1 / 27

Simulation of Thermal Effects for the Analysis of Micro Laser Assisted Machining

Simulation of Thermal Effects for the Analysis of Micro Laser Assisted Machining. By Saurabh R Virkar Under guidance of Dr. John A Patten ICOMM 2010 Venue: University of Wisconsin, Madison. Introduction:.

sylvie
Download Presentation

Simulation of Thermal Effects for the Analysis of Micro Laser Assisted Machining

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Simulation of Thermal Effects for the Analysis of Micro Laser Assisted Machining By Saurabh R Virkar Under guidance of Dr. John A Patten ICOMM 2010 Venue: University of Wisconsin, Madison

  2. Introduction: • Silicon Carbide (SiC) is an advanced engineered ceramic and an alternative to semiconducting Silicon (Si) for operation at elevated temperatures and high power applications. Some of SiC’s beneficial properties include: chemical resistance, high temperature resistance, extreme hardness and high stiffness • Hardness of SiC: 26 GPa • The machining of SiC is difficult due to its high hardness and brittle nature. • Ductile mode µ-LAM has been studied to replace grinding and polishing processes and to increase the material removal rates and maintaining the workpiece surface quality

  3. In µ-LAM, the laser beam passes through the diamond tool, thus heating the surface just below the tool tip in the chip formation zone Diamond tool SiC Schematic of µ-LAM

  4. High Pressure Phase Transformation • The ductile material removal can be attributed to a High Pressure Phase Transformation (HPPT) at the tool-chip interface and the resultant phase is metallic or amorphous • The HPPT occurs due to contact between the sharp tool and workpiece at or below critical depth of cut, i.e., below the ductile to brittle transition

  5. Why Simulations? • Silicon Carbide (SiC) is very expensive semiconductor • Measurement of temperatures at nano-scale is practically not possible • Also the rate of heat transfer and pressures on tool and workpiece can be studied • There is a metallic phase at tool chip interface due to high pressure phase transformation Software used: AdvantEdge version 5.4 • Commercial software for machining solutions in metals developed by Third Wave Systems Inc.

  6. Objective: • To simulate different heating conditions over a temperature range for studying the laser heating effect • To study the change in chip formation, cutting forces and pressures with changes in heating/temperature conditions

  7. Mathematical model: DruckerPrager Yield Criterion: …(1) …(2) Where I1 is first invariant of stress tensor …(3) Where J2 is second invariant of deviatoric stress tensor Hence initial yield stress is given by: …(4) For uniaxial stress, σ2 = σ3 = 0 and also σc = σ1 = H= 26 GPa σt = H/2.2 = 11.82 GPa (for ceramics) Hence, К= 16.25 GPa and Drucker-Prager coefficient (α) = 0.375

  8. Simulation Model Workpiece Material properties:

  9. Workpiece Thermal properties: Thermal Softening Curve * Note: The values for temperature from 20° C to 1500° C which is thermal cutoff temperature are estimated based on various references. The value for melting temperature of SiC is also estimated from a reference.

  10. Tool parameters and geometries: Tool geometry: The -45⁰ rake angle creates a high pressure sufficient to accommodate the HPPT, thus the chip formation zone is conducive for ductile deformation Tool Properties:

  11. Simulated Thermal Effect Conditions • Tooltip Boundary Condition • Rake and Clearance face Heated Boundary Condition • Workpiece Boundary Condition

  12. Tooltip Boundary Condition A thermal boundary condition was provided on the tool tip about 2µm on rake and clearance face from cutting edge

  13. Workpiece Boundary Condition A thermal boundary was provided on the workpiece top surface

  14. Simulation parameters • Temperature range of the simulation work: • 20° C, 700° C, 1500° C, 2200° C and 2700° C where 1500° C is the thermal cutoff point in the material model. • From 20° C till 1500° C, the thermal softening curve has a 3rd order polynomial fit in the material model • From the thermal cutoff point (1500° C) till melting point (2830° C) the curve is linear

  15. Constraints: • AdvantEdge does not provide for the direct incorporation of the laser heat source, thus the heating effect is modeled with these thermal conditions • For this study, the crystalline dependency of the brittle behavior of SiC is not included in the model Note: The temperature scale changes in each figure, as the minimum temperature is set slightly above and below the boundary condition temperature

  16. Tooltip Boundary Condition at 20° C

  17. Tooltip Boundary Condition at 2200° C

  18. Rake and Clearance face at 20° C

  19. Rake and Clearance face heated at 2200° C

  20. Workpiece Boundary Condition at 20° C

  21. Workpiece Boundary Condition at 2200° C

  22. Results:

  23. Force plots (All simulation conditions)

  24. Cutting Pressure Plots (All Boundary Conditions)

  25. Conclusions: • The thermal effects successfully simulated the laser heating effect • Decrease in cutting forces and pressures is studied with increase in temperature • The change in chip formation due to change in temperature above and below the thermal cutoff point is studied is studied

  26. On-going work: • To determine the effect of interaction between temperature and compressive stress on the cutting forces and pressures from room temperature till melting point of SiC • 3D scratch test simulations for comparison with experiments

  27. Acknowledgement Support from NSF (CMMI-0757339) Support from ThirdWave Systems

More Related