1 / 8

RX10 & RX12 Scissor Lifts - Maximum Productivity,minimum space

RX Scissor Lift - Large capacity with a small footprint.for more <br>information visit us <br>http://www.rielequipment.com/products/rx10_12_scissor_lift_brochure.pdf

Download Presentation

RX10 & RX12 Scissor Lifts - Maximum Productivity,minimum space

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. RX10 & RX12 Scissor Lifts Maximum productivity, minimum space

  2. RX Scissor Lift Large capacity with a small footprint Best-In-Class Drive-On Height Best-In-Class Drive-On Height Best-In-Class Drive-On Height 12 12 12 11 11 11 11 11 in. OTHERS 10 10 10 10 10 10 10 in. RX12 in. 9 9 9 9 9 8.75 in. RX10 8 8 8 8 8 7 7 7 7 6 6 6 6 5 5 5 4 4 Extra-Wide Runways Extra-Wide Runways 3 3 3 2 2 1 1 1 ? Minimize clearance issues Minimize clearance issues 24 in. ? 24 in. runways accept wide vehicles 24 in. runways ? Integrated Air Line Kit Integrated Air Line Kit ? Convenient air source for tools at front and rear Convenient air source ? Convenient air source Convenient air source Velocity Safety Fuses Velocity Safety Fuses Sensor Feedback System* Sensor Feedback System Safety Locks ? Instantaneous shutdown in event of hydraulic failure Instantaneous shutdown ? Sensors keep runway level ? Safely stops if obstructed Sensors keep runway level ? Precision-fi t teeth lock runways at 16 level height positions Precision-fi t teeth ? ? ? ? * Shown with protective cover removed

  3. Louvered Ramps Louvered Ramps Louvered Ramps Two Swing Air Jacks Two Swing Air Jacks Control Panel Control Panel ? 6,000-lb. capacity ? Technicians’ favorite 6,000-lb. capacity ? Prevent wheel spin in wet conditions ? More effective than diamond tread or abrasive strips Prevent wheel spin in ? Complete operation from the console ? Optional PowerSlide, Inflation Station and FIA control Complete operation ? ? RX10LT-IS shown with optional light kit OPTIONAL Pins and Bearings Two Movable Work Steps Two Movable Work Steps Inflation Station Inflation Station ? 12 secure positions ? Lightweight design 12 secure positions ? Chromed pins and tefl on bearings for long life Chromed pins and ? Automatically fi lls or bleeds each tire ? No hanging air lines Automatically fi lls ? ? ? ?

  4. Fast descent speed The hydraulic system speeds lowering times by 50%. The system automatically slows the descent in the last several inches to ensure a soft landing. The fast descent feature is standard with Infl ation Station (IS) models. 0:25 FAST Descent STANDARD 0:50 Swing Air Jacks Hunter Swing Air Jacks add capabilities for lifting vehicles off the runways during alignment procedures and other multi-service operations. Each 6,000-lb. (2722-kg) capacity Swing Air Jack combines low drive-on height with high lifting capacity needed to handle a wide range of vehicles. 133-85-1 – 6,000-lb. Capacity Swing Air Jack Flush-mount installation OPTIONAL Lifts may be fl ush-mounted in a shallow recess. No more worries about lowered vehicles or expensive spoilers! This very tidy installation is ideal for “showcase” shops. No additional charge for fl ush-mount option. Contact your Hunter Sales Representative for details. Add F to any RX model number.

  5. AlignLights system OPTIONAL Hunter’s integrated AlignLights LED lighting system provides a bright and effi cient light source underneath the vehicle. AlignLights automatically turns on when the lift is raised and turns off when the lift is lowered to the fl oor. AlignLights is an ALI-listed accessory. 20-2766-1 – AlignLights system Approach ramp extensions Conversion kits Stage 2 RX approach ramp extensions Drive-thru conversion OPTIONAL OPTIONAL 40 in. kit – 20-2169-1 ? Adds approx. 28 in. to RX12A. ? Includes quick-release pins. 52 in. kit – 20-2498-1 ? For camera sensors ? Includes quick-release pins 12 in. kit – 20-3112-1 ? Standard with RX12A. ? ? ? ? ? 17 in. kit – 20-3113-1 ? Adds approx. 5 in. to RX12A when substituted for 20-3112-1. 50 in. kit – 20-2189-1 ? Adds approx. 38 in. to RX12A. ? Includes quick-release pins. 63 in. kit – 20-2501-1 ? For conventional sensors ? Includes quick-release pins ? ? ? ? ? Standard equipment ? Flush-mounted, full-fl oating slipplates (PowerSlide slipplates on PS and IS models) ? Louvered ramps with built-in wheel stops ? Front wheel stops ? Two wheel chocks ? Built-in, full-length jack rails ? Built-in air line kit ? Stainless steel turnplates ? ? ? (PowerSlide turnplates on PS and IS models) ? ? Two movable work steps (not included with fl ush-mount installations) ? ? ? ?

