 Introduction 4.2. Matched Filter 4.3 Error Due to Noise 4.4 Intersymbol Interference (ISI) Outline Digital Communication Systems 2012 R.Sokullu

  3. In Ch.3 – methods for digital transmission of analog information bearing signals In Ch.4 – methods for digital transmission of digital information using baseband channel Digital data – broad spectrum; low-frequency components; Transmission channel bandwidth – should accommodate the essential frequency content of the data stream Channel is dispersive channel is noisy – control over additive white noise (old problem..) received signal pulses are affected by adjacent symbols (new problem) – intersymbol interference (ISI); major source of interference; Distorted pulse shape (new problem) - channel requires control over pulse shape 4.1 Introduction Digital Communication Systems 2012 R.Sokullu

  4. Digital Communication Systems 2012 R.Sokullu

  5. Main issue to be discussed: Detection of digital pulses corrupted by the effect of the channel We know the shape of the transmitted pulse Device to be used – matched filter Digital Communication Systems 2012 R.Sokullu

  6. 4.1 Introduction 4.2. Matched Filter 4.3 Error Due to Noise 4.4 Intersymbol Interference (ISI) Outline Digital Communication Systems 2012 R.Sokullu

  7. Basic task – detecting transmitted pulses at the front end of the receiver (corrupted by noise) Receiver model 4.2 Matched Filter Digital Communication Systems 2012 R.Sokullu

  8. Details • The filter input x(t) is: • where • T is an arbitrary observation interval • g(t) is a binary symbol 1 or 0 • w(t) is a sample function of white noise, zero mean, psd N0/2 The function of the receiver is to detect the pulse g(t) in an optimum manner, providing that the shape of the pulse is known and the distortion is due to effects of noise = To optimize the design of a filter so as to minimize the effects of noise at the filter output in some statistical sense. Digital Communication Systems 2012 R.Sokullu

  9. Designing the filter • Since we assume the filter is linear its output can be described as: • where • g0(t) is the recovered signal • n(t) produced noise • This is equal to maximizing the peak signal-to-noise ratio: instantaneous power in the output signal average output noise Digital Communication Systems 2012 R.Sokullu

  10. we have to define the impulse response of the filter h(t) in such a way that the signal-to-noise ratio (4.3) is maximized. So, Digital Communication Systems 2012 R.Sokullu

  11. Let us assume that: - G(f) - FT of the signal g(t); - H(f) – frequency response of the filter then: FT of the output signal g0(t)= H(f).G(f), or sampled at time t=T and no noise Digital Communication Systems 2012 R.Sokullu

  12. Next step is to add the noise. What we know is that the power spectral density of white noise is: Thus the average power of the output noise n(t) is: Digital Communication Systems 2012 R.Sokullu

  13. Substituting, So, given the function G(f), the problem is reduced to finding such an H(f) that would maximize η. Digital Communication Systems 2012 R.Sokullu

  14. We use Schwartz inequality which states that for two complex functions, satisfying the conditions: the following is true: and equality holds iff: Digital Communication Systems 2012 R.Sokullu

  15. In our case this inequality will have the form: and we can re-write the equation for the peak signal-to-noise ratio as: Digital Communication Systems 2012 R.Sokullu

  16. Remarks: • The right hand side of this equation does not depend on H(f). • It depends only on: • signal energy • noise power spectral density • Max value is for: Digital Communication Systems 2012 R.Sokullu

  17. Let us denote the optimum value of H(f) by Hopt(f). To find it we use equation 4.10: The result: Except for a scaling coefficient k exp(-2πfT), the frequency response of the optimum filter is the same as the complex conjugate of the FT of the input signal. Digital Communication Systems 2012 R.Sokullu

  18. In the frequency domain: knowing the input signal we can define the frequency response of the filter (in the frequency domain) as the FT of its complex conjugate. In the time domain… Definition of the filter functions: Digital Communication Systems 2012 R.Sokullu

