1 / 42

Mikhail asiatici 29/08/2014

Development of a SiPM readout circuit and a trigger system for microfluidic scintillation detectors. Mikhail asiatici 29/08/2014. Overview. Introduction Project context System overview LabVIEW interface Features Post processing algorithms Performances PCBs Overview SiPM breakout

jared-mason
Download Presentation

Mikhail asiatici 29/08/2014

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Development of a SiPM readout circuit and a trigger system for microfluidic scintillation detectors Mikhail asiatici 29/08/2014

  2. Overview • Introduction • Project context • System overview • LabVIEW interface • Features • Post processing algorithms • Performances • PCBs • Overview • SiPM breakout • Amplifiers • Power supply

  3. Overview • Measurements • SiPM pulses • Scintillation light • Thick plastic scintillator (tile) • Microchannels with liquid scintillator • SiPM characterization • Conclusions

  4. Project context - Target system • Microfluidicscintillator detector • Multiple photodetectors to allowreconstructionof particletracks with high resolution (60 μm channelpitch) • Verylow light level (1.65 photoelectrons per MIP, in average) A. Mapelli et al. - Scintillation particledetectionbased on microfluidics 1/32

  5. System overview XY table Power supply USB +5 V 65 to 70 V SiPM Trigger(s)/signal(s) A SiPM PC B USB digital oscilloscope C LabVIEW D PMT ext 2/35

  6. project context – sipm vs pmt PMT SiPM A. Mapelli et al. - Scintillation particledetectionbased on microfluidics N. Otte - Silicon Photomultipliers a new device for frontier detectors in HEP, astroparticle physics, nuclear medical and industrial applications 3/32

  7. Project context – xy table Stepper motorscontroller 2 x motorizedlinear stages in XY configuration 4/32

  8. portability + QDC + PC via Ethernet connection? (+ router) + PC via USB 5/32

  9. Labview interface: overview 6/32

  10. Labview interface: features (1) • Eachchannelcanbeindependently • Set as signal source, trigger, temperature or disabled • Connected to any pulse source (PMT, SiPM) • Trigger modes • Self trigger (on any signal channel) • Single external trigger • A functiongeneratorcanemulate a periodic/random trigger • Coincidence trigger with programmable coincidencewindow • Online pulse integralcalculation and histogramgeneration • Several post-processing options available 7/32

  11. Labview interface: features (2) • Waveformscircularbuffer • Online monitoring of the capture • Temperature acquisition • Temperaturesensorwith voltage output • XY table interfacement • Automatic scan of an array of points • Simplifieddefinition of matrices of points • Import/export from/to XML file • Manual control of the XY table 8/32

  12. Labview interface: features (3) • File logging • Events in ROOT format • Settings and scan points in XML format • Automaticallycreatedtogetherwith the ROOT file • Can beread back in LabVIEW to loadscan points and/or capture settings • Performances • Successful capture of up to 37 000 000 events • Event rate up to 9 kHz 9/32

  13. Labview interface: post processing algorithms • Baseline compensation • Pile up rejection • Pile up main cause of eventsbetweensharppeakswithSiPM • Edge-adaptedintegration 10/32

  14. Pcb: overview SiPM (SMD package) PicoScope Low voltage stabilized power supply (4.75 V – 6 V) Optionally -5 V MCX SMD connector USB port LV LV + data Amplifiers 50Ω coaxial cable Step-up switching converter HV LEMO connector 11/35

  15. SMD SiPM adapter board (dimensions in mm) Connector Holes for mechanical support SiPM (Hamamatsu S12571-050P) 12/32

  16. Amplifiers simulations • For SiPM: equivalent model by F. Corsi et al.1 • Parametersfrom one of the devicespresented in the paper (SiPM IRST), with Q = e*M ≈ 200 fC (M ≈ 1.25 x 106 for the devicesreceived) • Amplifier 1: transconductance amplifier + voltage amplifier (single stage from C. Piemonte et al.)2withwide-band voltage-feedback op amp (ADA4817) ≈ 10 mV/pe single stage ≈ 20 mV/pe double stage (slightlyslower) Tsettle5% ≈ 50 – 150 ns (trade gain for speed) Verylow noise (EIN = 4.4 nV/sqrt(Hz)) 1 F. Corsi et al. – Modelling a silicon photomultiplier (SiPM) as a signal source for optimum front-end design 2 C. Piemonte et al. – Development of an automatic procedure for the characterization of silicon photomultipliers 13/32

