1 / 47

Physics I

Physics I. Direct Current Electricity DC. Assignment. P&P22:1,3,10,13-16,32,62-64 P&P23:4,7,11,16,55,57-59,64-67 Circuit Practice: http://www.picra.net/csk/physics/CircuitProblems.html. 1. Current Electricity – charges in motion .

elwyn
Download Presentation

Physics I

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Physics I Direct Current Electricity DC

  2. Assignment • P&P22:1,3,10,13-16,32,62-64 • P&P23:4,7,11,16,55,57-59,64-67 • Circuit Practice: • http://www.picra.net/csk/physics/CircuitProblems.html

  3. 1. Current Electricity – charges in motion • A. Circuit – a continuous loop through which electricity can flow. It must contain • 1. Energy source – battery, generator • 2. Conductor – copper wire is common • 3. Load – device(s) that converts electrical energy to other useful forms of energy

  4. 1. Parallel Circuit - more than 1 path is provided for current to flow 2. Series Circuit - one path for current to flow B. Circuit Types

  5. Schematic Symbols

  6. Ohm’s Law R = V R, Resistance in Ohms, W I V, Voltage in volts, v I, current in amperes, a E = IR or V = IR E, voltage in volts, for the overall circuit V, potential drop across a section of a circuit

  7. 2. Cardinal rules for Resistors • A. Voltage or Electromotive Force (across battery) is equal in parallel • Vbattery = V1 = V2 = V3 = ... • B. Current is additive in parallel • Itotal = I1 + I2 + I3 + ... Kirchhoff’s 1st Law or Junction Rule - the total current entering a junction must be equal to the total current leaving the junction.

  8. C. Resistance in Parallel

  9. Equivalent Resistance

  10. Cardinal Rule for Req • This is the concept of equivalent resistance. The equivalent resistance of a circuit is the amount of resistance which a single resistor would need in order to equal the overall effect of the collection of resistors which are present in the circuit. For parallel circuits, the mathematical formula for computing the equivalent resistance (Req) is • 1 / Req = 1 / R1 + 1 / R2 + 1 / R3 + ...

  11. Series Circuit – only 1 path is provided for current

  12. Voltage is additive in series • Vbattery = V1 + V2 + V3 + ... Kirchoff’s 2nd Law or the Loop Rule: The algebraic sum of the potential differences that occur around a complete circuit is equal to zero. E - (V1 + V2 + V3 + …) = 0

  13. Current in series • Ibattery = I1 = I2 = I3 = ... Ibattery = I1 = I2 = I3 =  V / Req

  14. Which leads us to • Rt = R1 + R2 + R3 + ... •  since the current is the same

  15. Cardinal rules - Parallel • E = Vt = V1 = V2 = V3 = … • Voltages are equal in parallel • It = I1 + I2 + I3 + … • Current is additive in parallel • 1/Rt = 1/R1 + 1/R2 + 1/R3 • Or: Rt = 1 • 1/R1 + 1/R2 + 1/R3 • Or As more resistance is added, the resistance goes DOWN!!

  16. Cardinal Rules - Series • E = Vt = V1 + V2 + V3 • I t = I1 = I2 = I3 • Rt = R1 + R2 + R3

  17. Power, rate of doing work • P = IV P = I2 R • Energy, E = Power x time, j/s x s = joule • P, Power: watt = joule/sec • I, Current: ampere = coulomb/sec • V, Voltage: volt = joule/coulomb • R, Resistance: ohm • E, Energy: joule

  18. Sample Problem • 22/1 The current through a light bulb connected across the terminals of a 125 v outlet is 0.50 a. at what rate does the bulb convert electric energy to light? • P = IV • P = (0.50 a)(125 v) • P = 63 w

  19. Meters • Voltmeter – measure difference in potential between 2 points in a circuit • ALWAYS connected in parallel with the part of the circuit to be measured (acts as a load) http://www.facstaff.bucknell.edu/mastascu/elessonshtml/Measurements/MeasVolt.html