  19. Take inverse FT of Hopt(f): and keeping in mind that for real signals G*(f) = G(-f): Digital Communication Systems 2012 R.Sokullu

  20. So, in the time domain it turns out that the impulse response of the filter, except for a scaling factor k, is a time-reversed and delayed function of the input signal This means it is “matched” to the input signal, that is why this type of time-invariant linear filters is known as “matched filter” NOTE: The only assumption for the channel noise was that it is stationary, white, with psd N0/2. Digital Communication Systems 2012 R.Sokullu

  21. A filter matched to a pulse signal g(t) of duration T is characterized by an impulse response that is time-reversed and delayed version of the input g(t): Time domain: hopt(t) = k . g(T-t) Frequency Domain: Hopt(f) = kG*(f)exp(-j2πfT) Properties of Matched FiltersProperty 1: Digital Communication Systems 2012 R.Sokullu

  22. A matched filter is uniquely defined by the waveform of the pulse but for the: - time delay T - scaling factor k Property 2: Digital Communication Systems 2012 R.Sokullu

  23. Property 3: • The peak signal-to-noise ratio of the matched filter depends only on the ratio of the signal energy to the power spectral density of the white noise at the filter input. using the inverse FT Digital Communication Systems 2012 R.Sokullu

  24. The integral of the squared magnitude spectrum of a pulse signal with respect to frequency is equal to the signal energy E (Rayleigh Theorem) so substituting in the previous formula we get: • After substitution of (4.14) into (4.7) we get the expression for the average output noise power as: Digital Communication Systems 2012 R.Sokullu

  25. we finally get the following expression: and Digital Communication Systems 2012 R.Sokullu

  26. From (4.20) we see that the dependence of the peak SNR on the input waveform g(t) has been completely removed by the matched filter. So, in evaluating the ability of a matched-filter receiver to overcome/remove additive white noise we see that all signals with equal energy are equally effective. We call the ratio E/N0 signal_energy-to-noise ratio (dimensionless) The matched filter is the optimum detector of a pulse of known shape in additive white noise. Conclusion: Digital Communication Systems 2012 R.Sokullu

  27. 4.1 Introduction 4.2. Matched Filter 4.3 Error Due to Noise 4.4 Intersymbol Interference (ISI) Outline Digital Communication Systems 2012 R.Sokullu

  28. In this section we will derive some quantitative results for the performance of binary PCM systems, based on results for the matched filter. We consider the BER performance for a rectangular baseband pulse using and integrate and dump filter for detection. 4.3 Error Rate Due to Noise Digital Communication Systems 2012 R.Sokullu

  29. The model: • We assume • binary PCM system based on polar NRZ signaling (encoding) • symbols 1 and 0 are equal amplitude and equal duration • channel noise is modeled as AWGN w(t) with zero mean and psd N0/2 • the received signal, in the interval 0 ≤ t ≤ Tb can be represented as: white noise Digital Communication Systems 2012 R.Sokullu amplitude

  30. also it is assumed that the receiver has accurate knowledge of the starting and ending times of each pulse (perfect synchronization); the receiver has to make a decision whether the pulse is a 1 or a 0. the structure of the receiver is as follows: Digital Communication Systems 2012 R.Sokullu

  31. The filter is matched to a rectangular pulse of amplitude A and duration Tb. The resulting matched filter output is sampled at the end of each signaling interval. The channel noise adds randomness to the matched filter output. Details: Digital Communication Systems 2012 R.Sokullu

  32. For the channel model we are discussing (AWGN), integrating the noise over a period T is equal to creating noise with Gaussian distribution with variance σ02 = N0 T/2, where N0 is the noise power in Watts/Hz. Digital Communication Systems 2012 R.Sokullu

  33. If we consider a single symbol s(t) of voltage V passing through the detector with additive noise n(t) then the output of the integrator y(t) will be: symbol contribution noise contribution Digital Communication Systems 2012 R.Sokullu

