slide1 n.
Skip this Video
Loading SlideShow in 5 Seconds..
Examcollection 200-120 Braindumps PowerPoint Presentation
Download Presentation
Examcollection 200-120 Braindumps

Loading in 2 Seconds...

play fullscreen
1 / 7
Download Presentation

Examcollection 200-120 Braindumps - PowerPoint PPT Presentation

Download Presentation

Examcollection 200-120 Braindumps

- - - - - - - - - - - - - - - - - - - - - - - - - - - E N D - - - - - - - - - - - - - - - - - - - - - - - - - - -
Presentation Transcript

  1. CISCO 200-120 exam in Just 24Hours!!

  2. QUESTION1: Which layer in the OSI reference model is responsible for determining the availability of the receiving program and checking to see if enough resources exist for thatcommunication? transport network presentation session application Answer:E QUESTION2: A network interface port has collision detection and carrier sensing enabled on a shared twisted pair network. From this statement, what is known about the network interfaceport? This is a 10 Mb/s switchport. This is a 100 Mb/s switchport. This is an Ethernet port operating at halfduplex. This is an Ethernet port operating at fullduplex. This is a port on a network interface card in aPC. Answer:C QUESTION3: A receiving host computes the checksum on a frame and determines that the frame is damaged. The frame is then discarded. At which OSI layer did this happen? physical session datalink

  3. transport network Answer:C QUESTION4: Which of the following correctly describe steps in the OSI data encapsulation process? (Choosetwo) The transport layer divides a data stream into segments and may add reliability and flow controlinformation. The data link layer adds physical source and destination addresses and an FCS to thesegment. Packetsarecreatedwhenthenetworklayerencapsulatesaframewithsource and destination host addresses and protocol-related controlinformation. Packets are created when the network layer adds Layer 3 addresses and control information to asegment. The presentation layer translates bits into voltages for transmission across the physicallink. Answer: A,D QUESTION5: For what two purposes does the Ethernet protocol use physical addresses? (Choosetwo.) to uniquely identify devices at Layer2 to allow communication with devices on a differentnetwork to differentiate a Layer 2 frame from a Layer 3packet to establish a priority system to determine which device gets to transmitfirst to allow communication between different devices on the samenetwork to allow detection of a remote device when its physical address isunknown Answer:A,E

  4. QUESTION6: In an Ethernet network, under what two scenarios can devices transmit? (Choose two.) when they receive a specialtoken when there is acarrier when they detect no other devices aresending when the medium isidle when the server grantsaccess Answer: C,D QUESTION7: What value is primarily used to determine which port becomes the root port on each nonroot switch in a spanning-treetopology? port priority number and MACaddress lowest port MACaddress pathcost VTP revisionnumber highest port prioritynumber Answer:C QUESTION8: Which of the following describes the roles of devices in a WAN? (Choosethree.) A CSU/DSU terminates a digital localloop. A modem terminates a digital localloop. A CSU/DSU terminates an analog localloop. A modem terminates an analog localloop. A router is commonly considered a DTEdevice. A router is commonly considered a DCEdevice.

  5. Answer: A, D,E QUESTION9: A network administrator is verifying the configuration of a newly installed host by establishing an FTP connection to a remoteserver. What is the highest layer of the protocol stack that the network administrator is using for thisoperation? application presentation session transport internet datalink Answer:A QUESTION10: Where does routing occur within the DoD TCP/IP referencemodel? application internet network transport Answer:B

  6. 100% passing Assurance Full Course Coverage Answers Verified by Experts Money Back Assurance Real & Accurate exam Questions

  7. You Can get complete file fromhere: 120.html