  20. Ammeter – measures current • ALWAYS placed in series in a circuit • Be sure current does not exceed range of meter (use rheostat or “tap” or set meter at highest range, if possible) The ammeter is placed in SERIES with one lead of a circuit. It must be placed around the correct way so the needle moves up-scale.  http://www.talkingelectronics.com/html/CctSymbolsE-Book-Web/CircuitSymbolsE-Book-Web.html

  21. Galvanometer • Used to measure weak electric currents only

  22. Rheostat - variable resistor • Controls amount of current flow • Controls voltage across a load • Protects expensive instruments

  23. Rules for Meter Usage • Handle gently • Connect voltmeter in parallel • Connect ammeter in series • Polarity labels tell how to connect meters • Red (+) and Black (-) • + should be wired directly or though other components to the + terminal of the voltage source

  24. Meter Rules Continued • When taking readings of unknown amounts, start at highest range or just tap • Know meter scales BEFORE closing a circuit so accurate readings can be taken quickly • Using tapping rule when first closing a circuit so accurate readings can be taken quickly

  25. Meter rules, cont. • Have circuit approved before closing the circuit • Report trouble immediately • AC & DC meters are NOT interchangeable (unless so designed) • Avoid overheating • Joule’s Law Q = I2 RT / J • Q aI2

  26. Problem Applications

  27. 15. continued

  28. On the prior slide, simplification shown in the diagrams gives way to what is needed to be done mathematically using the Cardinal Rules: Series: V is +, I is =, R is + Parallel: V is =, I is +, R is 1/R +

  29. More practice at… • http://www.picra.net/csk/physics/CircuitProblems.html

  30. Nature of the Material R = rL/A r is resistivity of a conductor in Wcm L is length of conductor, cm A is cross sectional area of conductor, cm2 Wheatstone Bridge Other methods of determining resistance

  31. Problem sample • What is the resistance of Copper wire 20. m long, 0.81 mm diameter at 20.0oC? (Resistivity, rCu at 20.0oC = 1.72x10-6Wcm) • R = r L = 1.72x10-6Wcm) (2000cm) • A p(8.1x10-2cm)2 • 4 • R =

  32. A Wheatstone bridge is a measuring instrument invented by Samuel Hunter Christie in 1833 and improved and popularized by Sir Charles Wheatstone in 1843. It is used to measure an unknown electrical resistance by balancing two legs of a bridge circuit, one leg of which includes the unknown component. Its operation is similar to the originalpotentiometer except that in potentiometer circuits the meter used is a sensitive galvanometer. Wheatstone's bridge circuit diagram. In the circuit at right, Rx is the unknown resistance to be measured; R1, R2 and R3 are resistors of known resistance and the resistance of R2 is adjustable. If the ratio of the two resistances in the known leg (R2 / R1) is equal to the ratio of the two in the unknown leg (Rx / R3), then the voltage between the two midpoints will be zero and no current will flow between the midpoints. R2 is varied until this condition is reached. The current direction indicates if R2 is too high or too low. Detecting zero current can be done to extremely high accuracy (see Galvanometer). Therefore, if R1, R2 and R3 are known to high precision, then Rx can be measured to high precision. Very small changes in Rx disrupt the balance and are readily detected. If the bridge is balanced, which means that the current through the galvanometer Rg is equal to zero, the equivalent resistance of the circuit between the source voltage terminals is: R1 + R2 in parallel with R3 + Rx http://en.wikipedia.org/wiki/Wheatstone_bridge

  33. members.shaw.ca/roma/res_cap.html

  34. Sources • http://www.glenbrook.k12.il.us/gbssci/phys/Class/circuits/u9l4a.html • http://www.ieee.org/portal/cms_docs_iportals/iportals/education/preuniversity/tispt/pdf/lessons/serpar.pdf

More Related