1 / 16

AIAA 2002-5531 OBSERVATIONS ON CFD SIMULATION UNCERTAINTIES

AIAA 2002-5531 OBSERVATIONS ON CFD SIMULATION UNCERTAINTIES. Serhat Hosder, Bernard Grossman, William H. Mason, and Layne T. Watson Virginia Polytechnic Institute and State University Blacksburg, VA Raphael T. Haftka University of Florida Gainesville, FL

Download Presentation

AIAA 2002-5531 OBSERVATIONS ON CFD SIMULATION UNCERTAINTIES

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. AIAA 2002-5531OBSERVATIONS ON CFD SIMULATION UNCERTAINTIES Serhat Hosder, Bernard Grossman, William H. Mason, and Layne T. Watson Virginia Polytechnic Institute and State University Blacksburg, VA Raphael T. Haftka University of Florida Gainesville, FL 9th AIAA/ISSMO Symposium on Multidisciplinary Analysis and Optimization 4-6 September 2002 Atlanta, GA

  2. Introduction • Computational fluid dynamics (CFD) as an aero/hydrodynamic analysis and design tool • CFD being used increasingly in multidisciplinary design and optimization (MDO) problems • Different levels of fidelity • from linear potential solvers to RANS codes • CFD results have an associated uncertainty, originating from different sources • Sources and magnitudes of the uncertainty important to assess the accuracy of the results

  3. Objective of the Paper • To illustrate different sources of uncertainty in CFD simulations, by a careful study of • 2-D, turbulent, transonic flow in a converging-diverging channel • complex fluid dynamics problem • affordable for making multiple runs • To compare the magnitude and importance of each source of uncertainty • We show that uncertainties from different sources interact • To demonstrate how much uncertainty there may be in similar flow simulations by an informed CFD user

  4. Uncertainty Sources (following Oberkampf and Blottner) • Physical Modeling Uncertainty • PDEs describing the flow • Euler, Thin-Layer N-S, Full N-S, etc. • boundary conditions and initial conditions • geometry representation • auxiliary physical models • turbulence models, thermodynamic models, etc. • Discretization Error • Originates from the numerical replacement of PDEs and continuum boundary conditions with algebraic equations • Consistency and Stability • Spatial (grid) resolution and temporal resolution • Iterative Convergence Error • Programming Errors • Interaction of uncertainties from different sources

  5. Transonic Diffuser Problem Weak shock case (Pe/P0i=0.82) Pe/P0i experiment CFD Strong shock case (Pe/P0i=0.72) Pe/P0i streamlines Separation bubble Contour variable: velocity magnitude

  6. Computational Modeling • General Aerodynamic Simulation Program (GASP) • A commercial, Reynolds-averaged, 3-D, finite volume Navier-Stokes (N-S) code • Has different solution and modeling options. An informed CFD user still “uncertain” about which one to choose • For inviscid fluxes (most commonly used options in CFD) • Upwind-biased 3rd order accurate Roe-Flux scheme • Flux-limiters: Min-Mod and Van Albada • Turbulence models (typical for turbulent flows) • Spalart-Allmaras (Sp-Al) • k- (Wilcox, 1998 version) with Sarkar’s compressibility correction

  7. Grids Used in the Computations Grid 2 y/ht A single solution on grid 5 requires approximately 1170 hours of total node CPU time on a SGI Origin2000 with six processors (10000 cycles) Grid 2 is the typical grid level used in CFD applications

  8. Nozzle efficiency Nozzle efficiency (neff ), a global indicator of CFD results: H0i : Total enthalpy at the inlet  He : Enthalpy at the exit  Hes : Exit enthalpy at the state that would be reached by isentropic expansion to the actual pressure at the exit Throat height

  9. Uncertainty in Nozzle Efficiency

  10. Uncertainty in Nozzle Efficiency Neglect grid 1 results, use Sp-Al, grid 4 results as the comparator to obtain the percentage values Strong Shock Weak Shock

  11. Approximation of Discretization Error by Richardson’s Extrapolation error coefficient order of the method a measure of grid spacing grid level

  12. Major Observations on the Discretization Errors • Grid convergence is not achieved with grid levels that have moderate mesh sizes. For the strong shock case, even with the finest mesh level we can afford, asymptotic convergence is not certain • As a consequence of above result, it is difficult to separate physical modeling uncertainties from numerical errors • Shock-induced flow separation, thus the flow structure, has a significant effect on grid convergence • Discretization error magnitudes are different for different turbulence models. The magnitudes of numerical errors are affected by the physical models chosen.

  13. Error in Geometry Representation Upstream of the shock, discrepancy between the CFD results of original geometry and the experiment is due to the error in geometry representation. Downstream of the shock, wall pressure distributions are the same regardless of the geometry used.

  14. Downstream Boundary Condition Extending the geometry or changing the exit pressure ratio affect: • location and strength of the shock • size of the separation bubble

  15. Conclusions For attached flows without shocks (or with weak shocks), informed users can obtain reasonably accurate results They aremore likely to get large errors for cases with strong shocks and substantial separation Grid convergence is not achieved with grid levels that have moderate mesh sizes (especially for separated flows) The flow structure has a significant effect on the grid convergence It is difficult to isolate physical modeling uncertainties from numerical errors Uncertainties from different sources interact, especially in the simulation of flows with separation

  16. Conclusions • The magnitudes of numerical errors are influenced by the physical models (turbulence models) used • In nozzle efficiency results, • range of variation for the strong shock is much larger than the one observed in the weak shock case (10% vs. 4%) • the error between grid level 2 and grid level 4 can be up to 6% (strong shock) • relative uncertainty due to the selection of the turbulence model can be as large as 9% (strong shock)

More Related