  17. Amplifiers • Dual supply (+/- 5 V): short J13, J11. • Single supply (+ 5 V): short J12, J10 (like in picture). External 5 V: short J9 (like in picture) • Obtain 5 V fromlinearregulator MCP1700: short J8, and connect at least 6 V on the + 5 V input. • External 5 V: short J9 • Second amplification chainremoved (impossible to stabilize, probablysomepositive feedback effectbetween the two amplification chains) J9 Vbias J8 + 5 V J10 - 5 V (optional) J11 J12 GND J13 14/32

  18. Single stage amplifier on evaluationboard PD Vbias Connected to GND (useful to short –IN to GND with a jumper) GND + 5 V 15/32

  19. Power supply board • Step-up switching voltage regulator, to avoid the need of an high-voltage supplyjust for SiPMbiasing • Output voltage tuning • Integrated DAC with serial interface • Digital pins available for a possible future integrationwithe.g. a microcontroller • Potentiometer (here not shown) • Input voltage range: 4.75 V – 6 V • Output voltage range: 65 V – 70 V, 2 mA max • Vop of the availableSiPM: 66.6 V ± 1.3 V • Recommended Vop range: 2.1 V • Same architecture used for SiPMbiasing in the Schwarzschild-Couder CTA Telescope K. Meagher (Georgia Tech) – SiPM Electronics for the Schwarzschild-Couder Telescope (presentation) 16/32

  20. Vbias power supply 4.75 V to 6 V • Short J4: voltage isregulatedwith R4. • Short J3: voltage isregulated by MAX1932 DAC. Default at power up: lowestVbias (around 65.35 V). Use this if youwant to use the USB to SPI bridge (next slide). • J2 is the SPI interface. From top to bottom, pins are nCS, SCLK, MOSI, GND. GND Vbias 17/32

  21. USB to SPI bridge • Withthese connections, the power supplyboardispowered via USB. • Command-line interface • Set Vbiasbetween 65.3 V and 70.3 V with ≈ 20 mV resolution (8 bit) • Turn off voltage conversion (Vbias ≈ 4.5 V) + 5 V from USB GND from USB 18/32

  22. Sipm pulses 5 p.e. Dual stage board ≈ 20 mVpk/p.e. ≈ 800 mV*ns/p.e. (R ≈ 4 kΩ) tr = 12 ns (amplifier limited) tf = 45 ns (mostlySiPMlimited) 4 p.e. 1 p.e. 2 p.e. 3 p.e. 3 p.e. 4 p.e. 5 p.e. 2 p.e. 1 p.e. + afterpulses INFN board ≈ 7 mVpk/p.e. ≈ 100 mV*ns/p.e. (R ≈ 500 Ω) tr ≈ 1 ns (oscilloscope limited) tf= 38 ns (SiPMlimited) 1 p.e. (tr and tf are 10-90% and 90-10% rise and fall time, consideringabsolute value of V) SiPMbiased at 66.7 V 10 mV/div, 20 ns/div 19/32

  23. Measures – sipmcharacterization Self trigger histogram, in darkness 1 p.e. -> primarydark count 2+ p.e. -> primarydark count + crosstalk • Fit with Borel distribution -> • Gain • Crosstalkprobability gain 20/32

  24. Measures – sipmcharacterization Self trigger histogram, in darkness P(crosstalk) proportional to ∆V2 Gain proportional to ∆V V = 68.0 V -> ∆V = 3.5 V V = 66.0 V -> ∆V = 1.5 V V = 66.5 V -> ∆V = 2.0 V V = 65.5 V -> ∆V = 1.0 V V = 67.0 V -> ∆V = 2.5 V V = 67.5 V -> ∆V = 3.0 V 21/32

  25. Measures – sipmcharacterization Slope: Cd+Cq (for SiPM SPICE model) VBD 22/32

  26. Measures – sipmcharacterization 23/32

  27. Measures – sipm temporal characterization Characterization VI inspired by C.Piemonte et al.- Development of an automatic procedure for the characterization of silicon photomultipliers 24/32

  28. Measures – sipm temporal characterization Amplitude vs distance frompreceeding pulse 5 p.e. 4 p.e. 3 p.e. 2 p.e. 1 p.e. Delayedcrosstalk? Primarydark count Afterpulses Afterpulses + crosstalk Measureswith INFN board (leadingedge must be as rapid as possible) 25/32

