1 / 39

Chapter 10: Ethernet and Fibre Cable

Chapter 10: Ethernet and Fibre Cable. Business Data Communications, 5e. Increase in High-Speed LANs. Extraordinary growth in speed, power, and storage capacity of PCs Increasing use of LANs as computing platforms Examples Server farms Workgroups with “power” requirements

leann
Download Presentation

Chapter 10: Ethernet and Fibre Cable

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Chapter 10: Ethernet and Fibre Cable Business Data Communications, 5e

  2. Increase in High-Speed LANs • Extraordinary growth in speed, power, and storage capacity of PCs • Increasing use of LANs as computing platforms • Examples • Server farms • Workgroups with “power” requirements • High-speed backbones Business Data Communications, 5e

  3. Increase in High-Speed LANs • Fast Ethernet and Gigabit Ethernet • Fibre Channel • High-speed Wireless LANs Business Data Communications, 5e

  4. Characteristics of Some High-Speed LANS Business Data Communications, 5e

  5. Trends Influencing Emergenceof High-Speed LANs • Explosive growth of speed and computing power of PCs • Recognition by MIS organizations of the value and importance of networked computing • Centralized server farms • Power workgroups • High-speed local backbone Business Data Communications, 5e

  6. Traditional Ethernet • Ethernet and CSMA/CD (IEEE 802.3) • Carrier sense multiple access with collision detection • Four step procedure • If medium is idle, transmit • If medium is busy, listen until idle and then transmit • If collision is detected, cease transmitting • After a collision, wait a random amount of time before retransmitting Business Data Communications, 5e

  7. Ethernet MAC Frame Format • Preamble: 7-octet pattern of 0s &1s used to establish bit synchronization. • Start Frame Delimiter (SFD): Indicates actual start of frame. • Destination Address (DA): Specifies the station(s) for which the frame is intended • Source Address (SA): Specifies the station that sent the frame. • Length: Length of LLC data field in octets. • LLC Data: Data unit supplied by LLC. • Pad: Octets added to ensure that the frame is long enough for proper CD operation. • Frame Check Sequence (FCS): A 32-bit CRC, based on all fields except preamble, SFD, and FCS. Business Data Communications, 5e

  8. Ethernet MAC Frame Business Data Communications, 5e

  9. 802.3 Medium Notation • Notation format:<data rate in Mbps><signaling method><maximum segment length in hundreds of meters> • e.g 10Base5 provides 10Mbps baseband, up to 500 meters • T and F are used in place of segment length for twisted pair and fiber Business Data Communications, 5e

  10. 802.3 10BaseX Media Options Business Data Communications, 5e

  11. Bridges • Allow connections between LANs and to WANs • Used between networks using identical physical and link layer protocols • Provide a number of advantages • Reliability: Creates self-contained units • Performance: Less contention • Security: Not all data broadcast to all users • Geography: Allows long-distance links Business Data Communications, 5e

  12. Bridge Functions • Read all frames from each network • Accept frames from sender on one network that are addressed to a receiver on the other network • Retransmit frames from sender using MAC protocol for receiver • Must have some routing information stored in order to know which frames to pass Business Data Communications, 5e

  13. Bridge Operation Business Data Communications, 5e

  14. Makes no modification to content or format of frames it receives; simply copies from one LAN and repeats with exactly the same bit pattern as the other LAN. Should contain enough buffer space to meet peak demands. Must contain addressing and routing intelligence. May connect more than two LANs. Key Aspects of Bridge Function Business Data Communications, 5e

  15. Hubs • Alternative to bus topology • Each station is connected to the hub by two lines (transmit and receive) • When a single station transmits, the hub repeats the signal on the outgoing line to each station. • Physically a star; logically a bus. • Hubs can be cascaded in a hierarchical configuration. Business Data Communications, 5e

  16. Two-Level Hub Topology Business Data Communications, 5e

  17. Layer 2 Switches • Also called a “switching hub” • Has replaced hub in popularity, particularly for high-speed LANs • Provides greater performance than a hub • Incoming frame from a particular station is switched to the appropriate output line to be delivered to the intended destination • At the same time, other unused lines can be used for switching other traffic Business Data Communications, 5e

  18. Ethernet Hubs and Switches • Shared medium hubs • Switched LAN hubs x Business Data Communications, 5e

  19. Advantages of Switched Hubs • No modifications needed to workstations when replacing shared-medium hub • Each device has a dedicated capacity equivalent to entire LAN • Easy to attach additional devices to the network Business Data Communications, 5e

  20. Types of Switched Hubs • Store and forward switch • Accepts a frame on input line • Buffers it briefly • Routes it to appropriate output line • Cut-through switch • Begins repeating the frame as soon as it recognizes the destination MAC address • Higher throughput, increased chance of error Business Data Communications, 5e

  21. Differences Between Switched Hubs and Bridges • Bridge frame handling is done in software. A layer 2 switch performs the address recognition and frame forwarding functions in hardware. • Bridges typically only analyze and forward one frame at a time; a layer 2 switch can handle multiple frames at a time. • Bridges uses store-and-forward operation; layer 2 switches use cut-through instead of store-and-forward operation • New installations typically include layer 2 switches with bridge functionality rather than bridges. Business Data Communications, 5e

