1 / 66

SEAMANSHIP CH. 4 MARLINSPIKE SEAMANSHIP

SEAMANSHIP CH. 4 MARLINSPIKE SEAMANSHIP. MARLINSPIKE. Again, the reference text for this chapter is CHAPMAN , PILOTING AND SEAMANSHIP, Marlinspike AUXSEA STUDENT STUDY GUIDE. 3 BASIC TYPES OF ROPE(LINE). Natural Synthetic Wire. NATURAL ROPE(Line). MANILA and COTTON

greenwald
Download Presentation

SEAMANSHIP CH. 4 MARLINSPIKE SEAMANSHIP

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. SEAMANSHIP CH. 4MARLINSPIKE SEAMANSHIP

  2. MARLINSPIKE • Again, the reference text for this chapter is CHAPMAN, PILOTING AND SEAMANSHIP, Marlinspike • AUXSEA STUDENT STUDY GUIDE

  3. 3 BASIC TYPES OF ROPE(LINE) • Natural • Synthetic • Wire

  4. NATURAL ROPE(Line) • MANILA and COTTON • About the only two kinds of natural rope(line) left. • LINE: Name given to all ropes when put to use aboard a vessel. • Two or three strands TWISTED clockwise to form one single strand.

  5. NATURAL ROPE(LINE)MANILA • Made from plant fibers. • Most popular • ADVANTAGES • Readily available • Inexpensive • Very durable

  6. MANILA • DISADVANTAGES • Manila deteriorates if stowed wet, damp or left in the bright sunlight. • NOTE • Manila has been virtually replaced by synthetic lines especially for running rigging

  7. COTTON LINE • ADVANTAGES • Pliable • Runs smoothly in blocks • DISADVANTAGES • ½ Strength of Manila • Susceptible to rot • Stretches, especially when wet

  8. WORKING TOOL(S)FID and MARLINSPIKE • A FID is the instrument or tool used to work on natural and synthetic lines and is usually made of WOOD,PLASTIC or ALUMINUM, SO AS NOT TO DAMAGE THE LINE while working it. • MARLINSPIKE: In appearance, it may look almost like a FID but is made of STEEL for endurance.

  9. MARLINSPIKE (FID)

  10. SYNTHETIC ROPEADVANTAGES • Almost impervious to salt, air, water and anything else that could destroy natural line • Tougher and stronger for their size than almost any other line material • Last a long time • Do a better job than any other kind of line

  11. SYNTHETIC ROPEDISADVANTAGES • It tends to “UNLAY” when cut. • Must be whipped or “stopped” immediately. • Open flame or Heating iron good for this.

  12. 4 TYPES OF SYNTHETIC ROPES • NYLON • DACRON • POLYPROPYLENE • POLYETHYLENE

  13. ADVANTAGES OF NYLON • HIGHEST ELASTICITY • CAN ABSORB 7 TIMES SHOCK LOAD OF MANILA • USED EXTENSIVELY FOR TOWING AND MOORING • HIGH RESISTANCE TO ROT • HIGH ABRASIVE RESISTANCE

  14. NYLONADVANTAGES Cont’d • Twice as strong as manila • Can use nylon of smaller diameter in replacing manila lines • Cheaper in the long run • Extremely flexible • No breaking in period

  15. NYLON Disadvantage NOTE MAIN DISADVANTAGE When it reaches the end of it’s elongation, it will SNAP, like a rubber band, becoming extremely dangerous to anybody or thing in it’s path.

  16. DACRON • Has all the properties of Nylon BUT; is NOT as Elastic • Fairly light in weight • Mostly has replaced cotton lines on most vessels

  17. POLYETHYLENE • ADVANTAGES • It floats. • DISADVANTAGES • Low abrasion resistance • Not nearly as supple as other synthetics • Knots need to be secured

  18. POLYPROPYLENE • Low abrasion resistance • Again not very supple • It FLOATS • **Stronger when it is wet**

  19. WIRE ROPE • Generally confined to use on sailing vessels and larger boats. • Many strands of wire are wound over an inner core of either wire or fabric such as cotton or a synthetic fabric. • The core provides a source of lubrication(when oiled)(or graphite) to ease the friction of the wires and also provides some elasticity or give.