  29. Measures – sipm temporal characterization Primarydark count -> exponential distribution (distorted due to log binning not normalized) Maximum = 1/DCR, withouteffectfromafterpulses Projection along time axis, log-log scale, log binning Oscilloscope bandwidthlimit Afterpulses: Exponential distribution with tau muchshorter ≈ 10 ns (traplifetime) Fit to findafterpulseprobability. Peak is constant, amplitude increases 26/32

  30. Measures – sipm temporal characterization DCR proportional to ∆V Afterpulseprobabilityproportional to ∆V2 27/32

  31. Measures - setup coincidence trigger 2 x PMT for trigger fibers (not shown) Microchannels (or plastic tile) Amplifiersconnected via coaxcable (not shown) SiPM 28/32

  32. Measures – plastic tile 6 p.e. 0 p.e. 21 p.e. 16 p.e. counts (mV s) 29/32

  33. Measures – microchannels 0 p.e. Meannumber of p.e. (sub-mm channels, trigger and SiPMaligned by eye…) Fit withbranching Poisson distribution, to model SiPMcrosstalk 1 p.e. 2 p.e. Pedestal (no channels) … Gain (mV s per p.e.) counts 9 p.e. (mV s) 30/32

  34. Conclusions • Developed an automaticcharacterization and acquisition system for microfluidic scintillation detectors • Events processing and logging to ROOT file • XY table interfacement • Both light yield (PMT and/or SiPM as photodetectors) and spatial characterization • Compact and portable • Tools for SiPMcharacterization • Confirmedliteratureresults, SiPM excellent photodetectors for low light yield 31/32

  35. perspectives • Electronics • Investigate gain vs bandwidthtradeoff on existingamplifiers, test amplifiersbased on current feedback amplifiers • Integration of all the electronics (amplifiers, bias and USB interface) on a single board – beware of switching noise! • Towards multi channel acquisition • On-boarddigitalization (pulse shapers, fastADCs) and processing (FPGA) • EASIROC • SiPM • Considerothermanufacturers • Investigatetemperatureeffects (expect DCR reduction, VBDreduction, afterpulse time constants increase) • Software • AutomaticSiPMcharacterization (gain, DCR and P(AP) vs V, pulse time constants, Corsi model parameters) • Full waveformdigitalizationenablesendlessprocessingpossibilities • Noise reduction • Discretep.e. histogram (pulse fitting, combine pulse peak and integral, …) 32/32

  36. Thank you

  37. backup

  38. Amplifiers simulations • Amplifier 2: transconductance amplifier + non-inverting amplifier withwide band current-feedback op amp (AD8000) from F. Giordano et al. ≈ 10 mV/pe single stage ≈ 80 mV/pe double stage Tsettle5% ≈ 40 – 60 ns (fast) Higher noise (EIN = 520 nV/sqrt(Hz)) F. Giordano et al. – Tests on FBK SiPM sensor for a CTA-INFN ProgettoPREMIALE demonstrator (presentation) 12/32

  39. Amplifiers performances summary • Gain in the order of 10s mV/pe, time constants in the order of 10s-100s ns • Amplifier 1 lessnoisy • Amplifier 2 faster 13/32

  40. Amplifiers pcb requirements • The PCB ismeant as a test boardfromwhichpossiblyderive a definitive configuration, soitis important to ensure the maximum possible flexibility • For both the configurations, the signal canbeextractedafter single or double stage • For all of the 4 signal sources, the output canbeexctractedbefore/after a decouplingcapacitor • Capacitorperforms on-board AC coupling, but mightresults in signal reflections • Optional dual supply +/- 5 V as an additionalway to produce a signal with no DC component (but maybedecouplingcapacitorisenough) • All the feedback resistors are potentiometers, to allow gain tuning • There isalways a certain degree of gain-bandwidthtradeoff • Avoid saturation for eventswith a highernumber of photoelectrons • Bypassable on-boardlinear voltage regulator • Compare noise with on-board/external voltage regulation 14/32

  41. SMD SiPM adapter board (dimensions in mm) Connector Holes for mechanical support SiPM (Hamamatsu S12571-050P) 15/32

  42. Amplifiers board Jumpers for on-board/external voltage regulationchoice SiPMconnectors: LEMO Output connectors: LEMO Jumpers for single/dual voltage supplychoice Power supply (HV, LV, optional -5 V, GND) 16/32

More Related