  34. Then the probability density of the integrated noise at the sampling point is: • A detection error will occur if the noise sample exceeds - VT/2. • The probability for such an event is calculated from (1) Digital Communication Systems 2012 R.Sokullu

  35. substituting we can write the expression for the probability of error as: complementary error function Digital Communication Systems 2012 R.Sokullu

  36. The probability of error can also be expressed in terms of the signal energy as follows: • As 0 and 1 are equiprobable the result for receiving a logic 0 in error will be the same only in this case the noise sample will be exceeding +VT/2. Digital Communication Systems 2012 R.Sokullu

  37. For the special case we are discussing unipolar NRZ the average symbol energy is half that of the logic 1. So the symbol error probability will be: Digital Communication Systems 2012 R.Sokullu

  38. Figure 4.5Noise analysis of PCM system. (a) Probability density function of random variable Y at matched filter output when 0 is transmitted. (b) Probability density function of Y when 1 is transmitted. Digital Communication Systems 2012 R.Sokullu

  39. Unipolar vs Bipolar Symbols • For unipolar symbols as we said the average energy is equal to E0/2. • For bipolar symbols (logic 1 is conveyed by +V, logic 0 – by –V volts) it can be proved that (An example of this is RS-232, where "one" is −5V to −12V and "zero" is +5 to +12V) Digital Communication Systems 2012 R.Sokullu

  40. 4.1 Introduction 4.2. Matched Filter 4.3 Error Due to Noise 4.4 Intersymbol Interference (ISI) Outline Digital Communication Systems 2012 R.Sokullu

  41. ISI is due to the fact that the communication channel is dispersive – some frequencies of the received pulse are delayed which causes pulse distortion (change in shape and delay). Most efficient method for baseband transmission – both in terms of power and bandwidth - is PAM. 4.4 PAM and Intersymbol Interference (ISI) Digital Communication Systems 2012 R.Sokullu

  42. Considered model: • baseband binary PAM system • incoming binary sequence b0 consists of 1 and 0 symbols of duration Tb Figure 4.7 Baseband binary data transmission system. Digital Communication Systems 2012 R.Sokullu

  43. PAM changes this sequence into a new sequence of short pulses each with amplitude ak, represented in polar form as: applied to a transmit filter of impulse response g(t): transmitted signal Digital Communication Systems 2012 R.Sokullu

  44. s(t) is modified by a channel with channel impulse response h(t) random white noise is added (AWGN channel model) x(t) is the channel output, the noisy signal arriving at the receiver front end receiver has a receive filter with impulse response c(t) and output y(t) y(t) is sampled synchronously with the transmitter (clock signal is extracted from the receive filter output) reconstructed samples are compared to a threshold decision is taken as for 1 or 0 Digital Communication Systems 2012 R.Sokullu

  45. Receive filter output is: should have a constant delay t0 here set to 0 The scaled pulse µp(t) can be expressed as double convolution: the impulse response of the transmit filter g(t), the impulse response of the channel filter h(t) (channel) and the impulse response of the receive filter c(t): Digital Communication Systems 2012 R.Sokullu

  46. In the frequency domain we have: where P(f), G(f), H(f) and C(f) are FT of the respective p(t), g(t), h(t) and c(t) The received signal is sampled at times ti= iTb which, taking (4.44) in mind and the norm. condition p(0) = 1 (µ is a scaling factor to account for amplitude changes), can be expressed as: residual effect due to other transmitted pulses contribution of the ith pulse Digital Communication Systems 2012 R.Sokullu

  47. In the absence of noise and ISI we get and ideal pulse (from (4.48) ) y(ti)=µai The ISI can be controlled (reduced) by the proper design of the transmit and receive filter Subject discussed further in the following sections…. Conclusion: Digital Communication Systems 2012 R.Sokullu

More Related