  20. WIRE ROPE • 5 GRADES RELATIVE TO STRENGTH • IMPROVED PLOW STEEL • PLOW STEEL • MILD PLOW STEEL • TRACTION STEEL • IRON

  21. WIRE ROPE • Used where GREAT STRENGTH or HEAVYLOADING is needed, such as STANDING RIGGING and CABLE TOWING • Extremely stiff • Must use a MARLINSPIKE to work with it • Difficult to work with

  22. CARING FOR YOUR LINES • Neglect can be very expensive. TAKE CARE OF YOUR LINES. • DO NOT OVERLOAD: Generally, safe working strength is 1/5 the BREAKING strength. • PROTECT AGAINST ABRASION: Always use chaffing gear. • AVOID SUDDEN STRAINS ON THE LINE: • KEEP YOUR LINES CLEAN: Sand, dirt and grit will grind away the material in a line. Wash them as needed.

  23. LINE CARE (Cont’d) 6. STORE YOUR LINES PROPERLY: a. FAKING: YES. When appropriate b. COILING: YES. When appropriate c. FLEMISHING: YES. When appropriate d. CHORDING:NO. Bunched up and thrown into a rope locker! Even when you do it wrong, there is a proper name for it! DO NOT CHORD your lines! .

  24. COILED-FLEMISHED-FAKED

  25. LINE CARE Cont’d 7. Match your line to the use 8. Keep all chemicals away 9. Avoid excess wear 10. Avoid kinks 11. Don’t run lines over sharp edges

  26. PARTS OF A LINE Overhand Loop Working End Underhand Loop Standing Part Bitter End

  27. DIPPING THE EYE • Used where more than one vessel’s mooring line is used on the same pile. • DOCKING: Your EYE SPLICE up through the other eye splices – over the top and let settle around the piling. • UNDOCKING: lift your eye splice up over the piling then pull through other eye splices from the bottom. • YOU’RE ON YOUR WAY.

  28. DIPPING THE EYE

  29. SQUARE (REEF) KNOT • Most common way to join two lines of EQUAL DIAMETER together, where no great load is anticipated. • The square knot will JAM if heavily loaded, making it almost impossible to break it down without cutting it out. • It may also be forced into two half hitches, under great strain.

  30. SQUARE KNOT animation

  31. BOWLINE • Used to form a TEMPORARY LOOP in the end of a line. • Won’t slip under a load • Easy to tie and untie • One of the MOST USEFUL knots we have today.

  32. BOWLINE animation

  33. HALF HITCH • Used in conjunction with other knots. • Round turn with two half hitches commonly used as a long term fastening to secure a line to a piling.

  34. Round Turn

  35. Round Turn animation

  36. HALF HITCH animation

  37. TWO HALF HITCHES USED TO TIE A LINE TO A RING, PILE, POST OR GROMMET EASY TO UNTIE UNDER TENSION MORE PERMANENT THAN A CLOVE HITCH

  38. CLOVE HITCH • Used to TEMPORARILY fasten a line to a piling or other attachment. • MUST WATCH IT(so that it does not undo). • When under a strain, it will not slip. • When under a hard strain, it will set up tight and may be difficult to break down. • On the other hand, if left slack, it may work itself loose.

  39. CLOVE HITCH animation

  40. TIMBER HITCH • Very useful in towing logs or other similar objects. • Fast and easy knot to tie and break down. • If you use half hitches with this knot, tie them FIRST , then proceed with the timber hitch.

  41. TIMBER HITCH animation

  42. ROLLING HITCH • A utility knot which can be tied around another line already under strain to maintain the strain. • Can be be bent to a spar or other similar object. • Used to form a bridle for towing.

  43. ROLLING HITCH (UTILITY)

  44. SHEET OR BECKET BEND • Used to tie two lines of UNEQUAL DIAMETER together. • Easy to break down after a heavy strain. • DOUBLE BECKET: Simply an extra turn back under and through.

  45. SHEET OR BECKET BEND animation

  46. DOUBLE BECKET/SHEET BEND

  47. SPLICING • Preferred method of joining two lines together • EYE SPLICE:To make a PERMANENT EYE at the end. • LONG SPLICE: Does NOT increase diameter of the line. Good for use with blocks, sheeves. • SHORT SPLICE: May increase lin Preferred method of joining two lines together e diameter and is not used to run through a block, etc.

  48. MOORING DEVICES • BITTS • BOLLARDS • CLEATS • SAMPSON POSTS

  49. BITTS • Used to moor large vessels. • Normally found on commercial piers.

More Related