  22. Problems With Layer 2 Switches • Broadcast overload • Lack of multiple links • Can be solved with subnetworks connected by routers • However, high-speed LANs layer 2 switches process millions of packets per second whereas a software-based router may only be able to handle well under a million packets per second Business Data Communications, 5e

  23. Layer 3 Switches • Implement the packet-forwarding logic of the router in hardware. • Packet-by-packet switch operates like a traditional router • Forwarding logic is in hardware • Achieves an order of magnitude increase in performance compared to software-based routers • Flow-based switch identifies flows of IP packets that have the same source and destination • Once flow is identified, a predefined route can be established to speed up the forwarding process • Again, huge performance increases over a pure software-based router are achieved Business Data Communications, 5e

  24. Why Use Ethernet for High-Speed Networks? • Negative • CSMA/CD is not an ideal choice for high-speed LAN design due to scaling issues, but there are reasons for retaining Ethernet protocols • Positive • Use of switched Ethernet hubs in effect eliminates collisions • CSMA/CD protocol is well understood; vendors have experience building the hardware, firmware, and software • Easy for customers to integrate with existing systems Business Data Communications, 5e

  25. Fast Ethernet • Refers to low-cost, Ethernet-compatible LANs operating at 100 Mbps • 802.3 committee defined a number of alternatives to be used with different transmission media Business Data Communications, 5e

  26. 802.3 100Base-T Options Business Data Communications, 5e

  27. 802.3 100BaseX Media Options Business Data Communications, 5e

  28. Gigabit Ethernet • Retains CSMA/CD protocol and Ethernet format, ensuring smooth upgrade path • Uses optical fiber over short distances • 1-gbps switching hub provides backbone connectivity Business Data Communications, 5e

  29. Gigabit Ethernet Media Options Business Data Communications, 5e

  30. Driven by increased network traffic Increased number of network connections Increased connection speed of each end-station (e.g., 10 Mbps users moving to 100 Mbps, analog 56k users moving to DSL and cable modems) Increased deployment of bandwidth-intensive applications such as high-quality video Increased Web hosting and application hosting traffic 10-Gbps Ethernet Business Data Communications, 5e

  31. No expensive, bandwidth-consuming conversion between Ethernet packets and ATM cells is required Combination of IP and Ethernet offers quality of service and traffic policing capabilities that approach those provided by ATM A wide variety of standard optical interfaces have been specified for 10-Gbps Ethernet, optimizing its operation and cost for LAN, MAN, or WAN applications 10-Gbps Ethernet vs ATM Business Data Communications, 5e

  32. Physical Layer Options for 10-Gbps Ethernet Business Data Communications, 5e

  33. Example 100-Mbps Ethernet Backbone Strategy Business Data Communications, 5e

  34. Fibre Channel • Combine the best features of channel and protocol-based technologies • the simplicity and speed of channel communications • the flexibility and inter-connectivity that characterize protocol-based network communications. • More like a traditional circuit-switched or packet-switched network, in contrast to the typical shared-medium LAN Business Data Communications, 5e

  35. Full-duplex links with two fibers per link Performance from 100 Mbps to 800 Mbps on a single link (200 Mbps to1600 Mbps per link) Support for distances up to 10 km Small connectors High-capacity utilization with distance insensitivity Greater connectivity than existing multidrop channels Broad availability (i.e., standard components) Support for multiple cost/performance levels, from small systems to supercomputers Ability to carry multiple existing interface command sets for existing channel and network protocols Fibre Channel Goals Business Data Communications, 5e

  36. Fibre Channel Elements • Nodes • The end systems • Includes one or more N_ ports for interconnection • Fabric • Collection of switching elements s between systems • Each element includes multiple F_ ports • Responsible for buffering and for routing frames between source and destination nodes Business Data Communications, 5e

  37. Fibre ChannelProtocol Architecture • FC-0 Physical Media: Includes optical fiber, coaxial cable, and shielded twisted pair, based on distance requirements • FC-1 Transmission Protocol: Defines the signal encoding scheme • FC-2 Framing Protocol: Defines topologies, frame format, flow/error control, and grouping of frames • FC-3 Common Services: Includes multicasting • FC-4 Mapping: Defines the mapping of various channel and network protocols to Fibre Channel Business Data Communications, 5e

  38. Fibre Channel Media • Media options include shielded twisted pair, video coaxial cable, and optical fiber • Data rates range from 100 Mbps to 3.2 Gbps • Point-to-point link distances range from 33 m to 10 km Business Data Communications, 5e

  39. Fibre Channel Topologies • Fabric/Switched Topology • includes at least 1 switch to interconnect end systems. • may also use multiple switches for a switched network, with switches also supporting end nodes • Point-to-point topology • only two ports, directly connected, with no intervening fabric switches • Arbitrated loop topology • Simple, low-cost topology for connecting up to 126 nodes in a loop. • Operates in a manner roughly equivalent to token ring protocols Business Data Communications, 5e

More Related