1 / 15

ES 202 Fluid and Thermal Systems Lecture 7: Mechanical Energy Balance (12/16/2002)

ES 202 Fluid and Thermal Systems Lecture 7: Mechanical Energy Balance (12/16/2002). Assignments. Reading: Cengel & Turner Section 11-4 ES 201 notes Homework: 11-5, 11-6 in Cengel & Turner notion of combined efficiency. Road Map of Lecture 7. Final attempt on curved surfaces

garran
Download Presentation

ES 202 Fluid and Thermal Systems Lecture 7: Mechanical Energy Balance (12/16/2002)

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. ES 202Fluid and Thermal SystemsLecture 7:Mechanical Energy Balance (12/16/2002)

  2. Assignments • Reading: • Cengel & Turner Section 11-4 • ES 201 notes • Homework: • 11-5, 11-6 in Cengel & Turner • notion of combined efficiency

  3. Road Map of Lecture 7 • Final attempt on curved surfaces • Steady state devices • revisit energy and entropy equation • nozzle, diffuser, turbine,compressor, heatexchanger • function • design assumption • modeling assumption • Close examination of energy equation • means of transport • zero production • mechanical energy vs thermal energy • flow work, kinetic energy, potential energy • Bernoulli’s equation

  4. Compare the hydrostatic forces acted on Surface AB (not thebottom of the tank) in the following configurations: A A A B B B Final Attempt on Curved Surfaces

  5. Major Conclusions • For inclined submerged surfaces (plane or curved) with same end points: • total horizontal force is the same • total vertical force differs (depending on the weight of fluid above/below the surface)

  6. End of Hydrostatics

  7. Revisit Energy Equation • Mean of transport: • heat transport • work transport • mass transport • Enthalpy: h = u + p / r consists of internalenergy and flow work (Do not double count flow work in Wout!) • Internal energy is a measure of molecular activities at the microscopic level (strongly dependent on temperature) while kinetic and potential energies are measures of bulk fluid motion

  8. Revisit Entropy Equation • Mean of transport: • heat transport • mass transport • There is no entropy transport associated with work, i.e. work transport of energy is entropy-free. This is the major difference between the two energy transfer modes: work and heat. Work is better! • Entropy production is always non-negative!

  9. Steady-State Devices • List the purpose (function) for the following devices: • nozzle • diffuser • turbine • pump, compressor, blower, fan • heat exchanger

  10. Turbine • Steam turbine • Water turbine (hydro-electricity) • Wind turbine (hill slopes) • Gas turbine engine • compressor • combustor • turbine • good power to weight ratio (multiple rotor-stator stage)

  11. Steady-State Devices (cont’d) • What does the energy equation reduce to for the following devices: • nozzle • diffuser • turbine • compressor, fan, blower, pump • heat exchanger

  12. Close Examination of Energy Equation • Energy equation again • Components of mechanical energy • flow work (pressure energy in C & T) • kinetic energy • potential energy • Thermal energy • thermodynamic property u • Energy components

  13. Mechanical Energy Vs Thermal Energy • Mechanical energy vs thermal energy • mechanical energy can freely change its form among various components • mechanical energy can be converted to workcompletely (without loss) if the system is reversible • example: spring-mass system in simple harmonic motion • thermal energy cannot be converted to work completely (the second law of thermodynamics imposed limitation to the conversion) • example: spring-mass system under influence of friction • the first law of thermodynamics (conservation of energy) does not differentiate the different forms of energy but the second law does • mechanical energy is a “higher quality” form of energy

  14. Energy Equation in Steady State • Assumptions • steady • adiabatic • no shaft work or friction • small changes in thermal energy relative to mechanical energy (good for low speed flows) • Conservation of mechanical energy • Interpretation: interchange of mechanical energy among its various forms

  15. Bernoulli’s Equation • Traditional derivation is based on momentum equation • Warning: Its simplicity may often lead to incorrect application • Remember the assumptions (limitations) • steady • no shaft work or friction • small change in thermal energy • constant density • along flow direction • Examples: application to nozzle and diffuser

More Related