  6. Hunter offers two fully integrated options to enhance productivity FIA allows WinAlign® aligners to control the lift features for ultimate productivity. Two patented designs offer greater fl exibility and timesaving capabilities. Shown with optional aligner console, sensors, bar code reader, target support brackets, and lights.

  7. P O W E R S L I D E E D I T I O N ? Locks slipplates and turnplates with the touch of a button or automatically through an FIA-equipped aligner* ? ? No more struggles with lock pins ? ? Avoid wear and tear and extend the life of your turnplates of your turnplates ? Yesterday's Technology Minimize trips around the car 1 Mount targets 2 Make adjustments 3 Remove targets 4 Jack vehicle and compensate sensors 5 Lower leveling legs (if equipped) 6 Remove slipplate and turnplate pins 7 Replace slipplate and turnplate pins 8 Raise leveling legs (if equipped) 8 Raise leveling legs (if equipped) 4 5 Jack vehicle and compensate sensors Only 3 Trips! 8 Trips Lower leveling legs (if equipped) 1 6 Remove slipplate and turnplate pins 1 2 2 3 3 4 5 6 7 Replace slipplate and turnplate pins 7 8 I N F L A T I O N S T A T I O N E D I T I O N ? Includes PowerSlide® slipplates and turnplates ? ? Automatically infl ate all four tires simultaneously ? ? Record starting and fi nal pressure* ? ? Hose recoils to keep work area clear ? Printouts show starting and final tire pressures.* Printouts show starting * Requires FIA equipped aligner with WinAlign 10.x software or greater.

  8. Specifications RX Plan View RX12A RX10L RX10 OPTIONAL EXTENDED WHEEL STOP Max. vehicle weight Max. wheelbase 12,000 lbs. (5443 kg) 10,000 lbs. (4536 kg) 10,000 lbs. (4536 kg) LEAVE AMPLE  WORKSPACE  BETWEEN EQUIPMENT AND  LIFT  RACK 11  5/8  IN. (295  mm) 16 IN. (406  mm) surface/flush General service 184/180 in. (4673/4572 mm) 184/180 in. (4673/4572 mm) 171/167 in. (4343/4241 mm) Two-wheel alignment 179/175 in. (4547/4445 mm) 179/175 in. (4547/4445 mm) 166/162 in. (4216/4115 mm) 7  FT.  -­  4  1/2  IN. (2248  mm) FOR RX10  MODELS, 20  FT.  -­  1  1/4 (6128  mm) Four-wheel alignment Min. four-wheel alignment Lowered height Max. lifting height Alignment height Runway width Tread width 158 in. (4013 mm) 158 in. (4013 mm) 158 in. (4013 mm) IN. FOR RX10L MODELS, 21  FT.  -­  2  1/4  IN. (6458  mm) 88 in. (2235 mm) 88 in. (2235 mm) PRIOR  TO  LIFT  INSTALLATION: 88 in. (2235 mm) INSTALL 230VAC,  1  PHASE, 60  HZ  FOR  26 AMP DRAW  NEAR CONTROL CONSOLE  LOCATION. 8.75 in. (222 mm) FOR 10 in. (254 mm) 8.75 in. (222 mm) 90-­150  PSI  (6.2-­10.3  BAR)  SHOP AIR  MUST ALSO  BE  SUPPLIED. RX12A MODELS, 22  FT.  -­  2 (6756  mm) IN. 71 in. (1803 mm) 72 in. (1829 mm) 72 in. (1829 mm) 24  IN. (610  mm) 16 IN. (406  mm) All lock positions 22 IN. (559  mm) 24 in. (609 mm) 39  -­  54 (991  -­  1372  mm) IN. Min. inside 40 in. (1016 mm) Max. outside Air pressure Speed 88 in. (2235 mm) 90-150 psi (6.2-10.3 bar)* See Hunter Sales Representative for details on site requirement. 55 seconds (raise), 25-50 seconds (descent) * 125 psi required for full jack capacity Models RX12AT-IS ? ? ? RX12AT-PS ? RX12AJT RX10T-IS ? ? ? RX10T-PS ? RX10JT Fully Integrated Alignment Infl ation Station PowerSlide slipplates & turnplates ? ? Stainless steel turnplates ? ? ? ? Two 6,000-lb. Swing Air Jacks ? ? ? ? Add F to any RX model number (ex. RX10JFT) Add L to any RX10 model number (ex. RX10LT-IS) Flush-mount Long-deck (RX10 models only) Because of continuing technological advances, specifications, models and options are subject to change without notice. Be sure to check out other Hunter literature for more quality products from Be sure to check out other Hunter literature for more quality products from Hunter Engineering. Hunter Engineering. The Hunter RX10 and RX12A Scissor Lifts have been certifi ed under the program conducted by Automotive Lift Institute (ALI) and ETL Testing Laboratories to comply with Safety Standard ANSI/ALI, ALCTV and Electrical Standard ANSI/UL 201. www.hunter.com 0715HAP7.5M.34 Form 6175-T, 07/15 Copyright © 2015, Hunter Engineering Company Supersedes Form 6175-T, 12/14

More Related