1 / 5

ONT/ONU provisioning in ISAM 7360 FX

ONT/ONU provisioning in ISAM 7360 FX. These slides describe the procedure for how BECS will find and provisioning un-provisioned ONTs and ONUs To goal is to automate the work and reduce human involvement BECS is going through the following steps Recognize un-provisioned ONTs

ulmer
Download Presentation

ONT/ONU provisioning in ISAM 7360 FX

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. ONT/ONU provisioning in ISAM 7360 FX • These slides describe the procedure for how BECS will find and provisioning un-provisioned ONTs and ONUs • To goal is to automate the work and reduce human involvement • BECS is going through the following steps • Recognize un-provisioned ONTs • Allocate ONT interface • Configure generic ONT configuration • Determine ONT model • Configure complete ONT configuration

  2. Recognize un-provisioned ONTs • To recognize new ONTs/ONUs BECS needs to listen for and lookup for “newont” alarms from the OLT. • When a “newont” alarm appear it is published in realtime at a CLI and TL1 session. • When the alarm appear it always contains serial number information • The “show alarm” command also shows open alarms stored in the log. • Through CLI the alarm doesn’t show the ONT serial number • Through TL1 the alarm show the ONT serial number • For BECS to be able to get the full information from an ONT alarm, both in realtime and later on in a log, BECS will use a TL1 session to recognize un-provisioned ONTs/ONUs • A TL1 session will constantly be open towards the elements. • The command “RTRV-COND-PON::ALL:::NEWONT,,;” will ask the OLT for un-provisioned ONTs • Realtime alarms will automatically appear and have the same format. • BECS will constantly look for realtime alarms. • Periodically will also the alarm log be checked to verify no realtime alarms were missed.

  3. Initial ONT configuration • When a new ONT is recognized BECS know the OLT host name, PON interface and serial number • Form the screenshot example • NOIDA-CO-1 • PON-1-1-1-8 • ALCLF9DA6CD2 • BECS will based on this information allocate the first free ONT interface number at the particular OLT and PON interface • Then a generic independent of ONT/ONU type command will be applied • configure equipment ont interface 1/1/1/8/X sernum ALCL:F9DA6CD2 sw-ver-pland unplanned • The OLT will the be able to communicate with the ONT/ONU • The command “show equipment ont interface 1/1/1/8/X detail” will then give the information which ONT/ONU model it is • In the example below it tells this is an ONT of model, I-240E-Q

  4. Configure ONT model • BECS now know which model it is of the ONT/ONU and can do the final configuration including firmware information. • “configure equipment ont interface 1/1/1/8/X sernum ALCL:F9DA6CD2 sw-ver-pland3FE54378AOCI08” • Even additional command for the ONT/ONU model will be added, like • voip-allowed enable • enable-aesenable • fec-up enable • desc1 "MDU-O-24240E-Q" • p2p-enable disable • Finally the ont will be enabled • configure equipment ont interface 1/1/1/8/X admin-state up

More Related