1 / 32

Ethernet Power Supply Controller

Ethernet Power Supply Controller. Ethernet Power Supply Controller (EPSC). The EPSC was intended as a replacement for the PEP 2 Bitbus Power Supply Control chassis The intent was to provide as much commonality as possible with the Bitbus controller

moses-cohen
Download Presentation

Ethernet Power Supply Controller

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Ethernet Power Supply Controller

  2. Ethernet Power Supply Controller(EPSC) • The EPSC was intended as a replacement for the PEP 2 Bitbus Power Supply Control chassis • The intent was to provide as much commonality as possible with the Bitbus controller • The performance was to be equal or better then the Bitbus chassis • Should not cost more then Bitbus controller

  3. The main components to be changed • The DAC used in the Bitbus chassis is obsolete and a new DAC was required. • The Bitbus network is obsolete and it is desirable to convert to Ethernet (10/100 Mb/sec over UTP) • The FPGAs are at end of life and are not good choices for new designs • The 8044 processor is obsolete • Use standard +/-15VDC power supply

  4. The main features to preserve • Size of controller (1U in 19 inch rack) • Power Supply, Transductor, and Interlock connector types and interfaces • Use Bitbus Daughter Boards • Support Bitbus command set • Use existing Bitbus local control board • Support for redundant transductor • All interlocks handled by FPGA, not software • Ability to reset processor without turning off power supply

  5. Desirable improvements • Improved speed and resolution of ADC • Internal Fan to allow true 1U stacking • Air Filter and closed chassis to minimize dirt • Provide option of analog or digital regulation • Magnet Interlock circuit to locate faulted klixons in magnet strings • Extended analog readbacks

  6. Power supply controller functions • Precision current regulation (using PS as voltage source) • Setting and ramping of currents • Readback of current, voltage, and ground current • Ground fault protection • Hardware magnet and power supply protection (no software) • Fault latching and reporting • Simple low cost serial communication to central control

  7. Interface to Standard Components • Power Supplies of many ratings, types and from different vendors • Board range of current transducers (transductors) • Standard cables (Cat 5 UTP and D-sub computer cables)

  8. Current Input Daughter Board Voltage Input Daughter Board 150, 300, and 600 amp Danfysik Transductors > 600 amp Transductors

  9. Local Control Board Allows Local control of Power Supply Voltage or Current Regulation Analog Test Points Same as Bitbus Local Controller

  10. Processor board • Uses 32 bit Motorola Coldfire processor • 512K of flash program memory • 8M of SDRAM memory • Provides Ethernet interface and 3 UARTS • C Libraries and Compiler • Boot loader over Ethernet • TCP/IP stack • Real time operating system (uCOS)

  11. Netburner Mod5282

  12. Sigma Delta ADCs • Two Burr Brown ADS1255 • 24 Bit Sigma-Delta ADC • 6 PPM linearity (corrected to 2 PPM) • Input amplifier provides +/- 12V range • 20 bit effective resolutuion of 10V range at 60 samples/sec • Gain set by oven stabilized zener (0.25 PPM/C) • Gain and offset readings interleaved with data

  13. DAC (PWM) • 8 bit PWM • 32 MHZ clock • 117 KHZ period (274 clocks) • 9 clock minimum ON/OFF period • 24 bit input latch • Forth order digital filter • Output regulated using ADC1

  14. Analog and Digital Regulation • 4 modes of operation • Error Amplifier with DAC reference • Error Amplifier with Local Control reference • Direct PS control with Local Control • Direct PS control with DAC, digital regulation using processor and ADC1

  15. Klixon Fault Location Circuit • Allows klixon fault location in strings of up to 40 klixons • Two circuits per controller • Three wire interface, no active components in radiation areas • Controller senses current in interlock chain after a fault, converts to conductance to locate faulted klixon.

  16. Fan Speed Control • Fan voltage programmable from 5V to 13V • Speed changes from 3000 to 9000 RPM • Voltage at minimum below 90 ° F • Voltage at maximum above 105 ° F • Fan filter on front panel of controller • Fan RPM calculated from current pulses • Air ducted below PC board

  17. Chassis Airflow

  18. Current Status • 2 Prototype units built • 4 Pre-Production units built • 40 Production Units under construction • 30 units for SSRL • 7 units for LCLS injection

  19. Comparison of Bitbus and EPSC Controller Performance Bitbus EPSC Unit Parameter 2 30/60 ADC readings per second 12 3 uV RMS ADC noise (0.1 to 10 Hz) 18 20 Bits Effective number of bits (10V FS) 21 24 Bits DAC resolution * 2 uV RMS DAC noise (0.1 to 10 Hz) * 2 PPM max DAC Linearity 0-10V 0.25 0.25 PPM/°C max ADC temperature stability max 1.0 1.0 PPM/°C typ Daughter card temperature stability typ

More Related