1 / 3

RF COMPONENTS USING OVER-MODED RECTANGULAR WAVEGUIDES FOR THE NEXT LINEAR COLLIDER MULTI-MODED DELAY LINE RF DISTRIBUTIO

INTRODUCTION

tamma
Download Presentation

RF COMPONENTS USING OVER-MODED RECTANGULAR WAVEGUIDES FOR THE NEXT LINEAR COLLIDER MULTI-MODED DELAY LINE RF DISTRIBUTIO

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. INTRODUCTION • The Multi-moded Delay Line Distribution System (MDLDS) was suggested as an alternative for rf pulse compression for the Next Linear Collider (NLC)[1]. MDLDS propagates several modes in a single circular highly over-moded waveguide. This system uses a set of complicated over moded rf components. Most of these components manipulate several modes at the same time. • Manipulation of several modes in a single component is easier in rectangular waveguides. To take advantage of this, we present several rf tapers which maps the modes in circular waveguides into modes in rectangular guides. Three types of tapers are presented: • A taper from circular waveguide to a square waveguide. The circular guide diameter is just big enough to support the TE01 mode. • A taper from circular waveguide to a square waveguide with the circular waveguide diameter big enough to support all modes up to the TE12 mode. • An taper from circular waveguide to a rectangular guide. The circular guide diameter is just big enough to support the TE01 mode. • We describe the application of the first type of tapers to the design of a 90-degree bend for the TE01 mode in circular waveguides. We also present the results of an experimental model for this bend. SIMULATION TECHNIQUE We assumed that all these tapers will be built using wire Electron Discharge Machining (EDM). When tapering from one shape, e.g. a circle, to another shape, e.g., a square, the length of the taper l and the connecting points between the two shapes uniquely define the taper. In cylindrical coordinates a shape i, placed with cylindrical symmetry around the z-axis, can be described by a relation , which gives the radius as a function of the angle f . The taper between two shapes , and is then given by . (1) This taper is compatible with the process of wire EDM when the two heads of the machine are moving synchronously with the same angular speed. More complicated tapers are described by a set of tapers, each have the form of Eq.(1) and cascaded together. All simulations were performed using HP-HFSS [2]. The shapes were plotted using a finite number of points (72 points) using Visual Basic Application (VBA) in AutoCAD [3]. The shapes were then imported into HP-HFSS, and the interpolation described in Eq. (1) was done using the connect function, to generate the solid model. This process was used to design all the tapers described in this work. All tapers were optimized around 11.424 GHz. RF COMPONENTS USING OVER-MODED RECTANGULAR WAVEGUIDES FOR THE NEXT LINEAR COLLIDER MULTI-MODED DELAY LINE RF DISTRIBUTION SYSTEM S. G. Tantawi , N. M. Kroll, And K. Fant, Stanford Linear Accelerator Center, 2575 Sand Hill Rd., Menlo Park, CA, 94025,U.S.A. • We present the design and analysis for a set of smooth transitions from rectangular to circular waveguide that preserves their common reflection symmetries. The S-matrix of the transition connects modes of the same symmetry class, and for a sufficiently adiabatic transition preserves their TE (or TM) character. It is then also non-reflecting and, in the absence of degeneracy, its modal connections are one to one and order preserving. This property enables us to carry out all of the RF manipulations in the more easily handled over-moded rectangular waveguide. As an example, we apply this technique to the design of a 90-degree bend for the TE01 mode in circular waveguides. 3.556 cm 3.81 cm 1.905 cm Type 1: TE01 Circular to Square Taper In this taper the circular waveguide diameter is chosen such that all modes, that have a cut-off frequency above that of the TE01 mode, do not propagate. The square waveguide is just large enough to allow both TE20 and TE02. However, it does not allow the propagation of TE22 and TM22 modes. Because of reflection symmetries, only the two degenerate modes, TE20 and TE02, in the rectangular guide are exited when the incident mode in the circular guide is TE01. The design process for this taper is simply done by increasing the length until the reflection coefficient for the TE01 mode in the circular guide is small enough. Fig. 1 shows the taper design and Fig.2 shows the TE01 mode reflection coefficient for this design. .

  2. 3.81 cm 2.54 cm A straight section. The cross section shape is given by 3.286 cm 2.54 cm 3.696 cm 3.131 cm Field pattern when the circular port is excited by the TE12 mode. The TE30 in the rectangular port couples perfectly to it. coupling of the TE01 in the circular guide to spurious modes in the square guide. At the design length for Type 2 taper. 2.2 Type 2: TE01 and TE12 Circular to Square Taper. The circular waveguides used in the long delay lines of the MDLDS uses three different modes. These modes are the TE01, and the two polarizations of the TE12 mode [1]. In this type of tapers, the diameter of the circular waveguide is increased to 5.08 cm to support the TE12 mode. Equivalently, the width of the square waveguide was increased to 4.491 cm to support the TE30 and the TE03 modes. At this width the square waveguide supports both the TE22 and the TM22 modes,. These modes have the same reflection symmetries as the TE01 mode in circular waveguide and the TE02 and TE20 in rectangular waveguide. The design process of this taper was simply increasing the length until the coupling from the circular TE01 mode to the square TE22 and TM22 is small enough. The length required is 10.16 cm. Fig. 3 shows the coupling of the TE01 in the circular guide to spurious modes in the square guide. At this length the coupling between modes in the circular guide to modes in the square guide is one to one with a transmission coefficient that is better than –0.017 dB over a 0.5 GHz bandwidth around 11.424 GHz. The modes connect to each other according to the table. 2.2 Type 3: TE01 Circular to TE02 Rectangular Taper. In several applications one would want to convert the TE01 mode in the circular guide to a single polarization of the TE02 mode in the square guide. Modifying the square waveguide to a rectangular waveguide to break the degeneracy between the TE02 and TE20 modes could do this. However, in this case, the length of the taper required to achieve an adiabatic transition to a single mode in the rectangular guide is excessive (approximately 17.78 cm). Instead, we construct this taper from three sections as shown in the figure. The taper from the circle to the intermediate shape produce scatters the TE01 mode into two modes M1 and M2 in the intermediate section. Also the taper between the rectangular waveguide to the intermediate shape scatter the rectangular mode TE02 into M1 and M2. The lengths of both tapers are adjusted such that the coefficients of the scattered modes M1 and M2 are the same from both sides. Since M1 and M2 propagate with deferent phase velocities in the intermediate section, the length of that section could be adjusted so that the circular TE01 mode get completely converted into the rectangular TE02 mode. The simulated performance of that taper is shown. 3.81 cm Application of Type 1 taper. A 90 degree bend for the TE01 in circular guide is realized through tapering from that mode into a square guide thus exciting the two polarization of the TE20 mode in the square guide. The bend is then performed in an over moded rectangular waveguide.

  3. Wrap-Around Mode Converter for Tap-off, and extraction, tested to 320MW

More Related